Replacing a brake light bulb takes 5 to 15 minutes and costs $5 to $25 per bulb, depending on your vehicle and bulb type
A burned-out brake light is a safety issue and a traffic violation in every state. The process itself is straightforward: access the light housing from inside your trunk or under the hood, remove the old bulb, and install a new one. Most vehicles let you do this without tools, though some require removing a single screw or clip. The hardest part is usually figuring out which bulb you need and whether your car's design requires you to remove the entire housing or just twist out the socket.
This guide walks you through the steps, shows you where to find the bulb type your vehicle needs, and explains what to do if the light still doesn't work after you've replaced the bulb.
Key Takeaways
- Brake light bulbs are accessed from inside your trunk on most sedans and SUVs, or from under the hood on some trucks and older vehicles.
- Your vehicle's manual or a parts store can tell you the exact bulb type and socket style your car uses.
- Most bulbs twist out of their socket counterclockwise; some slide straight out or require removing a housing panel first.
- If the new bulb doesn't light, the problem is usually a blown fuse, a corroded socket, or a wiring issue — not the bulb itself.
Locate the brake light housing on your vehicle
On sedans, coupes, and most SUVs, the brake light housings are accessed from inside the trunk. Open your trunk, look at the inner wall where the light is, and you'll see either a plastic panel you can peel back or a housing that protrudes inward. On pickup trucks, the lights are often accessed from under the hood or from the side of the bed. On some older vehicles, you may need to remove the entire taillight assembly from outside, which requires removing bolts or clips visible from the rear bumper.
If you're unsure which end of the vehicle has the brake light you need to replace, sit in the driver's seat, press the brake pedal, and have someone stand behind the car to tell you which light is out. Brake lights are always at the rear of the vehicle, positioned at the top corners of the trunk lid or tailgate.
Find the correct bulb type for your vehicle
Brake light bulbs come in different sizes and socket types. The most common are 1157 (dual-filament, used for brake and running lights combined), 1156 (single-filament, brake only), and 7440 (wedge-style, common in newer vehicles). Your vehicle's owner's manual lists the exact bulb type in the maintenance or specifications section. If you don't have the manual, take a photo of your current bulb or the housing and show it to a parts store employee — they can match it in seconds.
You can also look up your vehicle's year, make, and model on an online parts retailer or your manufacturer's website. Write down the bulb type before you go to the store or order online. Bulbs typically cost $5 to $15 each, though some specialty or LED bulbs run higher.
Remove the old bulb from its socket
Once you've located the housing, look for how the bulb is held in place. Most bulbs sit in a socket that twists counterclockwise — push gently on the bulb and turn it left until it releases. Some bulbs slide straight out without twisting. A few vehicles require you to remove a plastic panel or unscrew a single bolt to access the socket, but this is less common.
If the bulb is stuck or the socket is corroded, spray a small amount of electrical contact cleaner or penetrating oil around the base and wait a minute before trying again. Don't force it — forcing can crack the socket or break the bulb inside the housing. If it still won't budge, stop and take the vehicle to a shop rather than risk damaging the housing.
Install the new bulb and test it
Insert the new bulb into the socket, making sure the pins or tabs align with the slots in the socket. Push gently and turn clockwise until you feel resistance — don't overtighten. For wedge-style bulbs, straightforward push straight in until it seats. The bulb should be snug but not forced.
Close the trunk or hood, sit in the driver's seat, and press the brake pedal while looking in a mirror or having someone stand behind the car to confirm the light is on. If it lights up, you're done. If it doesn't, move to the troubleshooting section below.
What to do if the new bulb doesn't light
A new bulb that doesn't work usually means the problem isn't the bulb itself. The most common causes are a blown fuse, a corroded socket, or a wiring issue. Start by checking the fuse. Your vehicle's fuse box is typically under the hood or inside the cabin near the steering column. The owner's manual shows which fuse controls the brake lights. Pull that fuse out — if the wire inside is broken or blackened, replace it with a fuse of the same amperage (usually 10 or 15 amps). Fuses cost less than $1.
If the fuse is intact, the socket itself may be corroded. Remove the bulb again and spray electrical contact cleaner into the socket, working the spray nozzle around the inside. Let it dry for a minute, reinsert the bulb, and test again. If the light still doesn't work after these steps, the wiring or the brake light switch may be faulty — this requires a shop visit or a mechanic's diagnosis.
When to take your vehicle to a shop
Take your car to a shop if the new bulb doesn't light after you've checked the fuse and cleaned the socket, if you can't access the housing without removing body panels, or if the socket itself is cracked or damaged. A shop can diagnose wiring problems, test the brake light switch, and replace corroded sockets. This typically costs $50 to $150 in labor, depending on the vehicle and the underlying issue.
Don't ignore a burned-out brake light. It's a safety hazard — other drivers can't see you braking — and it's a traffic violation that can result in a ticket. Most states allow officers to stop you for a broken brake light, and fines range from $20 to $100 depending on the state.
Frequently Asked Questions
Can I replace a brake light bulb without removing the entire taillight housing?
On most vehicles, yes. You access the bulb from inside the trunk or under the hood and twist or slide it out of its socket without removing the outer housing. Some older vehicles or certain truck models require removing bolts or clips from outside to access the bulb, but this is less common on modern cars.
What's the difference between a 1157 and a 1156 bulb?
A 1157 bulb has two filaments — one for the running light and one for the brake light. A 1156 has one filament for brake only. Using the wrong type won't damage anything, but the light may not function correctly. Your manual or a parts store can confirm which your vehicle needs.
Why does my brake light keep burning out?
Frequent burnouts usually mean the socket is corroded, the wiring is loose, or there's an electrical fault causing excess voltage. Clean the socket with electrical contact cleaner first. If bulbs continue to burn out within weeks, have a mechanic check the wiring and charging system.
Is it safe to drive with a brake light out?
No. A burned-out brake light is a safety risk and a traffic violation. Other drivers won't see you braking, increasing the risk of a rear-end collision. Replace it before driving, or have it replaced at a shop if you can't do it yourself.
Do I need to buy a specific brand of brake light bulb?
No. Any bulb of the correct type (1157, 1156, 7440, etc.) will work. OEM (original equipment manufacturer) bulbs are often more expensive than aftermarket equivalents but perform the same function. LED bulbs are brighter and last longer but cost more upfront.