What resetting your check engine light means and when you can do it
Resetting your check engine light — also called the malfunction indicator lamp or MIL — means clearing the diagnostic trouble code that triggered it. The light comes on when your vehicle's onboard diagnostic system detects a problem with the engine, emissions system, or transmission. You can reset it yourself using an OBD-II scanner, or a mechanic can reset it during a repair visit. However, resetting the light does not fix the underlying problem — it only turns off the warning. If the issue remains unfixed, the light will come back on.
Some states require you to pass an emissions inspection before you can register your vehicle, and a check engine light will cause you to fail that test. This is why many people want to reset the light. But you should understand what the light is telling you before you clear it, because driving with an unrepaired emissions problem can damage your engine and fail you at inspection again.
Key Takeaways
- A check engine light indicates a specific problem stored in your vehicle's computer, which you can read using an OBD-II scanner before deciding whether to reset it.
- You can reset the light yourself with a scanner, but the underlying problem will remain and the light will return unless you repair it.
- Many states will not pass your vehicle for emissions inspection with a check engine light on, even if the problem is minor.
- A mechanic can read the code, repair the issue, and reset the light as part of the service, which is often the most reliable approach.
- Resetting the light without fixing the problem may cause your vehicle to fail inspection again or damage your engine over time.
How to read the code before you reset
Before you reset the light, you need to know what problem triggered it. Your vehicle stores a diagnostic trouble code in its computer that describes the issue. You can read this code using an OBD-II scanner, a handheld device that plugs into the diagnostic port under your dashboard (usually on the left side, below the steering wheel). The port is a 16-pin connector that looks like a rectangular slot.
You can buy a basic OBD-II scanner for $25 to $100, or you can borrow one from a friend, rent one from an auto parts store, or visit a mechanic who will read the code for free or for a small fee. Once you plug in the scanner and turn on the ignition (without starting the engine), it will display the trouble code — a letter followed by four numbers, like P0420 or P0171. Write down the exact code.
Look up the code online or in your vehicle's service manual to understand what it means. Some codes point to straightforward fixes like a loose gas cap, while others indicate serious emissions system problems. Knowing what the code means helps you decide whether to reset the light yourself, take the vehicle to a mechanic, or investigate further.
Resetting the light yourself with a scanner
If you own an OBD-II scanner, you can reset the check engine light yourself. Plug the scanner into the diagnostic port, turn on the ignition, and navigate the scanner's menu to the "Clear Codes" or "Erase Codes" option. The exact steps vary by scanner model, so check the instructions that came with yours. Once you select clear, the scanner will erase the trouble code and turn off the light.
The light will stay off as long as the problem that triggered it does not happen again. If the underlying issue remains — for example, a faulty oxygen sensor or a leak in the emissions system — your vehicle's computer will detect it again within a few days or weeks, and the light will come back on. You will then need to address the actual problem or reset it again.
Resetting the light yourself is free if you own a scanner, but it does not solve the mechanical problem. Use this approach only if you have already identified and fixed the issue, or if you want to see whether the problem recurs on its own.
Having a mechanic reset the light after repair
The most reliable way to reset your check engine light is to have a mechanic diagnose the problem, repair it, and then reset the light as part of the service. A mechanic will read the trouble code, inspect the relevant system, perform the necessary repair, and then clear the code using their diagnostic equipment. Once the repair is complete, the light should not return.
The cost of this approach depends on what the problem is. A loose gas cap or a faulty sensor might cost $50 to $300 to fix, while a catalytic converter or transmission issue could cost much more. However, you are paying to actually solve the problem rather than just turning off the warning light. This is the approach you need if you want to pass an emissions inspection or if you want to avoid damaging your engine.
If you are unsure whether to repair the issue or reset the light yourself, ask a mechanic to read the code and give you an estimate. That way you can make an informed decision about whether the repair is worth the cost.
Check engine light and emissions inspection
Most states that require emissions testing will not pass your vehicle if the check engine light is on, regardless of what the underlying problem is. Some states also check whether your vehicle's diagnostic system is ready to test — a vehicle that has just had its codes cleared may show as "not ready" and fail for that reason alone.
If you reset the light just before an inspection, the vehicle may fail because the diagnostic system has not completed its self-test cycle yet. Your vehicle's computer runs continuous tests on the emissions system while you drive, and it can take 50 to 100 miles of normal driving for the system to report as "ready." If you reset the light and when ready go to inspection, you may fail because the system is not ready, even if there is no actual problem.
The safest approach is to have the underlying problem repaired by a mechanic before inspection. If you reset the light yourself, drive the vehicle normally for at least 50 miles before scheduling your inspection, so the diagnostic system has time to complete its tests and report as ready.
When you should not reset the check engine light
Do not reset the check engine light if you have not identified the problem it is warning you about. Clearing the code without fixing the issue is like turning off a smoke alarm without putting out the fire — the problem continues to exist and may get worse. Driving with an unrepaired emissions system problem can damage your catalytic converter, reduce fuel economy, and cause your engine to run poorly.
Do not reset the light if you are trying to hide a problem from a buyer or inspector. Resetting the light is legal, but selling a vehicle while concealing a known mechanical problem may violate your state's lemon law or consumer protection laws. If you are selling the vehicle, disclose the problem and let the buyer decide whether to purchase it as-is or ask you to repair it.
Do not reset the light repeatedly without addressing the underlying cause. If the light comes back on within a few days, the problem has not been fixed. Continuing to reset it will not solve the issue and may cause additional damage to your vehicle.
Tools and costs for resetting the light
An OBD-II scanner is the main tool you need to reset the check engine light yourself. Basic scanners that read and clear codes cost $25 to $100 and are available at auto parts stores, online retailers, and big-box stores. More advanced scanners with additional features cost $150 to $500 or more, but for reading and clearing a single code, a basic model is sufficient.
If you do not want to buy a scanner, you have other options. Many auto parts stores (such as AutoZone, O'Reilly, and Advance Auto Parts) will read your diagnostic code for free, though they may not clear it without a purchase. Some mechanic shops will read the code for free as well. If you decide to have the problem repaired, the mechanic's diagnostic fee (usually $50 to $150) is often waived if you proceed with the repair at their shop.
Resetting the light yourself costs nothing if you already own a scanner or can borrow one. Having a mechanic reset it after repair costs whatever the repair itself costs, which varies widely depending on the problem.
Frequently Asked Questions
Will resetting the check engine light fix my car?
No. Resetting the light only clears the warning from your dashboard. The mechanical problem that triggered the light remains unfixed. If the problem is still present, the light will come back on within days or weeks. You must repair the underlying issue to prevent the light from returning.
Can I reset the check engine light without a scanner?
You can disconnect your vehicle's battery for 15 minutes to clear the codes, but this is unreliable and may erase other important data from your vehicle's computer. Using an OBD-II scanner is faster and safer. Many auto parts stores will read your code for free, and a basic scanner costs $25 to $100.
How long does it take for the check engine light to come back on?
If the underlying problem still exists, the light typically returns within a few days to a few weeks, depending on how often the condition occurs. If the problem was temporary (like a loose gas cap), the light may not return. Drive normally for 50 to 100 miles after resetting to let your vehicle's diagnostic system complete its tests.
Will I fail emissions inspection if I reset the check engine light?
You may fail if the light comes back on before inspection, or if your vehicle's diagnostic system is not ready (which can happen when ready after resetting). Even if the light is off, if the underlying problem still exists, you will fail inspection. Have the problem repaired before inspection to may support you pass.
Is it illegal to reset the check engine light?
Resetting the light itself is legal. However, selling a vehicle with a known problem while concealing the check engine light may violate consumer protection laws in your state. Always disclose known mechanical problems to buyers or inspectors.