Both lights mean your Toyota has detected a problem with traction control and engine performance
When your Toyota displays both the Trac Off warning light and the Check Engine light at the same time, it signals that your vehicle's onboard diagnostic system has found faults in two related systems. The Trac Off light indicates that your traction control system has been disabled — either automatically by the car or manually by you. The Check Engine light means the engine control module has stored one or more diagnostic trouble codes related to engine, emissions, or transmission function. These two lights together often point to a single underlying problem rather than two separate issues.
The most common cause is a faulty oxygen sensor, mass airflow sensor, or throttle position sensor. When any of these sensors malfunction, the engine control module disables traction control as a safety measure because it cannot accurately monitor wheel slip and engine performance. Other frequent causes include a loose or damaged gas cap, a catalytic converter problem, or an issue with the vehicle's electrical system. The key point: you should not ignore this combination. While you may be able to drive short distances, the underlying fault needs diagnosis before it causes more expensive damage.
Key Takeaways
- Both lights appearing together usually means one problem affecting multiple systems, not two separate failures.
- Oxygen sensors, mass airflow sensors, and throttle position sensors are the most common culprits behind this combination.
- You need to read the diagnostic trouble codes using a scanner to know what actually failed — guessing at repairs wastes money.
- Traction control being off reduces your grip in slippery conditions, so avoid hard acceleration or cornering until the issue is fixed.
Why traction control shuts off when the engine has a fault
Your Toyota's traction control system relies on real-time data from multiple engine sensors to work properly. When the engine control module detects a sensor failure or engine misfire, it cannot trust the information it is receiving about engine load, fuel mixture, or wheel speed. Rather than risk giving you false traction control intervention — which could make you lose control — the system disables itself and lights the Trac Off warning.
This is a safety design, not a failure of the traction control system itself. The traction control hardware is usually fine. The problem is upstream: the engine is not running correctly, so the computer shuts down traction control until the engine issue is resolved. This is why fixing the Check Engine fault almost always makes the Trac Off light disappear on its own.
How to read your diagnostic trouble codes
The Check Engine light tells you a code has been stored, but it does not tell you what the code is. You need a diagnostic scanner to read it. You have three options: visit a Toyota dealership, take the car to an independent mechanic, or use a handheld OBD-II scanner you can buy or borrow.
A dealership scan typically costs $100 to $150 and gives you a detailed report tied to your vehicle's specific model year and systems. An independent shop usually charges $50 to $100 for the same scan. If you own a handheld OBD-II scanner (available for $25 to $100), you can read the code yourself by plugging it into the diagnostic port under the steering column. Many auto parts stores also offer free code reading if you ask — call ahead to confirm. Write down the exact code number (it will look like P0171 or P0420) because the same code means the same thing across all Toyota models.
Common diagnostic trouble codes that trigger both lights
Several codes appear frequently when both lights are on. P0171 and P0174 mean the engine is running too lean (not enough fuel), often caused by a vacuum leak, faulty oxygen sensor, or mass airflow sensor. P0300 indicates random misfires across multiple cylinders, usually from a bad spark plug, ignition coil, or fuel injector. P0420 signals a catalytic converter efficiency problem, which can stem from engine misfires sending unburned fuel into the converter.
P0101 points to a mass airflow sensor fault, and P0135 or P0155 indicate oxygen sensor circuit problems. P0440 and related codes flag issues with the evaporative emissions system, sometimes as straightforward as a loose gas cap. Once you have the code, you can research the specific cause and repair cost before you commit to a shop. The code narrows the problem from "something is wrong" to "this specific sensor or system is failing."
When you can drive with both lights on and when you cannot
A single Check Engine light with no other symptoms does not always mean you must stop driving when ready. Many faults — like a loose gas cap or a minor oxygen sensor drift — allow the car to run and drive normally. However, if you notice rough idling, hesitation during acceleration, loss of power, or unusual noise from the engine, stop driving and have the car towed or driven directly to a shop. These symptoms indicate a more serious fault that could damage the engine or catalytic converter.
With the Trac Off light on, your vehicle loses electronic stability control and traction control. This means your wheels can spin more easily on wet or slippery surfaces, and the car will not automatically correct oversteer or understeer. Avoid driving in rain, snow, or on wet roads until the fault is fixed. Do not accelerate hard or take sharp corners at speed. If you must drive, keep speeds low and stay on dry pavement. The longer you drive with a Check Engine fault, the higher the risk of damaging the catalytic converter, which is an expensive repair.
What repairs typically cost
Repair costs vary widely depending on which component has failed. An oxygen sensor replacement runs $150 to $400 including labor at most shops. A mass airflow sensor is $200 to $500. A throttle position sensor is $150 to $350. A catalytic converter — the most expensive common culprit — ranges from $400 to $1,200 or more depending on your Toyota model. A loose gas cap costs nothing to fix; you just tighten it and clear the code.
Before authorizing any repair, ask the shop to show you the diagnostic code and explain why that code points to the part they want to replace. Reputable shops will do this without hesitation. If a shop wants to replace expensive parts without showing you the code or explaining the diagnosis, get a second opinion. Many Check Engine faults can be diagnosed accurately with the code alone, so you should never pay for guesswork.
How to clear the lights after repair
Once the underlying fault is fixed, the Check Engine light should turn off on its own after a few drive cycles (typically 10 to 20 miles of normal driving). The Trac Off light will also disappear. You do not need to clear the code manually unless the light remains on after the repair is complete and verified.
If you want to clear the code yourself, you can disconnect the negative battery terminal for 15 minutes, which will reset the engine control module. However, this also erases all stored codes, which means you lose the diagnostic information if the problem persists. It is better to let the shop verify the repair worked by confirming the code is gone using their scanner. If the lights come back on within a few days or weeks, the original repair did not solve the problem, and you should return to the shop under warranty.
Frequently Asked Questions
Can I drive my Toyota with both lights on?
Short distances on dry roads are usually safe if the engine runs smoothly and you do not notice hesitation or rough idling. However, you should not drive in rain or snow, and you should have the car scanned within a day or two. If the engine feels rough or sounds wrong, do not drive it — have it towed to a shop instead.
Will the Trac Off light go away on its own?
No. The Trac Off light will stay on until the underlying engine fault is fixed. Traction control itself is not broken; the engine problem is preventing it from working safely. Once you repair the engine issue, the light will turn off automatically.
What does a loose gas cap have to do with the Check Engine light?
A loose or missing gas cap allows fuel vapors to escape from the tank, which triggers the evaporative emissions system fault code. This is one of the easiest and cheapest faults to fix — just tighten or replace the cap. If that was the only problem, the light should clear within a few drive cycles.
Should I go to a Toyota dealership or an independent mechanic?
Both can diagnose and repair the problem. Dealerships charge more but have factory parts and detailed model-specific knowledge. Independent shops are usually cheaper and can often fix the same issues. Get a diagnostic scan and estimate from both before deciding. For common faults like oxygen sensors, an independent shop is usually the better value.
What if the Check Engine light comes back after I had it fixed?
Return to the shop that did the repair — most offer a warranty on parts and labor, typically 30 days or 1,000 miles. If the same code returns, the original diagnosis may have been incomplete, or a related component may have failed. Ask the shop to investigate further at no additional charge under warranty.