What a crankshaft sensor does and why it fails
A crankshaft position sensor (often called a crank sensor) tells your engine's computer where the crankshaft is at any given moment. The crankshaft is the shaft that converts the up-and-down motion of your pistons into the rotating motion that turns your wheels. The sensor reads a toothed ring on the crankshaft and sends that position data to the engine control unit dozens of times per second. Without accurate position information, your engine cannot time the spark plugs or fuel injectors correctly.
When a crank sensor fails, you will usually see a check engine light and experience one or more of these symptoms: the engine cranks but won't start, rough idle, stalling at stops, loss of power during acceleration, or the engine cutting out while you are driving. Some cars will not start at all with a failed sensor because the computer has no way to know when to fire the plugs.
Crank sensors fail because they live in a hot, vibrating environment near the engine. The sensor itself is a small coil of wire wrapped around a magnet, and that coil can crack or corrode over time. The connector can also corrode, or the wiring can break. Most crank sensors last between 80,000 and 150,000 miles, though some fail much earlier if the engine bay is exposed to water or salt.
Key Takeaways
- A crankshaft sensor tells your engine computer where the crankshaft is positioned so it can time the spark plugs and fuel injectors correctly.
- The sensor is usually located near the crankshaft pulley at the front or bottom of the engine, and you will need to remove the wheel well cover or lower the car to reach it.
- Replacement takes one to three hours depending on how accessible the sensor is on your specific car, and you will need a socket set, a new sensor, and often a jack and jack stands.
- The job requires disconnecting the sensor connector, unbolting the sensor, and installing a new one in the same position — no special tools or computer reprogramming needed.
- If you are not comfortable working under a running car or using a jack, a shop can do this job for $150 to $400 in labor plus the cost of the sensor itself.
Where the crankshaft sensor is located on your engine
The crank sensor location varies by make and model, but it is always mounted near the crankshaft itself so it can read the toothed ring. On most cars, it sits at the front of the engine near the crankshaft pulley (the large wheel that drives your serpentine belt), or at the bottom of the engine block near the oil pan. Some vehicles have two crank sensors — one near the front and one near the back — but most have just one.
To find yours, consult your owner's manual or a repair manual for your specific year, make, and model. The manual will show you exactly where it is and what it looks like. If you do not have the manual, you can search online for "[your year, make, model] crankshaft sensor location" and find diagrams or videos showing the exact spot. The sensor itself is usually a cylindrical piece about 2 to 3 inches long with a wire connector on one end and a bolt hole on the other.
On some cars — particularly front-wheel-drive vehicles — you may need to remove the right front wheel and wheel well cover to access the sensor. On others, you may need to lift the engine slightly or remove other components like the alternator or air intake. This is why knowing your specific car's layout before you start is crucial.
Tools and parts you will need
You will need a new crankshaft sensor for your exact year, make, and model. Do not guess at the part number — sensors are not universal, and installing the wrong one will not work. Order the part from a parts store or online retailer using your vehicle identification number (VIN), or ask a shop to confirm the part number before you buy it. The sensor itself usually costs between $40 and $150 depending on the brand and whether it is OEM (original equipment manufacturer) or aftermarket.
For tools, you will need a socket set with the correct size socket for the sensor bolt (usually 10mm, 13mm, or 15mm — check your manual), a ratchet, and possibly an extension bar if the sensor is in a tight spot. You will also need a jack and jack stands if the sensor is underneath the car, or a set of ramps if you prefer not to use a jack. A flashlight or headlamp is essential because the sensor is often in a dark spot. Have a clean rag or paper towels on hand in case there is oil or dirt around the sensor.
If you need to remove other parts to access the sensor — like the wheel well cover, air intake, or alternator — you may need additional sockets or a screwdriver. Again, your repair manual will tell you exactly what needs to come off.
Step-by-step replacement process
Step 1: Disconnect the battery. Locate the negative terminal on your battery (the black cable) and loosen the nut that holds it to the terminal post. Remove the cable and set it aside. This prevents any electrical shorts while you are working. Wait a few minutes for the electrical system to discharge.
Step 2: Locate and access the sensor. If the sensor is underneath the car, safely lift the vehicle using a jack and find it with jack stands under the frame. Never work under a car supported only by a jack. If you need to remove the wheel well cover or other components, do that now. Use your flashlight to locate the sensor and trace its wiring back to the connector.
Step 3: Disconnect the sensor connector. The connector is usually held in place by a small clip or latch. Gently squeeze or press the clip and pull the connector straight away from the sensor. Do not yank on the wires themselves — pull on the connector body. If the connector is stuck, wiggle it gently side to side while pulling.
Step 4: Remove the old sensor. Using your socket and ratchet, unbolt the sensor from its mounting location. There is usually one bolt, though some sensors have two. Keep the bolt in a safe place. Carefully pull the sensor straight out of its hole. You may need to wiggle it slightly if it is a tight fit. Inspect the hole for any dirt or debris and wipe it clean with a rag.
Step 5: Install the new sensor. Take the new sensor and insert it into the hole in the same position and orientation as the old one. The connector should point in the same direction the old one did. Hand-tighten the bolt first, then use your socket and ratchet to snug it down. Do not over-tighten — the bolt should be snug but not so tight that you risk stripping the threads. Most sensor bolts need only 15 to 25 foot-pounds of torque, which is hand-tight plus a quarter turn.
Step 6: Reconnect the sensor connector. Align the connector with the sensor and push it straight on until you hear or feel a click. The clip should snap into place. Tug gently on the connector to make sure it is fully seated.
Step 7: Reassemble and reconnect the battery. If you removed any covers or components, reinstall them now. Lower the car back to the ground if you lifted it. Reconnect the negative battery cable by sliding it back onto the terminal post and tightening the nut. Do not over-tighten — snug is enough.
Step 8: Clear the check engine light. Start the engine and let it run for a few minutes. The check engine light may stay on for a few driving cycles while the computer relearns the sensor signal. If the light does not go off after 50 to 100 miles of normal driving, you may have a wiring problem or the sensor may not be seated correctly. Some auto parts stores will read your check engine code for free and tell you what the problem is.
When to do this job yourself versus taking it to a shop
Replacing a crank sensor is a straightforward job if you have basic mechanical skills and the right tools. The actual replacement takes 30 minutes to an hour once you have the sensor exposed. However, the time it takes to access the sensor varies wildly depending on your car. On some vehicles, the sensor is right there in plain sight. On others, you may need to remove the wheel, the wheel well cover, the air intake, and possibly other components, which can add an hour or more to the job.
If you are comfortable using a jack and jack stands, have a socket set, and do not mind getting under the car, this is a reasonable DIY job. If you are not confident with those tools, or if your car requires removing many other parts to access the sensor, a shop can do it faster and you will not risk damaging other components. A typical shop will charge $150 to $400 in labor depending on how long it takes to access the sensor on your specific car, plus the cost of the sensor itself.
One more consideration: if you have never done this kind of work before, watch a video of someone replacing the sensor on your exact year, make, and model before you start. Seeing the actual location and the order of steps will save you time and frustration.
What happens if you ignore a failed crankshaft sensor
A failed crank sensor will eventually leave you stranded. In the early stages, you might just notice rough idle or a check engine light. But as the sensor deteriorates further, the engine will stall while you are driving, and you may not be able to restart it. If this happens on a highway or in traffic, it is a safety hazard.
Driving on a failing sensor can also damage other parts. If the computer cannot time the spark plugs correctly, the engine may run too lean or too rich, which can damage the catalytic converter or cause the engine to overheat. The longer you wait, the more expensive the repair becomes. A crank sensor replacement is a $200 to $500 job at most shops. Ignoring it and damaging the catalytic converter can turn that into a $1,000 to $2,000 repair.
Frequently Asked Questions
Do I need to reprogram the computer after replacing the sensor?
No. The sensor itself does not need programming — it is a passive device that straightforward reads the crankshaft position and sends a signal. Once you install it and reconnect the battery, the engine computer will recognize it when ready. The check engine light may stay on for a few driving cycles while the computer relearns the sensor's signal, but no reprogramming is needed.
What if the new sensor does not fix the problem?
If the check engine light stays on after replacing the sensor and driving for 50 to 100 miles, the problem may be a wiring issue, a bad connector, or a problem with the engine computer itself. Have the code read at an auto parts store or shop to see what the computer is reporting. If the code is still a crank sensor code, the new sensor may not be seated correctly or the wiring may be damaged.
Can a crankshaft sensor go bad again right after replacement?
It is rare, but it can happen if the new sensor is defective or if there is a wiring problem that damaged the old sensor in the first place. If a sensor fails within a few weeks of replacement, the issue is usually a bad connector, corroded wiring, or a defective new part. Most sensors come with a warranty — check with the parts store or manufacturer if you suspect a defect.
Will a bad crankshaft sensor cause my car to fail an emissions test?
Yes. A failed crank sensor will trigger a check engine light, and most emissions tests will fail a car with an active check engine light. You must have the sensor replaced and the light cleared before the car will pass. Some states allow you to clear the light and drive for a certain number of miles before retesting, but the sensor must be fixed either way.