What a CKP sensor does and why it fails

Your crankshaft position (CKP) sensor tells your engine's computer where the crankshaft is at any given moment. The computer uses that signal to time the spark plugs and fuel injectors. When the CKP sensor fails, the engine cannot fire or inject fuel correctly, and you'll see a check engine light — usually code P0335, P0336, P0337, or P0338 depending on which part of the signal is broken.

CKP sensors fail because they sit near the crankshaft in a hot, vibrating environment. The sensor itself is a coil of wire wrapped around a magnet, and either the coil burns out or the magnet loses strength over time. Corrosion from engine heat and moisture can also damage the connector. Most sensors last 80,000 to 150,000 miles, but some fail much earlier if the engine runs hot or the sensor was installed incorrectly.

You can check a CKP sensor yourself with a multimeter and a basic understanding of how the sensor signal works. The test takes 15 to 30 minutes and costs nothing beyond the multimeter you may already own.

Key Takeaways

  • A CKP sensor produces an alternating voltage signal as the crankshaft rotates, and you can measure this signal with a multimeter set to AC volts.
  • The sensor connector usually has two or three wires: power (12 volts), ground, and signal; a broken wire or corroded connector will show zero or unstable voltage.
  • A good CKP sensor produces 0.3 to 1 volt AC while the engine cranks, and the signal should be steady without dropouts.
  • If the signal is weak or missing, the sensor itself is likely bad; if the signal is strong but the check engine light stays on, the wiring or connector may be the problem.
  • Replacing a CKP sensor usually costs $150 to $400 in labor and parts, depending on how accessible the sensor is on your engine.

Locate your CKP sensor and identify the connector

The CKP sensor bolts to the engine block near the crankshaft, usually on the front, rear, or side of the engine depending on your vehicle's design. Consult your owner's manual or a repair manual for your specific year, make, and model — the location varies widely. Some sensors are straightforward to reach; others require removing the wheel well liner, harmonic balancer, or timing cover.

Once you find the sensor, trace the wires back to the connector. The connector is usually a two- or three-pin plastic plug. Take a photo of the connector with your phone so you can reference the wire colors and pin positions while you work. Do not unplug the connector yet — you'll test the voltage while it's still connected.

Test the sensor signal with a multimeter

Set your multimeter to AC volts (not DC). This is important: CKP sensors produce an alternating voltage signal, and your multimeter must be set to read AC, not DC. If you set it to DC, you'll get a reading of zero even if the sensor is working.

Have a helper crank the engine while you hold the multimeter probes on the signal wire and ground wire of the connector. Do not unplug the connector — insert the probes through the back of the connector or carefully pierce the insulation of the wires with the probe tips. The signal wire is usually the middle pin or the wire labeled "signal" in your manual. Ground is the black or brown wire, or the pin connected to the engine block.

A working CKP sensor produces 0.3 to 1 volt AC while the engine cranks. The voltage should be steady and should not drop to zero during the crank. If you see 0 volts, the sensor is not producing a signal. If you see a voltage that jumps around or drops out, the sensor is failing intermittently. If you see voltage above 1 volt, the sensor may be too close to the crankshaft reluctor ring or the reluctor ring itself may be damaged.

Check the connector and wiring for damage

If the multimeter shows zero volts, the problem may not be the sensor itself — it could be a broken wire, a corroded connector, or a bad ground. Unplug the connector and inspect it for corrosion, bent pins, or cracks. Corrosion looks like white, green, or blue powder on the metal contacts. If you see corrosion, clean the connector with a wire brush or fine sandpaper, then plug it back in and test again.

Check the wires for cuts, pinches, or burn marks. Trace the wires from the sensor all the way to the engine computer (usually mounted on the firewall or under the hood). If a wire is damaged, you can splice it with a butt connector and solder, or replace the entire wiring harness if the damage is severe.

Test the ground connection by setting your multimeter to ohms (resistance) and touching one probe to the ground pin of the connector and the other probe to a clean metal part of the engine block. You should see zero or very low resistance (under 1 ohm). If you see high resistance or infinity, the ground wire is broken or corroded.

Verify the power supply to the sensor

CKP sensors need 12 volts of power to operate. Set your multimeter to DC volts and test the power wire of the connector while the ignition is on (engine off). You should see 12 volts. If you see less than 11 volts or zero, the power wire is broken or the fuse is blown.

Check the fuse box under the hood for a fuse labeled "CKP" or "crankshaft sensor." The fuse location and amperage vary by vehicle — your owner's manual will tell you which fuse to check. A blown fuse will have a broken wire visible inside the glass tube. If the fuse is blown, replace it with a fuse of the same amperage. If it blows again when ready, there is a short circuit in the wiring and you should stop testing and take the vehicle to a mechanic.

Interpret your test results and next steps

If the multimeter shows 0.3 to 1 volt AC while cranking and the power and ground are good, the sensor is working. The check engine light may be caused by something else, or it may clear after you drive the vehicle for a few miles. If the light stays on, you may need to clear the code with a scan tool and see if it returns.

If the multimeter shows zero volts AC and the power and ground are good, the sensor is bad and needs to be replaced. If the power or ground is missing, repair the wiring or connector first and retest. If the voltage is unstable or drops out during cranking, the sensor is failing and should be replaced soon — it may leave you stranded.

Replacing a CKP sensor usually costs $150 to $400 in parts and labor, depending on how accessible the sensor is. Some sensors bolt on in 10 minutes; others require removing the harmonic balancer or timing cover, which can take an hour or more. If you are not comfortable working on your engine, a mechanic can do the test and replacement for you.

Frequently Asked Questions

Can a bad CKP sensor cause the engine to not start?

Yes. Without a crankshaft position signal, the engine computer cannot fire the spark plugs or inject fuel, so the engine will crank but not start. A bad CKP sensor is one of the most common causes of a no-start condition. If your engine cranks but will not fire, a CKP sensor test should be one of your first checks.

What if my multimeter shows AC voltage but the engine still won't start?

The sensor may be producing a signal, but the signal may be too weak or too noisy for the computer to read. The computer may also be ignoring the signal if the wiring is intermittently broken. Have a mechanic scan the vehicle with a professional diagnostic tool to see if the computer is actually receiving and using the CKP signal, or if it is seeing errors in the signal.

Do I need to disconnect the battery before testing the CKP sensor?

No. You can test the CKP sensor with the battery connected and the ignition on. However, do not touch the multimeter probes to each other or to the engine block while the ignition is on, because you could create a short circuit. Keep the probes away from moving engine parts while someone cranks the engine.

Can a CKP sensor go bad gradually, or does it fail all at once?

Both. Some sensors fail suddenly and leave you stranded. Others degrade slowly, producing a weak or intermittent signal that causes rough idle, stalling, or a check engine light that comes and goes. If your multimeter shows a weak signal (under 0.3 volts), the sensor is likely failing and should be replaced soon.

What is the difference between a CKP sensor and a camshaft position sensor?

A CKP sensor monitors the crankshaft, which controls when the pistons move. A camshaft position (CMP) sensor monitors the camshaft, which controls when the valves open and close. Both sensors send signals to the engine computer, and both can cause a check engine light if they fail. They are separate components and are tested the same way with a multimeter.