What a crank position sensor does and why it fails
A crank position sensor (also called a crankshaft position sensor) tells your engine's computer where the crankshaft is at any given moment. The computer uses this information to time the spark plugs and fuel injectors correctly. Without an accurate signal, your engine will not start, will run rough, or will stall without warning.
The sensor sits near the crankshaft, usually on the front, side, or rear of the engine block depending on your vehicle's design. It reads a toothed ring or reluctor wheel attached to the crankshaft as it spins. Over time, the sensor's internal electronics wear out, or the connector corrodes, and the signal becomes unreliable or stops altogether.
Common failure signs include a check engine light (often code P0335 or P0336), a no-start condition, rough idle, stalling while driving, or poor fuel economy. If you see these symptoms, a crank sensor is a likely culprit — though a mechanic should confirm with a diagnostic scan before you replace it.
Key Takeaways
- A crank position sensor tells your engine computer where the crankshaft is so it can time ignition and fuel injection correctly.
- Replacement usually takes one to three hours and costs between $150 and $400 in parts and labor at a shop, though the sensor itself often runs $50 to $150.
- You will need basic hand tools (socket set, wrenches, screwdrivers), a jack and jack stands if the sensor is underneath, and your vehicle's service manual to locate it and find the correct torque specs.
- The sensor bolts or clips in place with one or two fasteners and has a single electrical connector; disconnecting the battery before you start prevents accidental short circuits.
- After installation, the check engine light may stay on until you drive the vehicle for a few miles so the computer can relearn the sensor signal.
Locating the sensor on your vehicle
The crank position sensor location varies widely by make, model, and year. On some vehicles it is easily visible on the front of the engine block. On others it sits behind the crankshaft pulley, under the intake manifold, or low on the side of the block near the oil pan — requiring you to lift the vehicle and remove other components to reach it.
Your best resource is the service manual for your specific vehicle. You can find a manual through the manufacturer's website, a repair database like AllData or Mitchell1, or a free resource like YourMechanic's DIY guides. The manual will show you exactly where the sensor is, what fasteners hold it, and the correct torque specification when you reinstall it.
If you do not have a manual, search online for "[your year, make, model] crank position sensor location" along with "DIY" or "replacement." Forums and YouTube channels dedicated to your vehicle often show the exact steps and any tricks to make the job easier.
Tools and parts you will need
Gather these items before you start: a socket set and wrenches that fit your vehicle's fasteners, screwdrivers (both Phillips and flathead), a jack and jack stands if you need to lift the vehicle, a flashlight or work light, and your service manual or printed instructions. Some sensors require a special removal tool, though most bolt or clip in with standard fasteners.
You will also need the replacement sensor itself. Buy the correct part number for your vehicle — do not guess. A sensor for the wrong model year or engine type will not work. Order from a parts store, online retailer, or the dealership. OEM (original equipment manufacturer) sensors are more expensive but often more reliable than aftermarket alternatives; many shops and DIYers split the difference by buying a mid-range brand with good reviews.
Have a small container or bag ready to hold the bolt or clip you remove, so you do not lose it. If the sensor has a connector with a locking tab, note how it releases before you pull it apart — some require you to squeeze a tab, others slide out, and forcing the wrong direction can break the connector.
Disconnecting the battery and removing the old sensor
Start by disconnecting the negative terminal of your battery. This prevents accidental short circuits or airbag deployment if you bump something while working. Loosen the nut on the negative post with a wrench, slide the cable off, and set it aside where it cannot touch the post again.
Locate the sensor connector and unplug it by releasing the locking tab or clip (check your manual or the connector itself for the release method). Take a photo of the connector orientation with your phone so you remember which way it goes back in. Some connectors are keyed so they only fit one way, but others are not.
Remove the bolt or clip holding the sensor in place using the appropriate socket or wrench. On some vehicles there is one fastener; on others there are two. Keep the fastener in a safe place. Gently pull the sensor straight out of its bore. If it is stuck, do not force it — spray a small amount of penetrating oil around the base and wait a few minutes, then try again. Forcing a stuck sensor can break the connector or damage the bore.
Installing the new sensor and reconnecting
Before you insert the new sensor, inspect the bore for debris, corrosion, or damage. Wipe it clean with a dry cloth. If the bore looks corroded or damaged, you may need to have it professionally cleaned or repaired — a damaged bore can cause the new sensor to fail quickly.
Insert the new sensor straight into the bore until it seats fully. Install the bolt or clip and tighten it to the torque specification in your service manual. Do not over-tighten; most crank sensors torque to between 6 and 25 foot-pounds depending on the vehicle. Over-tightening can crack the sensor body or strip the threads.
Reconnect the electrical connector, making sure it clicks or locks into place. Reconnect the negative battery terminal and tighten the nut securely. Start the engine and listen for any unusual sounds. The check engine light may remain on for a short time; this is normal. Drive the vehicle for 10 to 20 miles at varying speeds so the engine computer can relearn the sensor signal and turn the light off on its own.
When to stop and call a professional
If the sensor is located in a spot that requires removing the intake manifold, timing cover, or other major components, the job becomes significantly more complex. If you are not comfortable with those steps, a shop can do the work faster and with less risk of damaging other parts.
If the old sensor is severely corroded or stuck and will not come out without excessive force, stop and take the vehicle to a shop. Forcing it can damage the threaded bore, which then requires machine shop repair or engine block replacement — a much costlier fix.
If the check engine light stays on after 50 miles of driving, or if the engine still does not start or runs rough after replacement, the problem may not be the sensor itself. Have the vehicle scanned with a diagnostic tool to read the fault code. A different component — the wiring, connector, or engine computer — may be the real issue.
Cost and time expectations
At a repair shop, crank sensor replacement typically costs between $150 and $400 total. The sensor itself runs $50 to $150 depending on whether you choose OEM or aftermarket, and labor usually adds $100 to $300 depending on how accessible the sensor is on your vehicle. If the sensor is straightforward to reach, expect one to two hours of labor. If it requires removing other components, the job can take three to four hours.
Doing the work yourself saves the labor cost but requires the right tools, a safe workspace, and time to do it carefully. If you already own a basic socket set and jack, your out-of-pocket cost is just the sensor itself. If you need to buy tools, factor that into your decision.
Frequently Asked Questions
Can I drive with a bad crank position sensor?
Not safely. A failing sensor will cause the engine to stall, misfire, or not start at all. If you are stranded, you can sometimes limp to a repair shop at very low speed, but the engine may cut out without warning. Have it towed rather than risk a breakdown in traffic.
Will the check engine light turn off by itself after I replace the sensor?
Usually, yes. After you install the new sensor and reconnect the battery, drive the vehicle for 10 to 20 miles at varying speeds. The engine computer will relearn the sensor signal and clear the light on its own. If the light stays on after 50 miles, have the vehicle scanned to see if a different fault code has appeared.
What is the difference between OEM and aftermarket crank sensors?
OEM sensors are made by the vehicle manufacturer and are usually more expensive but carry a longer warranty and tend to last longer. Aftermarket sensors are made by third-party suppliers and cost less but vary in quality. Mid-range aftermarket brands often offer a good balance of price and reliability; avoid the cheapest options if you can.
Do I need to clear the fault code myself, or will it clear on its own?
The code will clear on its own after the computer relearns the sensor signal, which usually takes 10 to 50 miles of driving. You do not need a scan tool to clear it manually. If the light stays on after that, the code may indicate a different problem, and you should have it scanned by a shop.
What if the sensor keeps failing after I replace it?
Repeated failures usually point to a wiring problem, a corroded connector, or a damaged bore. Have a shop inspect the wiring harness and connector for corrosion or damage. If the bore is damaged, it may need professional repair. A failing engine computer can also cause the new sensor to be rejected, though this is rare.