What a crankshaft position sensor does and why it fails

A crankshaft position sensor tells your engine's computer where the crankshaft is in its rotation at any given moment. The engine uses this information to time the spark plugs and fuel injectors correctly. Without an accurate signal, your engine cannot run properly — it may stall, hesitate, misfire, or not start at all.

These sensors fail because they wear out over time or because the wiring corrodes. Some fail suddenly; others send weak signals that get worse gradually. A failing sensor usually triggers a check engine light and produces a diagnostic code like P0335 (crankshaft position sensor malfunction) that a code reader can detect.

Replacement is a straightforward job on many vehicles, though the location and difficulty vary widely. On some cars the sensor sits in an straightforward-to-reach spot near the crankshaft pulley; on others it is buried deep in the engine bay or mounted inside the timing cover.

Key Takeaways

  • A crankshaft position sensor failure triggers a check engine light and prevents the engine from running correctly, so replacement is necessary rather than optional.
  • The sensor itself costs between $50 and $300 depending on the vehicle, but labor can range from one hour to four hours depending on where it sits.
  • You will need a socket set, a code reader to confirm the diagnosis, and sometimes a special sensor socket or removal tool specific to your vehicle.
  • Disconnecting the battery before you start prevents electrical damage and is required on most vehicles before removing any sensor.
  • If the sensor is buried in the engine bay or requires timing adjustment after installation, a shop may be the faster and safer choice.

Confirm the diagnosis with a code reader

Before you buy a sensor or start taking things apart, read the diagnostic trouble code from your engine computer. You can borrow or rent a code reader from most auto parts stores for free or a small fee. Plug it into the diagnostic port under the steering column, turn the key to the "on" position without starting the engine, and retrieve the code.

Codes in the P0335 to P0340 range point to the crankshaft position sensor or its wiring. Codes like P0336 (sensor range/performance) or P0337 (sensor low voltage) narrow it down further. Write down the exact code — it helps you find the right sensor for your vehicle and tells a mechanic what you have already checked.

If you see a different code, the problem may be wiring, a connector, or something else entirely. A shop can pull the code for you if you do not have access to a reader, usually for no charge.

Locate the sensor on your vehicle

The crankshaft position sensor location depends entirely on your make, model, and year. On some vehicles it bolts to the front of the engine block near the crankshaft pulley. On others it mounts inside the timing cover, which means removing the cover to access it. A few sit near the transmission bell housing or on the back of the engine.

Look up the exact location in your vehicle's service manual or search online for "[your year, make, model] crankshaft position sensor location." YouTube videos for your specific vehicle often show the job step by step. If the sensor is buried or requires removing major components like the timing cover, intake manifold, or alternator, consider whether the job is worth doing yourself.

Once you know where it is, check whether you need any special tools. Some sensors require a removal socket that grips the sensor body without damaging it. Others need a torque wrench to install correctly. Your parts supplier can tell you what tools are necessary when you buy the sensor.

Remove the old sensor and install the new one

Disconnect the negative battery terminal first. This prevents accidental short circuits and protects the engine computer. Wait a few minutes for residual power to drain from the system.

Unplug the electrical connector from the sensor by pressing the release tab or clip. Some connectors are tight; gently wiggle the connector side to side as you pull. Do not yank on the wires themselves.

Remove the bolt or bolts holding the sensor in place using the correct socket size. On some vehicles the sensor unscrews by hand once the bolt is out. On others you will need to pull it straight out or use a removal tool. Keep the bolt in a safe place — you will need it to install the new sensor.

Before you install the new sensor, check whether it has a rubber O-ring or gasket. If it does, leave it in place. If the old sensor left behind a rubber ring, remove it and discard it. Install the new sensor in the same position and orientation as the old one, hand-tighten the bolt first, then torque it to the specification in your manual (usually between 20 and 30 foot-pounds). Reconnect the electrical connector until you hear or feel it click.

Reconnect the negative battery terminal. Start the engine and listen for any unusual sounds. The check engine light should go out within a few driving cycles if the sensor was the problem. If the light stays on, the wiring may be damaged or the sensor may be faulty.

When to take it to a shop instead

If the sensor is mounted inside the timing cover or requires removing the intake manifold, alternator, or other major components, a shop can usually do the job faster and with less risk of breaking something else. Labor costs at a shop typically range from $150 to $400 depending on location and difficulty, plus the cost of the sensor itself.

You should also consider a shop if you do not have a code reader to confirm the diagnosis, if you are not comfortable working on your engine, or if you do not have the special tools the job requires. A misdiagnosis or a sensor installed incorrectly can leave you stranded.

Many shops will read your code for free and tell you upfront whether the job is straightforward or complex on your vehicle. That conversation takes 15 minutes and can save you hours of frustration.

What to expect after replacement

The check engine light may not turn off when ready after you install the new sensor. The engine computer needs to run through its self-test cycle, which usually happens over the next few driving cycles (typically 50 to 100 miles of mixed driving). If the light is still on after a week of normal driving, read the code again to see whether it is the same code or a different one.

If the same code returns, the new sensor may be faulty, the wiring may be damaged, or the connector may not be fully seated. Unplug the connector, look inside for bent pins or corrosion, and push it back in firmly. If the connector looks clean and the code persists, the sensor may be defective and should be exchanged under warranty.

If a different code appears, the problem was not the crankshaft position sensor. A shop can help you diagnose the new code.

Frequently Asked Questions

How much does a crankshaft position sensor cost?

The sensor itself typically costs between $50 and $300 depending on whether it is an OEM part from the manufacturer or an aftermarket replacement. OEM parts are usually more expensive but are may provide to fit. Aftermarket sensors are cheaper and often work just as well, but quality varies by brand. Ask your parts supplier which brands have good reviews for your vehicle.

Can a bad crankshaft position sensor damage the engine?

A failing sensor will not damage the engine itself, but it will prevent the engine from running correctly or at all. If you drive on a sensor that is sending weak signals, the engine may misfire or run rough, which can damage the catalytic converter over time. Replace the sensor as soon as the code appears to avoid that risk.

Do I need to clear the check engine light after I replace the sensor?

No. The light will turn off on its own once the engine computer confirms the sensor is working correctly. If you clear the code manually with a code reader before the sensor is actually fixed, the light will come back on within a few driving cycles. Let the computer do the work.

What if the new sensor has the same code as the old one?

The new sensor may be faulty, the wiring may be damaged, or the connector may not be fully seated. Check the connector for bent pins or corrosion, push it in firmly, and read the code again. If the code persists, the sensor is likely defective and should be exchanged. If a different code appears after that, the problem is elsewhere in the ignition or fuel system.