What a crank angle sensor does and why it fails
A crank angle sensor (also called a crankshaft position sensor) tells your engine's computer where the crankshaft is in its rotation at any given moment. The computer uses this information to time the spark plugs and fuel injectors correctly. Without an accurate signal, your engine cannot run properly — it may not start at all, or it may run rough and trigger a check engine light.
The sensor sits near the crankshaft, usually mounted on the engine block or timing cover, and reads a toothed wheel or magnetic ring as it spins. Over time, sensors fail because of heat exposure, vibration, oil contamination, or straightforward age. Most last between 80,000 and 200,000 miles, though the range varies by vehicle and sensor design.
Key Takeaways
- A crank angle sensor failure prevents the engine from starting or causes rough running and a check engine light.
- Replacement cost ranges from $150 to $400 in parts and labor, depending on sensor location and your vehicle model.
- The sensor is usually accessible without removing major engine components, but some vehicles require more disassembly than others.
- You will need a socket set, screwdrivers, and possibly a diagnostic scanner to confirm the sensor is the problem before you replace it.
- A faulty sensor can damage the catalytic converter if left unrepaired, so address a confirmed failure promptly.
Symptoms that point to a crank angle sensor problem
The most common sign is a check engine light paired with a specific code — typically P0335 (crankshaft position sensor malfunction) or similar. You may also notice the engine cranks but will not start, or starts and stalls when ready. Some vehicles run very rough at idle or lose power under acceleration.
These symptoms overlap with other electrical and fuel system problems, so do not assume the sensor is bad without confirmation. A diagnostic scanner that reads engine codes will show you whether the sensor itself is reporting an error or whether the problem lies elsewhere. Many auto parts stores will scan your vehicle for free and tell you which code is stored.
How to locate and access the sensor on your vehicle
The crank angle sensor location varies widely. On some vehicles it bolts to the front of the engine block near the crankshaft pulley. On others it sits inside the distributor, on the timing cover, or near the oil pan. Your vehicle's service manual or a repair database like AllData or Haynes will show the exact location and any components you need to remove to reach it.
Common obstacles include the serpentine belt, engine covers, and the crankshaft pulley itself. Some vehicles require you to remove the right front wheel and inner fender liner to access the sensor. Others sit in plain view once you open the hood. The time and difficulty range from 15 minutes on an accessible sensor to two hours or more if the sensor is buried under other parts.
Step-by-step replacement process
Start by disconnecting the negative battery terminal to prevent electrical shorts. Locate the sensor and trace its wiring harness back to the connector. Unplug the connector — it usually has a small tab you press to release it. Take a photo of the connector orientation before you disconnect it, so you know which way to plug in the new sensor.
Remove the bolt or bolts holding the sensor in place. Most sensors use a single 10mm or 13mm bolt, though some use two. Carefully pull the sensor straight out of its mounting hole. Do not force it; if it is stuck, explore penetrating oil and wait a few minutes. Install the new sensor by reversing the steps: insert it into the hole, thread the bolt by hand first to avoid cross-threading, then tighten it snugly — do not over-tighten, as the mounting boss can crack.
Reconnect the wiring harness, making sure the connector clicks into place. Reconnect the negative battery terminal. Start the engine and see if the check engine light clears. If the light remains on after a few driving cycles, the problem may not have been the sensor, or a second fault may be present.
Tools and parts you will need
You will need a socket set (typically 10mm and 13mm sockets), a ratchet, screwdrivers (both Phillips and flat-head), and possibly a wrench set if your vehicle uses bolts instead of sockets. A jack and jack stands are necessary if you need to remove a wheel to access the sensor. A diagnostic scanner is not required to replace the sensor, but having one lets you confirm the fault code before you buy parts and start work.
The replacement sensor itself costs between $40 and $150 depending on your vehicle make and model. OEM (original equipment manufacturer) sensors are more expensive than aftermarket alternatives but often carry longer warranties. Check your vehicle's year, make, model, and engine size when ordering, as the same part number does not fit all vehicles.
When to replace versus when to test further
If your diagnostic scanner shows a crank angle sensor code, replacement is usually the right move. However, a faulty wiring harness, corroded connector, or damaged wiring can trigger the same code. Before you replace the sensor, inspect the connector for corrosion or loose pins, and check the wiring for cuts or damage. If the connector looks corroded, clean it with electrical contact cleaner and try starting the engine again.
If the code returns after cleaning, or if the wiring is visibly damaged, the sensor itself is likely at fault. Some repair shops will test the sensor's resistance with a multimeter before replacing it, though this test is not always conclusive. If you are uncertain, replacing the sensor is usually faster and cheaper than extensive electrical diagnosis.
Labor costs if you take it to a shop
A shop will typically charge between $150 and $400 total for sensor replacement, depending on location difficulty and local labor rates. Shops in urban areas and dealerships tend to charge more than independent mechanics. If the sensor is straightforward to reach, you may pay only $100 to $150 in labor plus the part cost. If the sensor requires removing the crankshaft pulley, timing cover, or other major components, labor can exceed $300.
Getting a quote before you authorize work is standard practice. Ask the shop whether they will test the sensor or connector before replacing it, and whether they will clear the check engine code after the repair. Some shops charge an additional diagnostic fee if you did not bring a code reading with you.
Frequently Asked Questions
Can I drive with a bad crank angle sensor?
Not safely. A faulty sensor will cause the engine to stall, misfire, or fail to start. Driving on a bad sensor risks stalling in traffic or at an intersection. Additionally, a sensor that sends wrong timing signals can damage the catalytic converter over time, leading to a much more expensive repair.
Will replacing the sensor clear the check engine light automatically?
The light should turn off after a few driving cycles once the sensor is replaced and working correctly. If the light remains on, the problem may not have been the sensor, or a second fault code may be present. You can clear the code manually with a diagnostic scanner, but the light will return if the underlying problem is not fixed.
What is the difference between OEM and aftermarket sensors?
OEM sensors are made by your vehicle's manufacturer and typically cost more but carry longer warranties. Aftermarket sensors are made by third-party suppliers and cost less, but quality varies. Both types work in most cases. Check reviews for your specific vehicle before choosing an aftermarket part.
Do I need to replace the wiring harness if the sensor is bad?
Usually no. The harness itself rarely fails unless it is visibly damaged or corroded. If the connector looks clean and the wiring is intact, replacing the sensor alone will solve the problem. Inspect the connector before you buy parts.
How long does a new sensor last?
Most crank angle sensors last between 80,000 and 200,000 miles. Lifespan depends on engine heat, vibration, and how well the engine is maintained. A sensor that fails much sooner than expected may indicate a deeper problem, such as excessive engine heat or oil contamination.