Camshaft replacement typically costs between $800 and $2,500 for a single camshaft, or $1,500 to $4,000 if both intake and exhaust camshafts need replacement

The final bill depends on three things: which camshaft failed, whether your engine has one or two per bank, and how much labour your mechanic charges per hour. A four-cylinder engine with one camshaft per bank costs less to replace than a V6 or V8 with two camshafts per bank. Labour usually runs $500 to $1,500 because the mechanic has to remove the timing belt or chain, the valve cover, and sometimes the cylinder head itself to reach the camshaft.

Parts cost varies widely. A new OEM (original equipment manufacturer) camshaft runs $300 to $800 depending on the engine. Aftermarket camshafts cost $150 to $400. A remanufactured camshaft—one that has been cleaned, inspected, and resurfaced—costs $200 to $500 and is often a sensible middle ground. You will also pay for a new timing belt or chain if yours is due, new gaskets and seals, and sometimes new rocker arms or followers if they were damaged alongside the camshaft.

Key Takeaways

  • Labour makes up 60 to 70 percent of the total cost because the mechanic must disassemble the top of the engine to reach the camshaft.
  • A remanufactured camshaft costs less than a new OEM part and carries a warranty, making it a practical choice for many owners.
  • If your timing belt is near the end of its service life, replacing it at the same time prevents a second expensive repair within months.
  • Camshaft failure usually happens because oil starvation damaged the lobes, so the underlying cause—a clogged filter, low oil level, or failed pump—must be fixed or the new camshaft will fail the same way.

Why labour is the largest part of the bill

Reaching a camshaft means taking apart the engine's top end. The mechanic removes the valve cover, then the timing belt or chain that synchronises the camshaft to the crankshaft. On many engines, the cylinder head itself must come off. This is not a 30-minute job—it typically takes 4 to 8 hours depending on engine design and how much corrosion or seized bolts the mechanic encounters.

Shop labour rates vary by region and shop type. Independent shops charge $75 to $150 per hour. Dealerships charge $120 to $200 per hour. A 6-hour job at an independent shop costs $450 to $900 in labour alone. The same job at a dealership costs $720 to $1,200. This is why getting a quote from your actual mechanic matters far more than a general range.

Parts: new, remanufactured, or aftermarket

An OEM camshaft from the manufacturer carries a full warranty and is may provide to match your engine's specifications exactly. It costs the most—typically $400 to $800—but you know it will work. A remanufactured camshaft has been removed from a donor engine, cleaned, inspected under magnification, and the lobes resurfaced to factory dimensions. It costs $200 to $500 and usually carries a 12-month or 12,000-mile warranty. Aftermarket camshafts, made by third-party manufacturers, cost $150 to $400 but warranties vary and some are shorter or more limited.

Beyond the camshaft itself, you will pay for new gaskets and seals around the valve cover and cylinder head—typically $50 to $150. If the timing belt is being replaced at the same time, add $200 to $600 depending on engine size. If rocker arms, followers, or the timing chain were damaged, those parts add another $200 to $800. A new oil filter and fresh oil are standard—$30 to $75.

Single versus dual camshaft engines

A single-cam engine has one camshaft per cylinder bank and costs less to repair because there is only one shaft to replace and fewer components to remove. A dual-overhead-cam (DOHC) engine has two camshafts per bank—one for intake valves, one for exhaust—and sometimes both fail at once or within months of each other. If only one has failed, you might replace just that one now and plan for the second later. If both are damaged, the total parts cost doubles, though labour increases only slightly because the mechanic is already inside the engine.

V6 and V8 engines have two banks, so a V6 can have two, four, or six camshafts depending on design. A V8 can have four, eight, or sixteen. Knowing your engine's configuration helps you understand why your quote is higher or lower than a friend's—their four-cylinder with one camshaft will always cost less than your V8 with eight.

Why the underlying cause matters to your wallet

Camshafts fail almost always because of oil starvation. The lobes—the egg-shaped protrusions that push the valves open—rely on a constant film of oil to prevent metal-to-metal contact. When oil pressure drops, the lobes wear rapidly and eventually break or score. If your mechanic finds a failed camshaft but does not fix what caused the oil starvation, the new camshaft will fail the same way within months.

Common causes include a clogged oil filter, low oil level from a slow leak, a failed oil pump, or sludge buildup from infrequent oil changes. Your mechanic should inspect the oil system before reassembling the engine. If the oil pump is failing, replacing it now costs $300 to $800 extra but prevents a second $2,000 repair. If the filter was clogged, that is a $20 fix. If sludge is present, a flush and fresh oil are essential. Skipping this step is false economy.

Timing belt replacement and camshaft work

The timing belt or chain synchronises the camshaft to the crankshaft. When a mechanic removes it to access the camshaft, they see its condition up close. If the belt is cracked, frayed, or near the end of its service life—typically 60,000 to 100,000 miles depending on the engine—replacing it now costs less than replacing it later. The labour is already paid for because the engine is already apart.

Delaying a timing belt replacement is risky. If it breaks while you are driving, the camshaft and crankshaft fall out of sync, valves collide with pistons, and you face a $3,000 to $5,000 engine rebuild. Replacing the belt at the same time as the camshaft adds $200 to $600 to your bill but eliminates that risk. Most mechanics recommend this approach, and most owners find it sensible when they understand the alternative.

Getting an accurate quote from your mechanic

A quote should list the camshaft (OEM, remanufactured, or aftermarket), labour hours, gaskets and seals, any other parts being replaced, and the shop's hourly rate. Ask whether the timing belt or chain will be inspected and whether replacement is recommended. Ask what warranty covers the camshaft and the labour. Ask whether the oil system will be inspected for the cause of failure.

If the quote seems high, get a second one from another shop. Prices vary, and so do shop reputations. A shop that charges more per hour but finishes faster and stands behind the work may cost less overall than one that charges less per hour but takes longer or has a poor warranty. Read reviews and ask whether the shop has experience with your specific engine—some engines are notoriously difficult to work on, and a shop familiar with yours will quote more accurately.

Frequently Asked Questions

Can I drive with a failed camshaft?

No. A broken or severely worn camshaft prevents the valves from opening and closing properly, which causes misfires, loss of power, and rough running. Continuing to drive risks damage to the cylinder head, pistons, or valves. Stop driving and have it towed to a mechanic.

Is a remanufactured camshaft as good as a new one?

Yes, if it comes from a reputable remanufacturer. The lobes are resurfaced to factory dimensions and inspected under magnification. Most carry a 12-month warranty. The main difference is cost—remanufactured parts cost 40 to 50 percent less than OEM parts.

How long does camshaft replacement take?

Typically 4 to 8 hours depending on engine design, accessibility, and whether the cylinder head must be removed. Some engines are easier to work on than others. Ask your mechanic for a time estimate specific to your vehicle.

Will my check engine light go off after replacement?

Yes, once the new camshaft is installed and the engine runs normally, the light should clear. If it stays on, the mechanic should scan the codes again to identify any remaining issues before you leave.

What if both camshafts failed at the same time?

Replace both. The labour cost increases only slightly because the engine is already apart, but the parts cost doubles. This usually happens when oil starvation was severe, so inspect the oil system carefully to prevent it happening again.