The firing order for a small block 350 Chevy is 1-8-4-3-6-5-7-2

This sequence tells you which cylinder fires next in the engine's combustion cycle. The numbers represent the physical location of each cylinder in the engine block, and the order ensures that power strokes happen in a balanced rhythm that keeps the engine running smoothly. If your firing order is wrong — because you've pulled spark plug wires or replaced ignition components — your engine will run rough, misfire, or not start at all.

The small block 350 is one of the most common V8 engines in American vehicles, and its firing order has stayed consistent across decades of production. Whether you're working on a 1970s Chevrolet, a 1980s Camaro, or a later model truck, this sequence applies. Knowing it is essential if you're doing any work on the ignition system, spark plugs, or distributor cap.

Key Takeaways

  • The firing order 1-8-4-3-6-5-7-2 is the correct sequence for all small block 350 engines, and it applies whether your engine has a points distributor, an HEI distributor, or a modern electronic ignition system.
  • Cylinder numbering on a small block 350 runs 1-2-3-4 on the driver's side (front to back) and 5-6-7-8 on the passenger side (front to back).
  • If you pull spark plug wires or the distributor cap, photograph or label each wire before removal so you can reinstall them in the correct firing order.
  • A wrong firing order causes misfires, rough idle, hard starting, and poor fuel economy — symptoms that often point to ignition timing or spark plug problems first.

How cylinder numbering works on the small block 350

The small block 350 is a V8 with eight cylinders arranged in two banks. The driver's side (left bank) holds cylinders 1, 2, 3, and 4, numbered from front to back. The passenger side (right bank) holds cylinders 5, 6, 7, and 8, also numbered front to back. This layout is standard across Chevrolet small block engines and is the same whether your engine is in a car, truck, or marine process.

When you look at the engine from the front, the driver's side is on your left and the passenger side is on your right. Cylinder 1 is at the very front of the driver's side, and cylinder 8 is at the very back of the passenger side. Knowing this layout helps you locate each spark plug and understand why the firing order moves the way it does — it's designed to balance the load across both banks of cylinders.

Why firing order matters for engine performance

The firing order controls the timing of combustion in each cylinder. If cylinders fire in the wrong sequence, the engine develops vibration, loses power, and runs unevenly. A misaligned firing order can also cause the engine to pull to one side under acceleration because power is being delivered unevenly to the crankshaft.

The 1-8-4-3-6-5-7-2 sequence was engineered to spread power strokes evenly across the crankshaft rotation. Each cylinder fires once every two complete revolutions of the crankshaft (720 degrees). The order ensures that no two adjacent cylinders fire in quick succession, which would create a shock load on the crankshaft. This balanced sequence is why the small block 350 became such a reliable, durable engine.

Reinstalling spark plug wires in the correct order

The most common mistake happens when someone pulls the spark plug wires without labeling them first. The wires must go back on in firing order, connected to the correct terminal on the distributor cap. If you pull the wires, use a marker or tape to number each wire before you remove it, or take a photo of the cap with the wires still attached.

The distributor cap has eight terminals arranged in a circle. The terminal for cylinder 1 is usually marked on the cap itself — often with a notch, a line, or a number. Once you locate cylinder 1, you can mark the other terminals by following the firing order clockwise or counterclockwise around the cap, depending on your distributor's rotation direction. Most small block 350 distributors rotate clockwise, but verify this before you reinstall the wires.

If you're unsure which direction your distributor rotates, check your engine's service manual or look at the rotor inside the cap — it points to the terminal that is currently firing. As the engine runs, the rotor spins in the direction of distributor rotation. Reinstall the wires in firing order following that direction.

Distributor cap and rotor replacement

When you replace the distributor cap or rotor, the firing order remains the same, but you need to make sure the new cap is installed in the same rotational position as the old one. The cap usually has a notch or alignment mark that fits into a corresponding slot on the distributor body. If you rotate the cap even slightly, the firing order will be wrong and the engine won't start.

Before you remove the old cap, mark the position of the rotor with a marker or tape on the distributor body. When you install the new cap, align the rotor to that same mark. This ensures that cylinder 1 still fires at the correct terminal. If you've already removed the cap and lost track of the rotor position, you can set it by turning the engine to top dead center on cylinder 1 — the rotor should point to the cylinder 1 terminal on the cap.

Checking firing order if your engine misfires or won't start

If your small block 350 is misfiring, running rough, or won't start, a wrong firing order is one of the first things to check. Pull the distributor cap and inspect the spark plug wires. Trace each wire from the cap to its spark plug and verify that it matches the firing order sequence. A single wire in the wrong position will cause a misfire in that cylinder.

Also check that the wires are seated firmly on both the distributor cap terminal and the spark plug. A loose connection can cause an intermittent misfire that feels like a timing or fuel problem. If all the wires are in the correct order and seated properly, the issue is likely elsewhere — bad spark plugs, a failing distributor, or a timing problem.

Frequently Asked Questions

What happens if I install the spark plug wires in the wrong order?

The engine will misfire, run rough, and may not start at all. Each cylinder will fire at the wrong time in the combustion cycle, creating vibration and power loss. The engine may also backfire through the carburetor or exhaust. Correcting the wire order usually fixes the problem when ready.

Does the firing order change if I upgrade to an electronic ignition system?

No. The firing order 1-8-4-3-6-5-7-2 remains the same regardless of whether you use a points distributor, an HEI distributor, or a modern electronic ignition module. The sequence is determined by the engine's mechanical design, not the ignition system type.

Can I find the firing order printed on my engine?

Some engines have the firing order stamped on the intake manifold or printed on a decal under the hood, but not all. Your engine's service manual or a Chevrolet small block reference guide will always have it. The firing order is also often printed on the distributor cap itself.

What if my distributor rotates counterclockwise instead of clockwise?

Some aftermarket or older distributors rotate counterclockwise. The firing order sequence stays the same, but you install the wires in reverse order around the cap — starting at cylinder 1 and moving counterclockwise instead of clockwise. Check your distributor's direction before you install the wires.

Do I need to reset the firing order if I replace the crankshaft or camshaft?

No. The firing order is built into the engine's design and does not change when you replace internal components. However, if you replace the distributor or ignition system, you must reinstall the spark plug wires in the correct firing order for that new component.