What motor mounts do and why they fail
Motor mounts are rubber-and-metal brackets that hold your engine to the frame and absorb vibration as it runs. Most vehicles have three to four of them — typically one on each side, one at the front, and sometimes one at the rear. When they wear out, the engine can shift excessively, causing clunking sounds, steering wheel vibration, or visible movement under the hood.
Mounts fail because the rubber degrades over time from heat, oil exposure, and constant flexing. A failed mount usually means replacement, not repair. The job ranges from straightforward on some vehicles to labor-intensive on others, depending on engine placement and what else is in the way.
Before you start, know that this is not a beginner job on most cars. You will be working under a running or recently-running engine, supporting it with a jack, and disconnecting engine components. If you are not comfortable with those tasks, a shop is the safer choice.
Key Takeaways
- Motor mounts hold the engine in place and absorb vibration; worn mounts cause clunking, rough idle, or visible engine movement.
- Replacing one mount usually takes two to four hours on accessible mounts, but some vehicles require removing other parts first, adding significant time.
- You will need a jack, jack stands, basic hand tools, and a way to support the engine weight while the mount is out.
- Many shops charge $300 to $800 per mount in labor alone, so the job is worth learning if you have the tools and space.
- Replacing all mounts at once costs more upfront but prevents repeat visits and ensures even engine support.
Identifying which mount is worn
A clunking sound when you shift from Drive to Reverse or accelerate hard often points to a front or side mount. A rhythmic vibration at idle suggests a rear mount. To narrow it down, have someone rev the engine while you watch from the side — a worn mount will let the engine rock visibly in the direction of the failed mount.
You can also inspect mounts visually. Crawl under the engine with a flashlight and look for cracks in the rubber, oil saturation (the rubber will look dark and soft), or metal-to-metal contact where the rubber has completely separated. If you see daylight between the rubber and the bracket, that mount is done.
Some vehicles have one mount that fails before others — usually the front or passenger-side mount, which takes the most load during acceleration. Check all of them while you are under there. If one is worn, the others are likely close behind.
Tools and materials you will need
At minimum: a floor jack, jack stands rated for your vehicle's weight, a socket set, wrenches, a breaker bar for stuck bolts, and a block of wood to protect the oil pan or frame when jacking. You will also need the replacement mounts themselves — order them before you start so you know the part numbers and can confirm fitment.
Some jobs require a engine support bar — a temporary brace that bolts to the engine and rests on the frame, holding the engine up while you remove the mount. This is not always necessary, but it is safer than relying on a jack alone. You can rent one from a tool rental shop or buy a universal one for $40 to $100.
Have a service manual for your vehicle on hand. It will show you which bolts to remove, the order to remove them, and the torque specs for reinstallation. Bolts installed too loose will rattle; too tight and you risk stripping threads or cracking the mount bracket.
The basic replacement process
Start by disconnecting the negative battery terminal to prevent accidental electrical shorts. Raise the vehicle on jack stands — never work under a car supported only by a jack. If you are replacing a side or front mount, you may need to remove the wheel, splash guard, or other components to reach it. Check your manual for the specific order.
Once you can see the mount, locate all bolts connecting it to the engine and frame. Some bolts go through the mount itself; others bolt the bracket to the engine or subframe. Support the engine with a jack placed under the oil pan (with a wood block between them) or with an engine support bar. Loosen the bolts gradually — do not remove one completely until the others are loose, or the engine will shift and jam the mount.
Remove the bolts in the order your manual specifies, then slide the old mount out. Clean the bolt holes and mounting surfaces with a wire brush to remove rust or debris. Install the new mount, hand-tighten all bolts first, then torque them to spec in a crisscross pattern — this ensures even pressure. Lower the engine carefully and remove the jack or support bar.
Reconnect the battery, start the engine, and listen for clunking. The engine should sit level and not rock excessively when you shift gears. If it still moves too much, you may have a second failed mount or an installation error.
Mounts that require removing other parts
On some vehicles — particularly transverse-engine front-wheel-drive cars — the passenger-side mount sits behind the engine, requiring you to remove the intake manifold, alternator, or power steering pump to reach it. On others, the subframe must come down partially. These jobs can add four to eight hours of labor.
Before you commit to a DIY replacement, look up the procedure for your specific year, make, and model. Search "[your vehicle] motor mount replacement" plus "how to" or "DIY" and read through forum posts or YouTube comments from people who have done it. They will tell you what surprised them and what tools they wish they had.
If the mount is buried behind major components, a shop is often the better choice. The labor cost may be high, but the risk of damaging other parts or spending a weekend on the job is real.
Torque specs and reinstallation
This is where most DIY replacements go wrong. Motor mount bolts are typically torqued to 35 to 65 foot-pounds, depending on the vehicle and bolt size — but the exact spec matters. Under-torqued bolts will loosen and rattle. Over-torqued bolts can crack the rubber or strip the threads in the engine block.
Use a torque wrench, not a ratchet and feel. Set it to the spec in your manual, tighten each bolt in a crisscross pattern (like tightening a wheel), and stop when the wrench clicks. If you do not have a torque wrench, borrow or rent one — they cost $20 to $50 and are worth it for this job.
After reinstalling, let the engine idle for a minute and watch for movement. Shift into Drive and Reverse a few times — the engine should barely rock. If it moves excessively or you hear clunking, stop and recheck your work. A bolt may have come loose, or the mount may be installed backwards (some mounts are directional).
When to replace all mounts at once
If one mount is worn, the others are under extra stress and likely to fail soon. Replacing all of them at once costs more upfront but saves you from repeating the job in six months. The labor time does not double — a shop replacing all four mounts might charge for five to six hours instead of two to four, because some of the setup and teardown is shared.
If you are doing the work yourself, replacing all mounts in one session makes sense from a time perspective. You are already under the car, the engine is already supported, and you will not have to repeat the hardest part of the job.
The exception is if only one mount is visibly failed and the others look solid. In that case, replace the bad one and inspect the others every six months. If they start to show cracks or oil saturation, plan to replace them soon.
Frequently Asked Questions
Can I drive with a bad motor mount?
Yes, but not safely for long. A failed mount lets the engine shift excessively, which can damage hoses, belts, and wiring. It also makes the car harder to control during hard acceleration or braking. Have it replaced within a few days.
How much does a motor mount replacement cost at a shop?
Parts typically cost $50 to $200 per mount. Labor ranges from $300 to $800 per mount depending on location and how accessible it is. A single replacement usually runs $400 to $1,000 total; replacing all mounts can cost $1,500 to $3,000.
What if I install the mount backwards?
Some mounts are directional and will not fit properly backwards. You will notice during installation — the bolt holes will not line up or the rubber will be compressed unevenly. Check the part number on the old mount against the new one to confirm they are the same, and look at the orientation before you remove the old one.
Do I need to replace the engine oil after removing a mount?
No, as long as you do not drain the pan or disconnect the oil filter. If you do accidentally drain oil or disturb the filter, top it off or replace the filter before starting the engine.
How long do new motor mounts last?
OEM mounts typically last 80,000 to 150,000 miles. Aftermarket mounts vary widely — some last as long as OEM parts, others fail sooner. Buy the best quality you can afford, and avoid the cheapest options online.