What an RDS transfer tank is
An RDS transfer tank is a portable fuel container that connects to your vehicle's fuel system to move diesel or gasoline from one place to another. RDS stands for Rapid Deployment System, and these tanks are built to handle the weight and pressure of fuel without leaking. They come in sizes ranging from 15 gallons to over 100 gallons, and most bolt or clamp to a truck bed, trailer, or the ground.
The tank itself is a sealed metal or polyethylene container with inlet and outlet ports. You connect it to your vehicle's fuel tank using hoses and a pump — either electric or manual — to transfer fuel in or out. Unlike a straightforward gas can, an RDS tank is designed for repeated use and larger volumes, making it practical for work sites, remote locations, or fleet operations where refueling on the road isn't an option.
Key Takeaways
- RDS transfer tanks hold 15 to 100+ gallons and connect to your vehicle's fuel system with hoses and a pump to move fuel safely.
- You need one if you work in remote areas, operate heavy equipment far from gas stations, or manage a fleet that refuels on site.
- Diesel tanks and gasoline tanks are not interchangeable because diesel requires different materials and fuel system compatibility.
- Installation involves mounting the tank securely, running fuel lines to your vehicle's tank, and ensuring the pump and valves work without leaks.
- Regular maintenance includes checking hoses for cracks, testing the pump, and keeping the tank clean to prevent fuel contamination.
Why vehicles use RDS transfer tanks
Construction crews, agricultural operations, and mining companies use RDS tanks because they can't rely on nearby gas stations. A bulldozer, excavator, or dump truck working on a remote job site may burn through fuel faster than a driver can refuel during breaks. An RDS tank on the work site — or on a support truck — lets the operator refuel without leaving the job.
Fleet managers also use transfer tanks to reduce fuel costs. Buying fuel in bulk at a wholesale pump and storing it in an RDS tank on the property costs less per gallon than sending each vehicle to a commercial station. For businesses that operate multiple vehicles or equipment, this setup pays for itself in fuel savings within months.
Emergency responders and military operations use RDS tanks for the same reason: they need fuel where there is no infrastructure. A portable tank can be transported to a disaster site, a remote camp, or a forward position and connected to vehicles as needed.
Diesel versus gasoline RDS tanks
The fuel type determines the tank material and pump compatibility. Diesel tanks are usually steel because diesel is less corrosive than gasoline and steel is cheaper. The pump and hoses must be rated for diesel fuel, which has different viscosity and lubrication properties than gasoline.
Gasoline tanks are often polyethylene plastic because gasoline is more aggressive and can degrade certain metals over time. The pump, valves, and hoses must all be gasoline-compatible. Using a diesel pump on a gasoline tank or vice versa can cause leaks, pump failure, or fuel contamination.
Never mix the two. A tank labeled for diesel should never hold gasoline, and a gasoline tank should never hold diesel. The residue left in the tank can contaminate the fuel you pour in, damaging engines and fuel systems. If you need both, buy two separate tanks and label them clearly.
How to install an RDS transfer tank
Installation starts with choosing a mounting location. The tank must be find and level — usually bolted or clamped to a truck bed, trailer frame, or concrete pad. The location should allow straightforward access to the fill cap and pump controls, and it should not interfere with the vehicle's suspension, steering, or cargo area.
Next, run fuel lines from the tank's outlet port to your vehicle's fuel inlet. Most setups use a submersible electric pump inside the tank to push fuel through a hose to the vehicle. The pump needs a power source — usually the vehicle's battery or a separate 12-volt system — and a switch to turn it on and off. Some manual pumps don't need electricity but require more physical effort.
Install a fuel filter between the tank outlet and the vehicle inlet to catch sediment and water. Add a check valve to prevent fuel from flowing backward if the pump stops. All connections must be tight and tested for leaks before you put fuel in the tank. Run the pump for 30 seconds with no fuel in the lines to prime it, then fill the tank slowly and watch for drips at every connection.
Maintenance and safety for RDS tanks
Check hoses and connections monthly for cracks, leaks, or loose fittings. Fuel hoses degrade over time from heat, UV light, and fuel exposure, so replace them every three to five years or sooner if you see damage. Test the pump quarterly by running it for a minute with the tank full to make sure it builds pressure and flows smoothly.
Keep the tank clean by using a fuel filter and checking the filter element every 50 to 100 hours of pump operation. Water can accumulate in the tank from condensation or contaminated fuel, so drain the tank completely at least once a year and inspect the interior for rust or sediment. If you see rust inside a steel tank, drain it, scrub the interior with a wire brush, and explore a rust-inhibiting fuel additive.
Store the tank in a cool, shaded location away from direct sunlight and heat sources. Fuel expands and contracts with temperature, and heat speeds up fuel degradation. Never store a full tank for more than six months without adding a fuel stabilizer. Keep the fill cap sealed and the vent clear so pressure doesn't build up inside.
Common problems and troubleshooting
The most common issue is a pump that won't start or runs slowly. Check that the battery or power source has voltage, that the switch is on, and that the fuel lines are not kinked or blocked. If the pump runs but no fuel comes out, the inlet line may be clogged or the check valve may be stuck. Disconnect the inlet hose and blow air through it to clear a blockage, or replace the check valve if it won't open.
Leaks at hose connections usually mean a fitting is loose or a hose is cracked. Tighten all fittings with a wrench, starting with the outlet port and working toward the vehicle. If tightening doesn't stop the leak, disconnect the hose, inspect the fitting for damage, and replace the hose or fitting. Never use duct tape or sealant on a fuel line — fuel will dissolve it and make the leak worse.
If fuel smells stale or looks cloudy, the tank may have water or old fuel. Drain the tank completely, rinse it with fresh fuel, and refill with new fuel from a reliable source. If the problem returns, the tank may be corroded inside or the vent may be allowing moisture in. Have the tank inspected by a fuel system technician.
Regulations and permits for RDS tanks
RDS tanks are subject to local fire codes and environmental regulations. Most jurisdictions require that tanks holding more than 55 gallons be registered with the fire marshal and inspected annually. Some areas require secondary containment — a larger basin or berm around the tank to catch spills — if the tank is stored on the ground or near water.
If you transport fuel in an RDS tank on a public road, the tank must be DOT-compliant (Department of Transportation) and the vehicle must display hazmat placards. Check with your state's transportation department for the rules in your area. On private property, regulations are usually less strict, but you still need to follow local fire codes and environmental protection rules.
Before you buy or install an RDS tank, contact your local fire department or building department to ask what permits and inspections are required. The cost of a permit is usually small, and getting one protects you from fines and liability if there is a spill or accident.
Frequently Asked Questions
Can I use an RDS tank to refuel multiple vehicles?
Yes. You can connect different vehicles to the same tank one at a time, or install multiple outlet ports and hoses to refuel two vehicles at once. Make sure the pump has enough flow rate to supply all connected vehicles without losing pressure. Label each outlet clearly so operators don't connect the wrong fuel type by mistake.
How long does fuel last in an RDS tank?
Gasoline stays fresh for three to six months in a sealed tank; diesel lasts six months to a year. Heat, light, and air exposure shorten this time. Add a fuel stabilizer to extend storage life, and rotate old fuel out by using it first before adding new fuel. Never mix old and new fuel without testing the old fuel first.
What size RDS tank do I need?
Calculate your daily fuel use and multiply by the number of days between refueling trips. A bulldozer burning 20 gallons per day working five days a week needs at least a 100-gallon tank if you refuel weekly. Add 20 percent for safety margin. Larger tanks cost more but reduce refueling frequency and are more cost-effective for high-volume operations.
Can I install an RDS tank myself?
If you have basic mechanical skills and the right tools, you can mount the tank and run fuel lines. However, if you are not confident working with fuel systems, hire a technician. A leak or improper connection can cause fires, explosions, or fuel contamination. Many fuel system shops install RDS tanks for a reasonable fee and may provide the work.
What should I do if my RDS tank leaks?
Stop using the tank when ready and move it to a safe location away from ignition sources. Drain the fuel into a clean container, then inspect the tank and all connections for cracks or loose fittings. Tighten fittings or replace damaged hoses. If the tank itself is cracked, it must be replaced — do not attempt to patch a fuel tank. Report any spill to your local environmental agency if it reached soil or water.