The Bobcat 942607 uses part number 6693498 as its primary engine air filter

The Bobcat 942607 is a compact track loader, and its engine air filter is one of the most important maintenance items you can replace yourself. The correct part number is 6693498, which is Bobcat's OEM (original equipment manufacturer) filter for this model. This filter prevents dirt, dust, and debris from entering the engine, where they would cause wear on pistons, rings, and valve seats—damage that costs thousands to repair.

Replacing this filter is straightforward enough that most owners can do it without special tools. The job takes 10 to 15 minutes and costs far less than the engine damage that happens when you run the machine on a clogged or missing filter. You do not need a mechanic or a lift; you just need the correct part number and a basic understanding of where the filter housing sits on your machine.

Key Takeaways

  • The correct OEM air filter for the Bobcat 942607 is part number 6693498, available from Bobcat dealers and aftermarket suppliers.
  • A clogged air filter reduces engine power, increases fuel consumption, and allows dirt to enter the engine if it ruptures or leaks around the seal.
  • You can replace the filter yourself by locating the air filter housing on top of or to the side of the engine, unbolting the cover, and sliding out the old filter.
  • Check your filter every 50 operating hours in dusty conditions and replace it when you see visible dirt buildup or when the machine loses power.
  • Aftermarket filters meeting the same size and flow specifications work, but OEM filters are engineered to fit your exact machine and are worth the cost.

Where the air filter housing is located on the 942607

On the Bobcat 942607, the air filter housing is mounted on top of or directly beside the engine, depending on your machine's configuration and year. The housing is a cylindrical or rectangular plastic or metal container with a large bolt or clip holding the cover on. You will see it when ready when you open the engine compartment or look at the top of the engine from the side.

The housing sits between the air intake and the carburetor or fuel injection system. If you trace the large rubber hose coming from the engine, it leads to the filter housing. The cover is usually held down by a single large bolt, a wing nut, or a spring clip—nothing that requires a wrench larger than a half-inch socket or a basic adjustable wrench.

Steps to remove and replace the filter

Start by shutting off the engine and letting it cool for at least five minutes. A warm engine is not dangerous, but a cool one is easier to work on and you will not burn your hands on hot metal.

Locate the bolt or clip holding the filter cover in place. If it is a bolt, use your socket wrench or adjustable wrench to turn it counterclockwise until it comes free. If it is a clip or wing nut, turn it by hand. Do not force it; if it is stuck, spray a little penetrating oil and wait a minute. Once the fastener is loose, lift the cover straight up and set it aside on a clean surface.

The old filter will slide out of the housing. It may be dusty, so tap it gently against the inside of the housing to dislodge loose dirt before you pull it out completely. Do not blow compressed air into the housing or shake the filter hard—you want to avoid sending dust into the engine or the carburetor opening.

Before you install the new filter, wipe the inside of the housing with a clean, dry cloth. Remove any dirt, leaves, or debris that has settled at the bottom. This takes 30 seconds and prevents contamination from reaching the engine.

Slide the new filter (part number 6693498) into the housing. It will fit only one way—the rubber seal or gasket on the filter sits against the housing wall. Push it in until it seats firmly but do not force it. Replace the cover and tighten the bolt or clip by hand first, then use your wrench to snug it down. It should be tight enough that it will not rattle, but you do not need to crank it with all your strength.

How to know when your filter needs replacing

The most reliable signal is a loss of engine power or a rough idle. When the filter clogs, the engine cannot draw enough air, and it runs lean—meaning the fuel mixture is too rich. You will notice the machine feels sluggish, especially under load, or the engine sounds different than usual.

A visual inspection is also useful. Remove the cover and look at the filter. If you see a thick layer of dust, dirt, or debris coating the pleats, it is time to replace it. In clean conditions, a filter might last 200 or more operating hours. In dusty conditions—construction sites, sandy terrain, dry fields—it can clog in 50 to 100 hours. Check it every 50 hours if you work in dust, and every 100 to 150 hours in normal conditions.

Never run the machine with the filter cover off or with a torn filter. A torn filter allows unfiltered air and dirt straight into the engine, and running without a filter at all is like pouring sand into your fuel tank. The damage happens fast and is not covered by warranty.

OEM versus aftermarket filters for the 942607

Bobcat part number 6693498 is the OEM filter, made to Bobcat's specifications and tested to fit your exact machine. It costs more than a generic aftermarket filter, but it is engineered for the 942607's airflow requirements and seal dimensions. You know it will fit and perform as the manufacturer intended.

Aftermarket filters that meet the same size and flow rating (usually listed in microns and cubic feet per minute) will work, but you are taking a small risk. A filter that is slightly undersized may not seal properly, allowing dirt to bypass it. One that is oversized may not fit in the housing or may restrict airflow too much. If you choose an aftermarket filter, verify the part dimensions and flow specifications against the OEM filter before you buy.

For most owners, the OEM filter is the safer choice. The cost difference is usually $20 to $40, and it eliminates guesswork. You can order it from any Bobcat dealer or from online equipment suppliers that stock genuine Bobcat parts.

What happens if you ignore a clogged filter

A clogged filter forces the engine to work harder to pull air through the blockage. Fuel consumption rises, and the engine runs hotter because it is not getting the cooling effect of a full air charge. Over time, the filter material can tear or separate from its frame, allowing unfiltered dirt to enter the engine directly.

Once dirt reaches the cylinders, it acts like an abrasive. It scratches the cylinder walls, wears the piston rings, and damages the valve seats. This wear is cumulative and irreversible. You may not notice it for hundreds of hours, but eventually the engine will lose compression, burn oil, and fail. A new or rebuilt engine for a Bobcat 942607 costs $3,000 to $5,000 or more. A $50 air filter replacement every 100 hours is cheap insurance against that bill.

Frequently Asked Questions

Can I clean and reuse the old filter instead of replacing it?

No. Air filters are designed to be replaced, not cleaned. Tapping out loose dust is fine, but washing or blowing out a filter damages the pleats and degrades the media. A cleaned filter will not seal properly and will allow dirt to bypass it. Replace it with a new one.

What if I cannot find part number 6693498?

Contact a Bobcat dealer directly—they can order it for you and usually have it in stock or can get it within a few days. If you need it urgently, ask the dealer for an equivalent aftermarket part that meets the same specifications. Never run the machine without a filter while you wait.

Do I need to replace the filter housing cover gasket when I replace the filter?

Only if it is cracked, hardened, or no longer seals. Most gaskets last for many filter changes. If you remove the cover and the gasket looks dry or brittle, or if air leaks around the cover after you install a new filter, replace the gasket at the same time.

How tight should I make the cover bolt?

Snug it down firmly by hand with your wrench, then give it a quarter turn more. It should not rattle or move when you tap on it, but you should not need a lot of force. Over-tightening can crack the plastic housing or strip the bolt threads.

Can I use a different Bobcat filter part number if it fits?

No. Different Bobcat models use different filter housings and airflow requirements. Using the wrong part number may result in a poor seal, incorrect filtration, or physical interference with other engine components. Always use part number 6693498 for the 942607.