The cab air filter on a Kubota B2230 is located inside the climate control unit and takes about 15 to 20 minutes to replace once you access it
The B2230's cab air filter cleans the air flowing through your heating and air conditioning system. Unlike the engine air filter, which sits in an external housing, the cab filter lives inside the dashboard assembly behind the glove box. You will need to remove the glove box to reach it, but the job requires no special tools beyond a screwdriver and takes less than half an hour.
Replacing it yourself costs the price of the filter part only — typically $30 to $60 depending on the filter type and supplier. A dealer service call for the same work runs $100 to $150 in labor alone. The filter itself does not wear out on a schedule; you replace it when airflow through the vents drops noticeably or when you see visible dust and debris inside the filter housing.
Key Takeaways
- The cab air filter sits behind the glove box in the dashboard, not under the hood with the engine filter.
- Removal requires taking out the glove box with a screwdriver, then unclipping or unbolting the filter housing from inside the cavity.
- Kubota part number HH1G0-33110 is the OEM cab air filter for the B2230, though aftermarket filters from Fram and other suppliers fit the same housing.
- You will know the filter needs replacement when air from the vents feels weak or when you see dust caked on the filter surface.
Locating the cab air filter housing
Open the glove box door and look at the right side of the compartment (the side toward the door). You will see a small bolt or clip holding the glove box hinge to the dashboard frame. Remove that fastener — usually a single 10mm bolt or a spring clip — and the glove box will swing down and out of the way.
Once the glove box is clear, look up into the cavity. The filter housing is a rectangular plastic box mounted horizontally above where the glove box sat. It will have a seam running around its perimeter where the top and bottom halves meet. Some housings are held in place with two bolts on the sides; others use clips that you press inward to release.
Removing the old filter
If your housing uses bolts, remove them with a socket or wrench. If it uses clips, press them inward from the sides and the housing will separate. Once the housing is loose, gently pull the bottom half down and away from the top half. The old filter will be sitting inside, usually held in place by friction or a light clip.
Slide the old filter out. You may see a rubber gasket or foam seal around the edge of the filter; if it is stuck to the housing, peel it off gently and discard it with the filter. Look inside the housing for any loose debris — leaves, dust, or dirt — and wipe it out with a dry cloth or compressed air. Do not use a wet cloth, as moisture can damage the housing seals.
Installing the new filter
Check the part number on your new filter to confirm it matches Kubota HH1G0-33110 or your specific model's equivalent. The filter has an arrow printed on one side indicating airflow direction; this arrow should point toward the cabin (away from the engine side of the housing).
Slide the new filter into the housing with the arrow pointing the correct direction. If your filter came with a new gasket or seal, press it onto the filter edge now. Align the top and bottom halves of the housing and press them together until they click or seat fully. If the housing uses bolts, reinstall them and tighten them snugly — do not over-tighten, as the plastic housing can crack.
Reinstalling the glove box
Swing the glove box back up into its opening and align the hinge with the bolt hole or clip on the dashboard. Reinstall the fastener and tighten it. Open and close the glove box a few times to confirm it moves freely and closes completely.
Turn on the cab climate control and listen for any rattling or unusual noise from the dashboard. If you hear nothing and the air flows normally through the vents, the job is complete. If airflow is still weak, the new filter may not be seated correctly; open the glove box again and confirm the housing halves are fully pressed together.
When to replace the cab air filter
The cab filter does not have a fixed service interval like the engine air filter. Instead, replace it when you notice reduced airflow from the heating or air conditioning vents, or when you see a visible layer of dust and debris on the filter surface when you open the housing. In dusty conditions — such as working in dry fields or on unpaved roads — you may need to replace it once or twice per season. In normal use, many operators go a full year or more between replacements.
If you run the B2230 in a particularly dusty environment, inspect the filter every 50 hours of operation. A clogged cab filter makes the climate control system work harder and can reduce cooling or heating effectiveness. Replacing it before it becomes completely blocked keeps the cabin comfortable and reduces strain on the HVAC blower motor.
Frequently Asked Questions
Can I clean and reuse the old cab air filter instead of replacing it?
Some cab filters can be cleaned with compressed air to extend their life by a few weeks, but they cannot be restored to full effectiveness. Once a filter is visibly dirty, replacement is more cost-effective than cleaning. The filter itself costs $30 to $60, and the time to clean it is nearly the same as the time to install a new one.
What is the difference between the cab air filter and the engine air filter?
The engine air filter cleans air going into the engine for combustion and sits in a housing under the hood. The cab air filter cleans air flowing through the heating and air conditioning system inside the cabin. They are separate components with different part numbers and replacement schedules.
Do I need to buy the OEM Kubota filter or can I use an aftermarket one?
Aftermarket filters from Fram, Bosch, and other suppliers fit the B2230 cab filter housing and perform the same function. They cost slightly less than the OEM part and are widely available. Either choice is acceptable; the important thing is matching the filter size and shape to your housing.
What happens if I drive with a completely clogged cab filter?
A severely clogged filter reduces airflow through the vents, making it harder to heat or cool the cabin. The blower motor will run harder to push air through the blockage, which can shorten its lifespan. You will also notice dust and odors inside the cab. Replacing the filter restores normal operation.