Where the cabin filter sits and what it does

The cabin filter in your Lexus NX 300 is located behind the glove box on the passenger side. It traps dust, pollen, and other particles from outside air before that air enters the cabin through your vents and climate control system. A clogged cabin filter reduces airflow, makes your air conditioning and heating less effective, and can cause musty odors inside the vehicle.

Lexus recommends checking your cabin filter every 15,000 miles and replacing it every 30,000 miles, though this varies depending on driving conditions. If you drive in dusty or high-pollen areas, you may need to replace it more often. A dirty filter will look gray or brown instead of white, and you may notice reduced air output from your vents.

Key Takeaways

  • The cabin filter is behind the glove box on the passenger side and takes about 10 to 15 minutes to replace yourself.
  • You will need a replacement filter (part number 87139-02100 for most NX 300 models) and a Phillips screwdriver or socket wrench.
  • Removing the glove box requires unbolting two or three fasteners and disconnecting the damper rod that prevents it from falling.
  • The filter slides straight out and in, with arrows on the frame showing the correct direction of airflow.

Tools and parts you need

You will need a replacement cabin filter designed for the Lexus NX 300. The OEM Lexus part number is 87139-02100, though aftermarket filters from brands like Mann-Filter, Bosch, and Fram also fit. A genuine Lexus filter costs between $25 and $40, while aftermarket options typically run $15 to $25.

For tools, gather a Phillips screwdriver or a 10mm socket wrench (depending on your model year), and a flashlight or headlamp to see inside the glove box cavity. You do not need any special equipment or a lift. The entire job can be done in your driveway.

How to remove the glove box

Open the glove box fully and look underneath the top edge. You will see two bolts on the underside of the glove box frame. Remove both using your Phillips screwdriver or 10mm socket. On some model years, there is a third bolt on the right side of the box near the hinge.

Next, locate the damper rod — a small hydraulic arm that prevents the glove box from falling open. It connects to the top of the glove box with a clip or ball joint. Gently pull or pry this connection free. The glove box will now pull straight out toward you. Set it aside on a clean surface so you do not lose any small parts.

Locating and removing the old filter

With the glove box removed, shine your flashlight into the cavity. You will see a rectangular plastic frame holding the cabin filter. The frame is usually held in place by friction or by two small clips on the sides. Look for arrows printed on the frame showing the direction of airflow — these point toward the cabin, not toward the outside.

Slide the filter frame straight out toward you. It should come free without force. If it is stuck, check that you have released any clips. Once out, you can slide the filter itself out of the frame, or straightforward replace the entire frame if your new filter comes in one.

Installing the new filter

Before sliding the new filter in, check that the airflow arrows on the frame point toward the cabin (away from the engine compartment). Slide the filter straight into the cavity until it seats fully. You should hear or feel a slight click as it locks into place, depending on your model year.

If you removed just the filter and kept the frame, make sure the frame sits flat and level inside the cavity. Misaligned filters can rattle or allow unfiltered air to bypass the sides.

Reinstalling the glove box

Reconnect the damper rod to the top of the glove box first. Push the clip or ball joint back into its socket until it clicks. Then slide the glove box back into the dashboard opening, aligning the bolt holes. Install the two or three bolts you removed earlier, tightening them snugly but not forcefully — over-tightening can crack the plastic frame.

Close the glove box and open it again to confirm it moves smoothly and the damper rod works. If the box feels stiff or the damper does not slow its descent, check that the rod is fully seated.

When to replace your cabin filter

Lexus recommends a cabin filter replacement every 30,000 miles under normal driving conditions. If you live in a dusty climate, drive on unpaved roads frequently, or notice reduced airflow or odors before 30,000 miles, replace it sooner. Some owners in high-pollen areas replace theirs every 15,000 to 20,000 miles.

You can also inspect the filter yourself by removing the glove box and looking at the frame. If the filter surface is visibly clogged with dust or debris, it is time to replace it regardless of mileage.

Frequently Asked Questions

Can I drive with a dirty cabin filter?

Yes, but your air conditioning and heating will work less effectively, and you may smell stale or musty air in the cabin. A very clogged filter can also put extra strain on your climate control blower motor over time.

What if I put the filter in backward?

The airflow arrows on the frame prevent this — the filter will not seat properly if reversed. If you force it in backward, you will feel resistance and the frame will not sit flush. straightforward remove it, flip it, and reinstall it correctly.

Do I need to replace the glove box frame too?

No. The frame is reusable. You only replace the filter material inside it. If the frame cracks or the clips break, you can order a replacement frame separately, but this is rare.

Is there a cabin filter on the driver's side too?

No. The Lexus NX 300 has one cabin filter located behind the passenger-side glove box. It filters all air entering the cabin regardless of which vents you use.

What is the difference between OEM and aftermarket cabin filters?

OEM Lexus filters are made to exact factory specifications and typically cost more. Aftermarket filters from established brands like Bosch and Mann-Filter fit the same way and perform similarly, often at a lower price. Both are safe to use.