Removing the seats from your 2014 Honda Odyssey Touring is straightforward if you know where the bolts are and what tools you need
The 2014 Honda Odyssey Touring has seats that bolt directly to the floor. To remove any seat, you'll unbolt it from underneath, disconnect the electrical connectors if it's a power seat, and lift it out. The job takes about 15 to 30 minutes per seat and requires basic hand tools. Most owners do this to clean underneath, repair the seat frame, replace upholstery, or make room for cargo or a wheelchair lift.
Before you start, disconnect the negative terminal on your battery. This prevents accidental airbag deployment if you're working near the seat frame or electrical connections. Then move the seat all the way forward or backward—whichever gives you the best access to the bolts you need to remove.
Key Takeaways
- The 2014 Odyssey Touring seats bolt to the floor with four bolts per seat, located at the front and rear of the seat base.
- Power seats have electrical connectors underneath that must be unplugged before you lift the seat out.
- You will need a socket wrench set, a Phillips screwdriver, and possibly a trim removal tool to access some connectors.
- Disconnecting the battery before you start prevents accidental airbag deployment and electrical shorts.
- The captain's chairs in the second row are easier to remove than the bench seat, which is heavier and requires more space to maneuver.
Tools and materials you'll need
Gather these items before you start: a socket wrench set (you'll use 12mm and 14mm sockets most often), a Phillips screwdriver, a trim removal tool or flat-head screwdriver for prying plastic covers, and a clean workspace or towel to set bolts on so you don't lose them. If your Odyssey has power seats, you may also need a small flashlight to see the electrical connectors clearly underneath the seat.
A helper is useful but not essential. Seats are heavy—the captain's chairs weigh around 40 to 50 pounds each, and the bench seat is heavier—so having someone stabilize the seat while you unbolt it reduces the risk of dropping it or straining your back. If you're working alone, clear a wide path and have a safe place to set the seat down when ready after you lift it free.
Removing the front captain's chairs
Start with the front passenger seat because it's easier to access than the driver's seat. Move the seat all the way back, then look underneath. You'll see four bolts: two at the front of the seat base and two at the rear. Use your socket wrench to remove all four bolts. They're usually 12mm or 14mm, and they should come off without much resistance—if one is stuck, spray it with penetrating oil and wait a few minutes.
Once the bolts are out, check underneath the seat for electrical connectors. On a power seat, you'll see a plug with wires running to the seat frame. Pinch the connector clip and pull straight down to disconnect it. Some connectors have a small tab you press to release them. If you're unsure, take a photo with your phone before you disconnect anything so you can match it up when you reinstall the seat.
Now lift the seat straight up and out. Tilt it slightly if it catches on the door frame or steering wheel. Set it on a clean surface where it won't get damaged. Repeat this process for the driver's seat, but be aware that the driver's seat may have additional wiring for lumbar support or seat memory functions—disconnect all of these before lifting.
Removing the second-row captain's chairs
The second-row captain's chairs follow the same pattern as the front seats. Move each chair all the way forward, then locate the four bolts underneath. Remove them with your socket wrench. Check for electrical connectors—second-row seats typically have power recline and sometimes power lumbar support, so you may have two or three connectors to unplug.
These seats are lighter than the front seats and easier to maneuver in the cabin. Lift straight up and set them aside. If you're removing both captain's chairs, you'll have a large open space in the second row, which is why many owners do this when they need to transport large items or install a wheelchair lift.
Removing the third-row bench seat
The third-row bench seat is heavier and more awkward to remove than the captain's chairs. It bolts to the floor at four points, just like the other seats, but the rear of the seat also has a hinge mechanism that connects to the floor. Move the seat forward as far as it will go, then remove the four floor bolts using your socket wrench.
Next, look at the rear hinge. You'll see bolts or clips holding the hinge to the floor. Remove these as well. Once all bolts are out, disconnect any electrical connectors for power recline or lumbar support. The bench seat is now free, but it's heavy and awkward—recruit a helper to lift it straight up and out. Tilt it as needed to clear the doorway and the second-row seats.
Reconnecting power and reinstalling seats
When you're ready to put the seats back, reverse the process. Reconnect all electrical connectors first, making sure each one clicks into place. Then position the seat in the opening and lower it onto the floor bolts. Hand-thread each bolt a few turns to make sure you're not cross-threading, then tighten them with your socket wrench. Tighten in a crisscross pattern—front left, rear right, front right, rear left—so the seat sits evenly.
After all seats are back in place and bolted down, reconnect the negative battery terminal. Start the engine and test the power seat functions if your Odyssey has them. Move each seat forward, backward, up, and down to confirm everything works. Check that the seat is stable and doesn't rock or shift when you push on it.
Why you might need to remove seats
Owners remove Odyssey seats for several reasons. Deep cleaning underneath is the most common—the space under the seats collects crumbs, spills, and debris that are hard to reach with a vacuum. Removing the seats lets you clean the floor and the underside of the seat frame thoroughly.
Seat frame repair is another reason. If the frame is cracked or the hinge mechanism is broken, you may need to remove the seat to access the damaged part. Upholstery replacement—recovering torn or stained fabric—also requires removing the seat so the upholsterer can work on it properly. Some owners remove seats to install aftermarket equipment like wheelchair lifts, additional storage, or custom seating configurations.
Common problems and how to avoid them
The most frequent issue is cross-threading a bolt when you reinstall the seat. To avoid this, hand-thread each bolt several turns before using the socket wrench. If you feel resistance, stop and back the bolt out—you've likely started it at an angle. Start again slowly.
Another problem is forgetting to reconnect an electrical connector. Before you close the door and drive away, test all power functions on every seat you removed. If a seat won't move or recline, you likely missed a connector. Lift the seat again and check underneath.
Dropping a bolt into the gap between the seat and the floor is straightforward to do. Keep bolts in a small container or on a magnetic tray as you remove them. If you do drop one, use a flashlight and a magnet on a stick to retrieve it before you reinstall the seat.
Frequently Asked Questions
Do I have to disconnect the battery before removing seats?
Disconnecting the battery is not strictly required for seat removal, but it's a good safety practice. It prevents accidental airbag deployment if you bump a connector or electrical contact while working underneath the seat. It takes two minutes and costs nothing, so it's worth doing.
Can I remove just one seat, or do I have to remove all of them?
You can remove one seat at a time. Each seat is independent, so removing the driver's seat doesn't affect the passenger seat or the second row. Remove only what you need to.
What size are the seat bolts on a 2014 Odyssey Touring?
Most seat bolts are 12mm or 14mm. Have both sizes in your socket set before you start. If a bolt doesn't fit, try the other size. Forcing the wrong socket onto a bolt can strip it.
How much do replacement seats cost if I damage one during removal?
OEM replacement seats for a 2014 Odyssey Touring range widely depending on whether you buy a used seat from a salvage yard or a new one from Honda. Used seats typically cost $200 to $400 per seat; new seats cost $800 to $1,500 or more. Careful handling during removal prevents this expense.
Is it normal for the seat to be heavy and hard to lift?
Yes. Front and second-row captain's chairs weigh 40 to 50 pounds each, and the third-row bench is heavier. This is normal. Use your legs, not your back, when lifting, and don't hesitate to ask for help. A dropped seat can cause injury or damage to the vehicle interior.