What you're replacing and why it matters
The grille insert on your 2015 Jeep Renegade Limited is the open square mesh panel that sits in the center of the front grille. It's a visible part of the front end, and damage to it — whether from road debris, a minor collision, or just age — shows when ready. Replacing it is one of the simpler cosmetic repairs you can do yourself, and a new insert costs between $40 and $120 depending on the supplier and whether you choose OEM (original equipment manufacturer) or aftermarket.
The job requires no special tools beyond what most people have in a basic toolkit. You'll need a Phillips head screwdriver, possibly a trim removal tool to help with clips, and about 30 minutes of your time. The insert itself snaps or bolts into the existing grille frame, so you're not replacing the whole grille — just the visible front piece.
Key Takeaways
- The grille insert is the square mesh panel in the center front of your Renegade, held in by clips or bolts on the sides and top.
- You can remove the old insert by unbolting or unclipping it from the grille frame without removing the entire grille from the vehicle.
- OEM inserts from Jeep dealers cost more but match the original exactly; aftermarket versions are cheaper and often identical in fit.
- The whole job takes about 30 minutes and requires only a Phillips screwdriver and possibly a plastic trim tool.
- Check whether your specific insert uses bolts or clips before you start, as this changes the removal method slightly.
Identifying the correct replacement part
The 2015 Jeep Renegade Limited uses a specific grille insert that differs slightly from other trim levels. The Limited model has a chrome-trimmed insert with a particular mesh pattern. Before you order a replacement, confirm you have the Limited trim — if you have the Sport or Latitude, the insert may look similar but the fitment can be different.
You have two sourcing options. Jeep dealerships sell OEM inserts under part number 68303990AA (for the Limited trim). This is the exact part that came on your vehicle. Online retailers like RockAuto, Amazon, and eBay carry both OEM and aftermarket versions, often at lower prices. Aftermarket inserts from brands like Rugged Ridge or Omix-ADA fit the same way and look nearly identical, though some buyers prefer OEM for exact color matching. Take a photo of your current insert and compare it to the product photo before ordering.
Removing the old insert
Start by opening your hood and looking at how the insert attaches to the grille frame. On most 2015 Renegades, the insert is held by two bolts on the left and right sides (where the insert meets the grille frame) and clips along the top edge. Some models use only clips. If you see bolt heads, use your Phillips screwdriver to remove them first — they're usually 10mm or Phillips head, and they won't be tight.
Once the side bolts are out, gently pull the top of the insert toward you. The clips should release with light pressure. If they resist, use a plastic trim removal tool or the flat end of a screwdriver to gently pry the clips free from underneath. Don't force it — the clips are plastic and will break if you pull too hard. Work your way across the top, releasing each clip as you go. The insert should come free in your hands.
Set the old insert aside. Look at the grille frame where the insert was attached. You should see the bolt holes clearly and the clip slots along the top. Wipe away any dirt or debris from these areas before installing the new insert.
Installing the new insert
Position the new insert in front of the grille frame, aligning the bolt holes on the sides with the holes in the frame. The insert should sit flush with the grille — if it's sitting crooked, the clips won't engage properly. Start by inserting the top edge of the insert into the clip slots along the top of the grille frame. Push gently until you hear or feel a click — the clips should snap into place.
Once the top clips are seated, align the side bolt holes and insert the bolts. Tighten them by hand first, then use your screwdriver to snug them down. Don't over-tighten — these bolts are small and the grille frame is plastic. Hand-tight plus a quarter turn is usually enough. Step back and check that the insert sits evenly in the frame with no gaps or tilting.
Checking your work
Close your hood and look at the grille from the front. The insert should sit flush with the grille frame all the way around, with no gaps at the top, sides, or bottom. If you see a gap, open the hood again and check that all clips are fully seated and bolts are snug. The insert should not move or rattle when you gently push on it.
If the insert is sitting crooked, remove it and check the clip slots and bolt holes for debris or damage. Sometimes a small piece of plastic or dirt can prevent proper seating. Clean the frame and try again. If a clip is broken, you may need to order a new insert — clips cannot be repaired.
When to call a shop instead
If your grille frame itself is cracked or bent, replacing just the insert won't fix the problem. The frame holds the insert in place, so a damaged frame will cause the new insert to sit unevenly or rattle. In that case, you'll need the entire grille assembly replaced, which is a larger job. A shop can do this in an hour or two, and the cost depends on whether you use OEM or aftermarket parts.
If you remove the insert and find that the bolt holes are stripped (the bolts spin without tightening), the frame is damaged and will need replacement. This is rare but can happen if the previous insert was over-tightened or if the vehicle was in an accident. A dealership or independent shop can assess the damage and quote you for a new grille frame.
Frequently Asked Questions
Can I use a grille insert from a different Jeep model?
No. The 2015 Renegade's insert is specific to that model and year. Inserts from other Jeeps like the Wrangler or Cherokee have different dimensions and won't fit the Renegade's grille frame. Stick with parts listed for the 2015 Renegade Limited specifically.
What if I can't find the bolts or clips?
Some inserts use only clips, others use bolts and clips. If you don't see bolts, the insert is held entirely by clips along the top and sides. Look carefully along the top edge and the left and right sides where the insert meets the frame. The clips are usually small plastic tabs that you push or pull to release.
Will an aftermarket insert look different from the original?
Most aftermarket inserts are made to match the OEM design closely, but some have slightly different mesh patterns or chrome finishes. Check the product photos carefully before ordering. If exact color matching is important to you, order OEM from a Jeep dealer.
Do I need to remove the entire grille to replace the insert?
No. The insert comes out separately from the grille frame. You only remove the insert itself, which takes about 30 minutes. Removing the entire grille is a much larger job that requires disconnecting the radiator and other components.
What should I do if the new insert doesn't fit?
Double-check that you ordered the correct part for the 2015 Renegade Limited. Verify the part number matches. If the insert is the right part but still doesn't fit, the grille frame may be bent or damaged. Take a photo and contact the seller to confirm fitment, or have a shop inspect the frame.