What a rear door lock actuator does and when it fails
The rear door lock actuator on your 2019 Mercedes Sprinter 2500 is a small electric motor that moves the lock mechanism when you press the power lock button or use the key fob. When it fails, the rear doors won't lock or unlock from the inside or outside, even though the front doors work fine. You might hear a clicking sound when you try to lock the doors, or nothing happens at all.
A failed actuator usually means the motor inside has burned out or the internal gears have stripped. This is a common wear item on Sprinters, especially if the doors are used frequently or if moisture has gotten inside the mechanism. Replacing it is a straightforward job that takes about 30 to 45 minutes per door if you have basic mechanical skills and the right tools.
Key Takeaways
- The rear door lock actuator is a small electric motor mounted inside the door panel that controls the lock mechanism.
- You will need a door panel removal tool, a Phillips screwdriver, and the replacement actuator (part number varies by left or right door).
- The job involves removing the interior door panel, disconnecting the electrical connector, and unbolting the old actuator before installing the new one.
- A replacement actuator for a 2019 Sprinter 2500 costs between $80 and $150 depending on the supplier, plus labor if you take it to a shop.
Tools and parts you will need
Gather these items before you start. You will need a door panel removal tool (a plastic pry bar, not a metal screwdriver, which can crack the trim), a Phillips head screwdriver, a socket set with a 10mm socket, and a replacement lock actuator. Mercedes part numbers are different for the left and right rear doors, so confirm which door you are working on before ordering.
For a 2019 Sprinter 2500, the OEM part numbers are 9068200135 (left rear) and 9068200235 (right rear). Aftermarket actuators are available from parts suppliers and typically cost less than OEM parts. You may also want a trim panel clip removal tool if you do not have one, though the door panel removal tool can work in a pinch. Have a clean cloth or small container nearby to hold fasteners so you do not lose them.
Removing the interior door panel
Start by rolling down the window completely so it does not interfere with panel removal. On the 2019 Sprinter, the door panel is held by clips around the perimeter and a few bolts. Locate the bolt at the top of the door panel near the window frame and remove it with your 10mm socket. There is usually one bolt on the inside edge of the door, near the door latch.
Once the bolts are out, use your plastic door panel removal tool to gently pry the panel away from the door frame, starting at the bottom corner. Work your way around the perimeter, releasing the plastic clips as you go. The panel will come free once all clips are released. Set it aside carefully—the window regulator cable and lock rod are still attached to the back of the panel. Do not pull hard or you will damage these connections.
Disconnecting the lock actuator
With the door panel removed, you will see the lock actuator mounted on the inside of the door, usually near the lock mechanism. It is a small rectangular box with an electrical connector on one end and a rod or linkage connected to the lock. Locate the electrical connector and press the release tab to disconnect it. Some connectors have a small clip you must slide sideways to release.
Next, locate the bolts holding the actuator to the door frame. There are typically two bolts, one at the top and one at the bottom of the actuator housing. Remove both with your 10mm socket. Disconnect any linkage rods connected to the actuator by unclipping or unbolting them—these vary depending on the door configuration, so take a photo before you disconnect anything so you remember how it goes back together.
Installing the new actuator
Take the new actuator and position it in the same location as the old one. Insert the two mounting bolts and tighten them firmly with your 10mm socket, but do not overtighten—you can crack the plastic housing. Reconnect any linkage rods to the new actuator, making sure they are seated fully in their clips or bolt holes. Reconnect the electrical connector by pushing it straight in until you hear or feel a click.
Before you reinstall the door panel, test the lock by pressing the power lock button on the door or using the key fob. The lock should move smoothly and lock or unlock without noise or resistance. If it does not work, disconnect the battery for 30 seconds and reconnect it to reset the door module, then test again. If it still does not work, check that the electrical connector is fully seated and that no linkage rods are bent or disconnected.
Reinstalling the door panel
Once the actuator is working, reinstall the door panel by reversing the removal process. Line up the panel with the door frame and press it firmly into place, starting at the top and working down. You should hear or feel the clips snap into place as the panel seats. Reinstall the bolts you removed earlier and tighten them with your 10mm socket.
Test the lock one more time from inside and outside the vehicle to make sure everything is working. Roll the window up and down to confirm the regulator still moves freely and the cable is not pinched. If the lock works and the window moves smoothly, you are done. If you replaced both rear door actuators, repeat the process on the other door.
When to take it to a shop instead
If you are not comfortable working inside the door panel, or if you do not have the tools, a Mercedes dealership or independent shop can do this job for you. Labor costs typically run $150 to $300 per door, depending on your location and the shop's rates. Some shops may charge a diagnostic fee if they need to confirm the actuator is the problem before you authorize the work.
You should also take it to a shop if the lock still does not work after you install the new actuator, because the problem may be in the door module or wiring rather than the actuator itself. A shop with diagnostic equipment can pinpoint the real issue and save you from replacing parts that are not broken.
Frequently Asked Questions
Can I replace just one rear door actuator, or do I need to do both?
You only need to replace the actuator on the door that is not working. However, if both rear doors have the same problem, both actuators have likely failed and should be replaced. Actuators typically last the life of the vehicle, so if one fails, the other is usually not far behind.
What if the lock still does not work after I install the new actuator?
Check that the electrical connector is fully seated and that no linkage rods are bent or disconnected. If everything looks correct, disconnect the battery for 30 seconds to reset the door module. If the lock still does not work, the problem may be in the wiring or the door control module, not the actuator. A shop with a diagnostic scanner can identify the real issue.
How long does a lock actuator usually last on a Sprinter?
Most actuators last the life of the vehicle if they are not exposed to moisture or used excessively. On a work vehicle like a Sprinter that is used daily, an actuator may fail after 100,000 to 150,000 miles. Moisture inside the door is the most common cause of early failure.
Do I need to reprogram anything after replacing the actuator?
No reprogramming is needed. The actuator is a straightforward electric motor with no computer coding. Once you install it and reconnect the electrical connector, it should work when ready. If it does not, a battery disconnect and reconnect will reset the door module.
Can I buy a used actuator instead of a new one?
Used actuators are available from salvage yards and online marketplaces, but there is no way to know how much life is left in them. Since a new actuator costs $80 to $150, the savings from buying used are small compared to the risk of the part failing again soon after installation.