The 246 is a part-time transfer case found in older GM trucks and SUVs

The 246 transfer case is a part-time four-wheel-drive system used by General Motors in trucks and sport utility vehicles built between the mid-1980s and early 2000s. It transfers engine power to the front and rear axles when you shift into four-wheel-drive mode, and returns power to the rear wheels only when you shift back to two-wheel-drive. The name "246" comes from its internal gear ratios and design designation within GM's lineup.

You'll find the 246 mounted directly behind the transmission on vehicles like the Chevrolet K5 Blazer, GMC Jimmy, Chevrolet Suburban, and Chevrolet pickup trucks from that era. It's a relatively straightforward mechanical system compared to full-time all-wheel-drive setups, which means repair and maintenance are often straightforward — but also that it has specific operating rules you need to follow to avoid damage.

Key Takeaways

  • The 246 is a part-time transfer case, meaning you should only engage four-wheel-drive when you actually need it, not for highway driving on dry pavement.
  • Fluid changes and seal replacements are the most common maintenance tasks, and the transfer case uses its own dedicated fluid separate from the transmission.
  • Grinding noises, difficulty shifting between two and four-wheel-drive, or fluid leaks are signs the transfer case needs inspection.
  • The 246 uses a chain-driven system inside, so regular fluid changes help prevent chain wear and extend the life of internal components.

How the 246 transfer case works

Inside the 246 housing is a chain that connects the input shaft (from the transmission) to the output shafts that send power forward and backward. When you shift into four-wheel-drive using the lever or buttons in your cab, a clutch engages and the chain transfers power to both the front and rear differentials at the same time. When you shift back to two-wheel-drive, the clutch disengages and power flows only to the rear axle.

The chain is the critical wear component. It runs in fluid, and that fluid carries away heat and debris. If the fluid level drops or becomes contaminated, the chain wears faster and can eventually break or slip, leaving you unable to shift into four-wheel-drive or causing the transfer case to jump out of gear while driving.

Fluid maintenance and what to check

The 246 has its own fluid reservoir separate from your transmission fluid. Check the level with the vehicle on level ground, engine off, and the transfer case cool. Most 246 units have a fill plug and a drain plug on the housing itself. The fluid should be bright red or amber; if it's dark brown or black, or if it smells burnt, the fluid has broken down and needs changing.

Fluid changes typically happen every 30,000 to 50,000 miles, though some owners go longer if the fluid stays clean. Drain the old fluid completely, replace the drain plug gasket, and refill with the correct fluid type — your owner's manual or a GM parts catalog will specify whether your 246 needs Dexron ATF, Mercon, or another specification. Overfilling is as bad as underfilling; use the fill plug hole as your reference point.

While you're underneath, look for leaks around the input seal (where the transfer case connects to the transmission), the output seals (front and rear), and the drain and fill plugs. Seals that weep a little are normal; steady drips mean a seal replacement is coming soon.

Common problems and what they sound like

A grinding or whining noise that gets louder when you're in four-wheel-drive usually means the chain is wearing or the fluid is low. Stop and check the fluid level before driving further; running a 246 dry will destroy the chain in minutes. If the level is fine but the noise continues, the chain or its sprockets are likely worn and the transfer case will need internal work.

Difficulty shifting into or out of four-wheel-drive — the lever or buttons feel stuck, or you hear a clunk but the four-wheel-drive doesn't actually engage — points to a worn clutch, a stuck shift fork, or low fluid. Try adding fluid first; if that doesn't help, the internal shift mechanism needs inspection. Some 246 units develop a problem where they slip out of four-wheel-drive while driving, which is usually a sign the clutch is worn or the chain has stretched enough that it can't hold tension.

Leaking fluid around the seals is common as the 246 ages. The input seal (at the transmission connection) and the front output seal (where the front driveshaft connects) fail most often. A slow weep won't hurt anything when ready, but a steady drip means you're losing fluid and should plan a seal replacement before the level drops too far.

When to shift into four-wheel-drive and when not to

The 246 is designed for part-time use only. Engage four-wheel-drive when you're on loose surfaces — snow, sand, gravel, or mud — where the front wheels need extra traction. Once you're back on dry pavement, shift out of four-wheel-drive when ready. Driving on dry pavement in four-wheel-drive forces the front and rear wheels to turn at slightly different speeds, which the transfer case can't accommodate smoothly. This causes binding, premature wear on the chain and clutch, and can damage the front differential.

In winter or in areas where you encounter snow regularly, it's common to shift into four-wheel-drive for the entire season and shift out in spring. That's acceptable if you're mostly on snow or wet roads. But if you're mixing highway driving and dry pavement with occasional snow, shift in and out as conditions change rather than leaving it in four-wheel-drive all the time.

Seal replacement and when it's necessary

The input seal and output seals are rubber components that wear over time. A slow leak — a few drops under the vehicle after it sits overnight — is annoying but not urgent. A steady drip that leaves a puddle within an hour means the seal is failing and you should plan a replacement within the next few weeks. If you ignore it and the fluid level drops below the minimum, you risk chain damage.

Seal replacement requires removing the transfer case from the vehicle, which is a job that takes several hours and requires lifting the truck safely. Many independent shops and dealerships can do this work. The seals themselves are inexpensive, but labor is the bulk of the cost. If you're already having the transfer case out for another reason — like a fluid leak inspection or chain work — replacing all three seals at once is usually the smart move.

Rebuilding versus replacing the transfer case

If the chain is worn, the clutch is slipping, or internal gears are damaged, you have two paths: rebuild or replace. A rebuild involves removing the transfer case, disassembling it, replacing worn parts (chain, sprockets, clutch, seals), and reassembling it. A replacement means installing a used or remanufactured transfer case from a salvage yard or parts supplier.

Rebuilds are usually cheaper if you have a trusted shop that specializes in transfer cases, but they take longer — often two to four weeks. Replacements are faster (a day or two) but cost more upfront. A remanufactured case often comes with a warranty, which a rebuilt case may not. Get quotes from both a local shop and a parts supplier before deciding; the price difference can be significant depending on your area and the condition of your vehicle.

Frequently Asked Questions

Can I drive on the highway in four-wheel-drive?

Not for long distances on dry pavement. The 246 is part-time only, meaning the front and rear wheels are forced to turn at the same speed, which causes binding and wear. Short stretches are okay, but shift back to two-wheel-drive as soon as you reach dry road. If you're in snow or on loose surfaces, four-wheel-drive is fine for highway speeds.

What does it mean if my transfer case won't shift into four-wheel-drive?

First, check the fluid level — low fluid is the most common cause. If the level is fine, the shift linkage may be stuck, the clutch may be worn, or internal components may be damaged. Have a mechanic inspect it; don't force the shifter, as that can break the linkage or internal parts.

How often should I change the transfer case fluid?

Every 30,000 to 50,000 miles is typical, though some owners go longer if the fluid stays clean. If you use four-wheel-drive frequently or tow regularly, change it more often. Check the fluid color and smell every oil change; if it's dark or burnt-smelling, change it sooner.

Is a slow leak from the transfer case serious?

A few drops over several days is annoying but not when ready dangerous. However, don't ignore it — the fluid level will eventually drop enough to damage the chain. Plan a seal replacement within the next few weeks, and check the fluid level monthly in the meantime.

What's the difference between a 246 and other GM transfer cases?

The 246 is part-time and chain-driven. Other GM transfer cases like the 208 (also part-time) and the full-time 203 work differently internally and have different maintenance needs. Check your owner's manual or the transfer case housing itself to confirm which one you have.