The 350 Small Block Chevy fires cylinders in the order 1-8-4-3-6-5-7-2

The firing order is the sequence in which the spark plugs ignite the fuel mixture in each cylinder. For a 350 small block Chevrolet engine, that sequence is 1-8-4-3-6-5-7-2. This order matters because it determines how you route the spark plug wires from the distributor cap to each cylinder, and getting it wrong will cause the engine to run rough, misfire, or not start at all.

The cylinders are numbered in a specific way on a 350: cylinders 1, 2, 3, and 4 are on the driver's side (left), and cylinders 5, 6, 7, and 8 are on the passenger's side (right). Cylinder 1 is at the front on the driver's side. The distributor cap has terminals arranged in a circle, and the rotor inside spins to point at each one in firing order as the engine turns.

If you are replacing spark plug wires, rebuilding the engine, or installing a new distributor, you need to know this firing order to route the wires correctly. A single wire in the wrong spot will prevent the engine from running.

Key Takeaways

  • The 350 small block Chevy fires cylinders in the order 1-8-4-3-6-5-7-2, and this sequence is the same whether your engine is a 1967 model or a 1990s version.
  • Cylinders 1, 2, 3, and 4 sit on the driver's side of the engine, with cylinder 1 at the front; cylinders 5, 6, 7, and 8 are on the passenger's side.
  • The distributor rotor spins and points to each terminal on the cap in firing order, so the spark plug wires must be routed to match that sequence.
  • Swapping even one spark plug wire to the wrong terminal will cause misfires or prevent the engine from starting.

How to locate cylinder 1 and number the rest

Before you can route spark plug wires correctly, you need to know which cylinder is which on your engine. Cylinder 1 is always at the front of the engine on the driver's side. Stand in front of the vehicle and look at the engine; the cylinder closest to you on the left side is number 1.

From there, the numbering goes backward along the driver's side: cylinder 1 is front, cylinder 3 is middle-front, and cylinder 4 is rear on that side. Cylinder 2 is in front of cylinder 4 but behind cylinder 3. On the passenger's side, the pattern mirrors: cylinder 5 is at the front, cylinder 7 is middle-front, and cylinder 8 is rear. Cylinder 6 sits between them.

A straightforward way to remember this: driver's side goes 1-3-4-2 from front to back, and passenger's side goes 5-7-8-6 from front to back. Once you know where each cylinder is, you can match it to the firing order 1-8-4-3-6-5-7-2 and route your spark plug wires accordingly.

Reading the distributor cap and rotor

The distributor cap is the plastic or ceramic piece on top of the distributor, with eight terminals around its edge (one for each cylinder). Inside, a rotor spins and points to each terminal as the engine runs. The rotor is connected to the engine's crankshaft through the distributor shaft, so it rotates in sync with the engine's motion.

One terminal on the cap is marked with a notch, line, or number 1. This is where the spark plug wire from cylinder 1 connects. The other terminals are arranged clockwise or counterclockwise around the cap from there. The rotor points to each terminal in firing order as it spins, so the spark plug wires must be routed to follow that same sequence.

To route the wires correctly, start by connecting the cylinder 1 spark plug wire to the terminal marked 1 on the cap. Then, moving around the cap in the direction the rotor spins (usually clockwise), connect the remaining wires in firing order: 8, 4, 3, 6, 5, 7, 2. If you install them in any other order, the engine will not fire correctly.

What happens when spark plug wires are in the wrong order

If one or more spark plug wires are routed to the wrong terminals, the engine will misfire. A misfire means the spark plug fires at the wrong time in the cylinder's cycle, so the fuel does not ignite when it should. The result is a rough idle, hesitation during acceleration, loss of power, or a check engine light on the dashboard.

In some cases, if multiple wires are wrong, the engine will not start at all. The ignition system will try to fire the cylinders, but the timing will be so far off that combustion cannot happen. You may hear the engine crank but not turn over, or it may start briefly and stall.

The fix is straightforward: remove the spark plug wires one at a time and route them to the correct terminals on the distributor cap according to the firing order. Double-check each wire before starting the engine.

Checking and replacing spark plug wires

Spark plug wires degrade over time and can crack, fray, or lose their connection to the spark plug or distributor cap. If you are replacing them, you need to remove and install them one at a time so you do not mix up the routing. Never remove all eight wires at once unless you have written down or photographed which wire goes where.

To replace a wire, grip the boot (the rubber connector) at the spark plug end, twist gently, and pull straight out. Do the same at the distributor cap end. Slide the new wire onto the spark plug first, then route it to the correct terminal on the distributor cap and push it on firmly. You should hear or feel a click when the boot seats properly.

If you are unsure which terminal is which on the cap, refer to the cap itself—most have the cylinder numbers molded or printed on the terminals, or a notch or line marking cylinder 1. If your cap does not have markings, consult the engine's service manual or a repair guide specific to your year and model.

Distributor installation and timing

If you are installing a new or rebuilt distributor, you must set its initial position before you can route the spark plug wires. The distributor shaft has a slot or key that fits into a corresponding slot in the engine block, so the distributor can only be installed one way. However, the rotor can be pointing in any direction when you insert the distributor, which affects where the spark fires.

To install the distributor correctly, turn the engine by hand (using a wrench on the crankshaft bolt) until the rotor points toward the terminal marked 1 on the cap. Then insert the distributor so the rotor continues to point at terminal 1. This ensures that when the engine starts, the first spark fires in cylinder 1 at the right moment in its cycle.

After installation, route the spark plug wires in firing order around the cap. The engine should start and run. You may need to adjust the ignition timing using a timing light, depending on your engine's age and condition, but the firing order itself does not change.

Frequently Asked Questions

Is the firing order the same for all 350 small block Chevy engines?

Yes. The firing order 1-8-4-3-6-5-7-2 is the same for every 350 small block Chevy, regardless of the year it was built. The cylinder numbering and distributor layout are identical across all 350 engines.

What if I cannot find a marking for cylinder 1 on my distributor cap?

Look for a notch, line, or raised bump on the cap's edge that aligns with a corresponding mark on the distributor body. If the cap has no markings, remove it and look inside at the rotor. The rotor's contact point should align with a terminal when the engine is at top dead center on cylinder 1. A service manual for your specific year will show you exactly which terminal that is.

Can I route the spark plug wires in reverse firing order?

No. The firing order is determined by the engine's design and cannot be changed. Reversing the order will cause severe misfires and the engine will not run properly. The only correct sequence is 1-8-4-3-6-5-7-2.

Do I need to disconnect the battery before working on spark plug wires?

It is a good practice to disconnect the negative battery terminal before removing or installing spark plug wires. This prevents accidental shorts and protects both you and the engine's electrical system. Reconnect the battery after you finish and before starting the engine.

What should I do if the engine still misfires after I have routed the wires correctly?

Check that each wire is fully seated on both the spark plug and the distributor cap terminal. A loose connection will cause a misfire even if the wire is in the correct location. If all connections are tight, the spark plugs themselves may be worn or fouled, or the distributor cap and rotor may be damaged. Inspect them and replace as needed.