A rebuild kit gives you the internal seals and gaskets, but not the machine work or labor
A 350 small block rebuild kit contains the gaskets, seals, and soft parts that wear out over time inside your engine. It does not include new pistons, rings, bearings, or cylinder boring — those are separate purchases or machine shop services. The kit sits somewhere between a basic gasket set (which covers only external seals) and a full engine overhaul, where a machine shop tears down, measures, and rebuilds the entire block.
What you get depends on which kit you buy. A basic kit might include valve cover gaskets, oil pan gasket, timing cover gasket, and intake manifold gasket. A mid-range kit adds water pump gasket, fuel pump gasket, and freeze plugs. A comprehensive kit includes all of those plus internal seals like the rear main seal and front crankshaft seal. None of them include the labor to install the parts or the machine work to measure and hone the cylinders.
The 350 is a Chevrolet small block engine used in trucks, cars, and marine applications from the 1960s onward. Because it's been in production for decades and remains common in used vehicles, rebuild kits are widely available and relatively inexpensive compared to kits for other engines.
Key Takeaways
- A rebuild kit contains gaskets and seals but not pistons, rings, bearings, or machine work — you must budget separately for those items and labor.
- Basic kits cover external gaskets only; mid-range kits add water pump and fuel pump seals; comprehensive kits include internal seals like the rear main seal.
- You will need a machine shop to measure your cylinders, bore them if needed, and hone them to the correct size for new rings and pistons.
- Total rebuild cost typically runs $1,500 to $3,500 in parts and labor, depending on whether the block needs boring and what condition the crankshaft and camshaft are in.
What's actually in the box
Rebuild kits come in three rough tiers. The basic gasket set includes valve cover gasket, oil pan gasket, timing cover gasket, and intake manifold gasket — the seals you see when you open the hood. These are the parts that dry out and crack from heat cycling, causing oil leaks around the outside of the engine.
A mid-range rebuild kit adds the water pump gasket, fuel pump gasket, and freeze plugs (the small metal plugs in the block that prevent coolant from freezing and cracking the casting). Some kits in this tier also include the thermostat housing gasket and oil filter adapter gasket.
A comprehensive or full rebuild kit includes everything above plus the rear main seal (the seal where the crankshaft exits the back of the block), the front crankshaft seal, and sometimes the oil pump gasket. This is the kit you want if you are pulling the engine apart far enough to access those internal seals, because you will have the block open anyway and replacing them costs almost nothing in labor at that point.
No kit includes new pistons, piston rings, bearings, gasket maker, sealant, or the machine work to bore and hone the cylinders. You buy those separately based on what your machine shop finds when they measure the block.
Machine shop work you cannot skip
Before you install new rings and pistons, the cylinders must be measured and honed to the correct size. A machine shop uses a bore gauge to measure each cylinder's diameter and taper (how much it has worn). If the wear is within limits, they hone the cylinders to a smooth finish so new rings will seal properly. If the wear is too much, they bore the cylinders oversize and you buy oversize pistons to match.
The machine shop will also measure the crankshaft for wear and the camshaft for lobe wear. If the crankshaft is worn, it can sometimes be ground undersize and you buy undersize bearings. If the camshaft lobes are worn, the camshaft must be replaced. These measurements determine whether your rebuild is a straightforward hone-and-ring job or a more expensive overhaul.
A basic hone and ring job (no boring, crankshaft and camshaft in acceptable condition) typically costs $400 to $800 in machine shop labor. If boring is needed, add $300 to $600 depending on how much material must be removed. If the crankshaft must be ground or the camshaft replaced, add another $300 to $500.
Comparing rebuild kits by price and what they cover
| Kit Type | Typical Price Range | What's Included | When to Use It |
|---|---|---|---|
| Basic gasket set | $40–$80 | Valve cover, oil pan, timing cover, intake manifold gaskets | Fixing external oil leaks without pulling the engine apart |
| Mid-range rebuild kit | $120–$250 | Basic gaskets plus water pump, fuel pump, freeze plugs | Pulling the engine for a refresh but not a full teardown |
| Comprehensive rebuild kit | $200–$400 | All above plus rear main seal, front crankshaft seal, oil pump gasket | Full engine teardown with new pistons and rings |
What you still have to buy separately
The rebuild kit covers seals and gaskets. You must buy pistons and rings as a set, usually in standard or oversize depending on what the machine shop finds. A set of pistons and rings for a 350 typically costs $200 to $400. You also need a set of main bearings and rod bearings, which run $100 to $250 depending on whether you go with OEM Chevrolet parts or aftermarket.
You will need gasket maker or RTV sealant (a silicone compound that fills small gaps between parts), which costs $10 to $20. If the oil pump is worn, you may need a new one ($80 to $150). If you are replacing the timing chain and gears, add another $100 to $200. A new water pump is often replaced during a rebuild and costs $50 to $120.
Labor to remove the engine, disassemble it, send parts to the machine shop, reassemble it, and reinstall it typically runs $1,000 to $2,000 depending on your location and the shop's hourly rate. Some shops charge a flat rate for a 350 rebuild; others charge hourly. Ask for a written estimate before you start.
Choosing between a kit and buying parts individually
A rebuild kit bundles the most common gaskets and seals at a lower price than buying them one at a time. If you know exactly which seals are leaking, buying only those parts is cheaper. But if you are pulling the engine apart, buying a comprehensive kit ensures you have everything you need and do not have to make a second trip to the parts store halfway through reassembly.
Some shops include a gasket kit with their rebuild labor, so ask before you buy separately. Others expect you to supply the kit. If you are doing the work yourself, a kit saves time because everything arrives together and you do not have to cross-reference part numbers for each individual seal.
Aftermarket kits (from companies like Sealed Power or Felpro) are usually cheaper than OEM Chevrolet kits and perform the same function. The difference is in how long the seals last before they dry out again — OEM seals sometimes last slightly longer, but the difference is usually only a few years. For a rebuild, either is acceptable.
Signs you need a rebuild versus just new gaskets
If you have oil leaking from the valve covers or oil pan and the engine runs normally, you need a basic gasket set, not a rebuild kit. If the engine is burning oil (blue smoke from the exhaust), losing coolant into the oil, or has low compression, you need a rebuild with new rings and pistons.
A compression test tells you whether the rings are sealing. If all cylinders read within 10 percent of each other and above 120 psi, the rings are probably fine and you do not need a full rebuild. If one or more cylinders read low and do not improve when you squirt oil into the cylinder, the rings are worn and a rebuild is necessary.
If the engine has never been rebuilt and has over 100,000 miles, a rebuild is often worth doing if the block is in good condition. If the block has cracks, is severely corroded, or has been rebuilt multiple times, replacement may be more cost-effective than another rebuild.
Frequently Asked Questions
Do I need a comprehensive kit or will a basic kit work?
It depends on how far you are taking the engine apart. If you are only replacing external gaskets, a basic kit is enough. If you are pulling the engine and removing the oil pan, timing cover, and intake manifold, a mid-range kit saves money. If you are replacing pistons and rings, buy a comprehensive kit so you have the rear main seal and front crankshaft seal on hand.
Can I use a 350 rebuild kit on a different Chevy engine?
No. A 350 kit is specific to the 350 block. Other small blocks like the 305, 327, or 400 have different gasket sizes and seal locations. Using the wrong kit will result in leaks. Check your engine's displacement before ordering.
How long does a rebuild typically take?
Removal and reinstallation usually takes one to two weeks at a shop, depending on their schedule. Machine shop work (boring, honing, grinding) adds another week. If parts must be ordered or special work is needed, total time can stretch to three to four weeks. Ask the shop for a timeline before you drop off the engine.
What's the difference between a hone and a bore?
A hone smooths the cylinder walls without removing much material — used when cylinders are within acceptable wear limits. A bore removes material to enlarge the cylinder, used when wear is too severe for a hone alone. Boring requires oversize pistons; honing uses standard-size pistons.
Should I replace the timing chain while the engine is apart?
If the timing chain has over 100,000 miles or shows visible slack, replace it. The labor is already paid for since the timing cover is off. A new timing chain, gears, and tensioner costs $150 to $250 and prevents a costly failure later. If the chain looks tight and the engine has fewer than 80,000 miles, you can defer it.