A 4-40 clearance hole lets a bolt pass through without threading
A 4-40 clearance hole is a hole drilled to allow a 4-40 bolt to slide through freely without catching or binding. The "4-40" refers to a screw size: number 4 diameter, 40 threads per inch. A clearance hole for this bolt is 0.146 inches (about 3.7 millimeters) in diameter — slightly larger than the bolt shaft itself so the bolt can move through without resistance.
In vehicle repair and assembly, clearance holes appear wherever a bolt needs to pass through one part and thread into another. The bolt slides through the clearance hole in the first part, then the threaded portion grips the second part. This is different from a tapped hole, which is threaded all the way through and accepts the bolt directly.
You encounter 4-40 fasteners in automotive work on trim pieces, brackets, electrical connectors, and light assemblies — anywhere a small, precise fastener is needed. Understanding the difference between clearance and tapped holes prevents cross-threading, stripped fasteners, and parts that won't sit flush.
Key Takeaways
- A 4-40 clearance hole is 0.146 inches in diameter and allows the bolt to pass through without threading into that part.
- Clearance holes are used when a bolt must pass through one component and thread into a second component behind it.
- Using the wrong hole size or confusing a clearance hole with a tapped hole causes cross-threading and stripped fasteners.
- Automotive trim, brackets, and light fixtures commonly use 4-40 fasteners in clearance-hole configurations.
How clearance holes differ from tapped holes
A tapped hole has threads cut into it and accepts a bolt directly — the bolt threads into the hole itself. A clearance hole has no threads; the bolt slides through it and threads into a tapped hole in a part behind it. This two-part arrangement is necessary when you need to fasten two components together but only one of them can accommodate threads.
In a vehicle door panel, for example, a trim ring might have a clearance hole so a bolt can pass through it and thread into the metal frame behind. The trim ring sits flush against the frame because the bolt does not catch on the ring itself — it passes straight through. If you tried to thread the bolt into the trim ring instead, the ring would sit proud (raised) and the fastener would be visible and loose.
Confusing the two causes real problems. Threading a bolt into a clearance hole will strip the hole because there are no threads to grip. Trying to pass a bolt through a tapped hole often results in cross-threading — the bolt catches at an angle and damages both the bolt and the hole threads.
Why 4-40 is common in automotive applications
The 4-40 size strikes a balance between strength and precision. It is large enough to hold trim and brackets securely but small enough to fit into tight spaces where larger fasteners will not. Vehicle manufacturers use 4-40 bolts extensively in interior trim, exterior trim rings, light housings, and connector brackets because the size is standardized, inexpensive, and reliable.
When you remove a trim piece or light assembly and see a small bolt, it is often 4-40. The fastener is small enough that you can work with it by hand or with a standard screwdriver or wrench, but it provides genuine holding power. Stainless steel 4-40 bolts resist corrosion in underhood and exterior applications, which is why they appear in headlight bezels, grille trim, and weatherstripping brackets.
Drilling a 4-40 clearance hole correctly
If you are drilling a new clearance hole for a 4-40 bolt, use a number 43 drill bit, which produces a hole of 0.089 inches — the correct size for a clearance hole. Some technicians use a number 42 bit (0.094 inches) as well; both fall within acceptable tolerance. The hole should be clean and free of burrs so the bolt slides smoothly without binding.
When drilling through metal, use a cutting fluid or light machine oil to reduce friction and heat. Drill slowly and let the bit do the work rather than forcing it. If you are drilling through multiple layers — such as a trim ring and the frame behind it — drill through both at once to may support the holes align perfectly.
After drilling, remove any burrs with a deburring tool or the back of a larger drill bit. A burr will catch the bolt and make installation difficult. Wipe away metal shavings before installing the bolt so they do not interfere with the fit.
Installing a bolt through a clearance hole
Slide the bolt through the clearance hole first. It should move freely without any resistance or binding. If the bolt catches or requires force to pass through, the hole is too small or has burrs. Stop and investigate rather than forcing the bolt, which can damage the fastener or enlarge the hole unevenly.
Once the bolt passes through the clearance hole, align it with the tapped hole in the part behind and begin threading by hand. Hand-threading prevents cross-threading — you will feel when ready if the bolt is catching at an angle. Once the bolt is hand-threaded a few turns, you can use a wrench or socket to tighten it fully.
Tighten firmly but do not over-tighten small fasteners like 4-40 bolts. Over-tightening strips the threads in the tapped hole and can crack brittle trim pieces. A snug fit that does not move is sufficient; the bolt should not spin freely, but you should not need a wrench to remove it later.
Common problems and how to avoid them
The most frequent mistake is drilling a clearance hole too small. A hole that is too tight will bind the bolt and make installation difficult. If you must drill a hole for a 4-40 bolt and do not have a number 43 bit, a number 42 bit is acceptable. Avoid anything smaller, as the bolt will not pass through smoothly.
Cross-threading occurs when a bolt enters a tapped hole at an angle. This happens when the clearance hole and tapped hole are not aligned or when the bolt is forced in at an angle. Always hand-thread first to confirm the bolt is going in straight. If you feel resistance or grinding, back the bolt out and realign.
Stripped tapped holes cannot be repaired easily. If a bolt spins in a tapped hole without gripping, the threads are damaged. You can sometimes rescue the hole by using a slightly larger bolt size (such as 6-32 instead of 4-40), but this requires drilling a new hole. Prevention — careful hand-threading and moderate tightening — is far simpler than repair.
When to use stainless steel versus standard bolts
Stainless steel 4-40 bolts resist rust and corrosion, making them the right choice for exterior trim, underhood brackets, and any fastener exposed to moisture or salt. Standard steel bolts are cheaper and adequate for interior trim in dry environments, but they will rust if exposed to weather or road salt over time.
If you are replacing a corroded bolt, use stainless steel even if the original was standard steel. The small extra cost prevents the same problem from recurring. Stainless bolts are widely available in automotive and hardware suppliers and come in the same sizes as standard steel, so substitution is straightforward.
Frequently Asked Questions
What size drill bit do I use for a 4-40 clearance hole?
Use a number 43 drill bit, which produces a hole of 0.089 inches. A number 42 bit (0.094 inches) is also acceptable. Both allow the bolt to pass through freely without binding.
Can I use a 4-40 bolt in a clearance hole that is slightly too large?
A hole that is slightly oversized will not harm the bolt, but the bolt may move or rattle in the hole. If the hole is much larger than needed, the bolt will not sit flush and the fastened part may shift. Drill to the correct size when possible.
What happens if I thread a 4-40 bolt into a clearance hole?
Threading into a clearance hole will strip it because there are no threads to grip. The bolt will spin freely and will not hold. The hole is then damaged and difficult to repair without drilling a larger hole and using a bigger bolt.
How tight should a 4-40 bolt be?
Tighten until snug and the part does not move, but do not over-tighten. Small fasteners strip easily under excessive force. If you can remove the bolt by hand with moderate effort, it is tight enough.
Why does my 4-40 bolt keep cross-threading?
Cross-threading usually means the clearance hole and tapped hole are not aligned, or the bolt is being forced in at an angle. Always hand-thread first to confirm alignment. If you feel grinding or resistance, back out and realign before continuing.