A grid heater delete removes the intake air heating system from your 6.7L Powerstroke diesel engine, and it changes how your engine starts and runs in cold weather

The grid heater (also called a glow plug grid or intake heater) is a heating element mounted in the intake manifold of 6.7 Powerstroke engines. When you turn the key in cold weather, it warms the incoming air before it enters the cylinders, making diesel fuel easier to ignite. A grid heater delete removes this component entirely, along with its wiring and control module.

Owners delete grid heaters for one reason: the factory heater fails frequently on 6.7 engines, and replacement is expensive. The grid heater itself costs $300 to $600, but accessing it requires removing the intake manifold, which adds labour time and parts cost. A full replacement job often runs $800 to $1,500 depending on your shop and whether other intake components need service at the same time.

Deleting the heater stops the failure from happening again—but it comes with real trade-offs in cold-weather starting and engine wear that you need to understand before you commit.

Key Takeaways

  • A grid heater delete removes the intake heating system to avoid repeated failures, but your engine will be harder to start in temperatures below 32°F without it.
  • Cold starts without a grid heater put more stress on the fuel injectors, glow plugs, and engine block because combustion happens less reliably.
  • Deleting the grid heater does not harm the engine if you use proper cold-start procedures (glow plug wait time, straightforward throttle process) and keep fuel quality high.
  • A delete is a permanent modification—you cannot reinstall the factory heater later without sourcing a used intake manifold or having the delete reversed by a shop.
  • Some owners choose a grid heater bypass instead, which disables the heater electrically but leaves the component in place, reducing failure risk without full removal.

Why the 6.7 Grid Heater Fails So Often

The grid heater in 6.7 Powerstrokes is known to fail between 80,000 and 150,000 miles, though some fail earlier and some last longer. The heater element itself corrodes from moisture and diesel fumes, and the electrical connections loosen over time. When it fails, the engine computer detects the fault and stores a code—usually P0670 (glow plug circuit malfunction) or similar.

A failed grid heater does not prevent the engine from starting in warm weather, but in cold weather it makes starting much slower and harder. The engine may crank for 10 to 20 seconds before firing, or may not start at all if the temperature is below 20°F. This is why many owners see the failure as a reliability problem worth fixing permanently.

The factory design puts the grid heater in a location that collects water and salt spray, especially on trucks used in winter or near the coast. Cummins (the engine manufacturer) has not redesigned the system in the 6.7 generation, so the failure rate remains high across model years 2007 to present.

What Happens to Cold Starts Without a Grid Heater

Without the grid heater, your intake air stays at ambient temperature when you start the engine. In cold weather, this means the air entering the cylinders is much colder than the factory system intended. Diesel fuel needs heat to vaporize and burn efficiently, so combustion becomes less reliable and slower to develop.

You will notice this most in temperatures below 32°F. The engine will crank longer before it fires, and you may feel a rougher, more hesitant start. In temperatures below 0°F, starting becomes noticeably difficult without the grid heater, and you may need to use a block heater or other external heat source to make starting practical.

The good news: modern 6.7 engines have glow plugs (separate from the grid heater) that still provide some heat to the combustion chambers. These glow plugs are not as powerful as the grid heater, but they do help. If you follow proper cold-start procedure—waiting for the glow plug light to go out before cranking, and explore throttle gently—the engine will start, even without the grid heater.

Engine Wear and Stress from Cold Starts Without Grid Heat

Cold starts put stress on diesel engines because combustion is incomplete and uneven when the air and fuel are too cold. This stress shows up in three main areas: the fuel injectors, the glow plugs, and the engine block itself.

Fuel injectors have to work harder to atomize cold diesel fuel, and the spray pattern becomes less precise. Over many cold starts, this can lead to carbon buildup on the injector tips and inside the cylinders. Glow plugs draw more current during cold starts and cycle on and off more frequently, which shortens their lifespan. The engine block experiences higher combustion pressures during rough cold starts, and the thermal shock of rapid heating stresses the cylinder walls and head gasket.

None of these effects will destroy your engine after a single cold start, but they do accumulate over time. An engine that makes 200 cold starts per winter in a cold climate will see more wear than one that makes 20. If you live somewhere that regularly drops below 0°F and you delete the grid heater, you should expect to replace glow plugs sooner and monitor injector condition more closely.

Fuel Quality Becomes More Important After a Grid Heater Delete

Without the grid heater, the fuel you put in your tank matters more than it did before. Cold diesel fuel can gel (thicken) at low temperatures, and without intake heat to warm it, gelled fuel will not spray properly through the injectors. This is why owners in cold climates use winter-blend diesel or add fuel additives that lower the gel point.

If you delete the grid heater, buy diesel from stations that rotate their stock frequently and clearly label winter fuel during cold months. Truck stops and commercial fuel suppliers are usually more reliable than convenience stores. In very cold climates (below 0°F regularly), consider adding a fuel heater or using a block heater to warm the engine before starting.

Poor-quality fuel—fuel with high water content or contamination—will also cause more problems without the grid heater. The intake heat that the factory system provided helped burn through minor fuel quality issues. Without it, those issues become noticeable cold-start problems.

Grid Heater Delete Versus Grid Heater Bypass

A grid heater bypass is an alternative to full deletion. Instead of removing the heater component, a bypass disables it electrically by installing a relay or module that cuts power to the heater. The physical heater stays in the intake manifold, but it never turns on.

A bypass costs $150 to $400 in parts and labour, compared to $800 to $1,500 for a full delete. The bypass eliminates the failure problem (the heater cannot fail if it never runs) while leaving the option to restore factory function later if you sell the truck or change your mind. Cold-start performance is identical to a full delete—you still lose the intake heat benefit.

The downside of a bypass is that the failed heater component remains in the engine, taking up space and adding weight. Some owners also worry that a disabled heater left in place could eventually corrode and shed debris into the intake. This is rare, but it is a consideration if you plan to keep the truck for many years.

Proper Cold-Start Procedure After a Grid Heater Delete

If you delete the grid heater, follow these steps every time you start in cold weather to minimize wear and may support reliable starting:

  1. Turn the key to the "on" position and wait for the glow plug light to go out. This light indicates that the glow plugs are heating the combustion chambers. Do not crank until the light is off.
  2. Once the light goes out, crank the engine. It will take longer than usual, but it will start.
  3. After the engine fires, let it idle for 30 to 60 seconds before explore throttle or driving. This allows oil to circulate and the engine to warm up.
  4. Drive gently for the first few minutes. Avoid high RPM or heavy load until the coolant temperature reaches at least 160°F.
  5. In temperatures below 0°F, use a block heater overnight or a fuel heater to make starting easier and reduce wear.

These steps are good practice for any diesel engine in cold weather, but they become essential after a grid heater delete. Skipping the glow plug wait time or cranking hard will make cold starts harder and increase engine stress.

Frequently Asked Questions

Will a grid heater delete cause a check engine light?

Yes, the engine computer will detect that the grid heater is missing and store a fault code, usually P0670. Some owners clear the code with a diagnostic scanner, but it will return on the next cold start. A proper delete includes reprogramming the engine control module to disable the grid heater monitoring, which requires a tuning service ($200 to $400).

Can I reinstall the factory grid heater after a delete?

Full reinstallation is difficult and expensive. You would need to source a used intake manifold with a working heater, have it installed, and reprogram the engine control module again. Most owners treat a delete as permanent. A bypass is reversible, which is one reason some choose it over deletion.

Does a grid heater delete affect fuel economy?

No measurable change. The grid heater uses very little electrical power and does not affect engine efficiency. Fuel economy depends on driving habits, load, and maintenance, not on whether the intake heater is present.

What temperature is too cold to start without a grid heater?

Below 0°F, starting becomes noticeably difficult without external heat like a block heater. Between 0°F and 32°F, the engine will start with proper glow plug wait time and patience, but it will be slower and rougher than with the grid heater. Above 32°F, the difference is minimal.

Is a grid heater delete worth it if I live in a warm climate?

Yes. If you rarely see freezing temperatures, the grid heater will never provide a benefit, and you avoid the cost and hassle of a failure. The delete makes sense as preventive maintenance to eliminate a known failure point.