Start with a full mechanical inspection before turning the key
A 1968 Camaro Z/28 that has been sitting in a barn for years or decades needs a thorough inspection before you attempt to start it. The fuel system, cooling system, brake lines, and electrical connections have all degraded in storage. Rubber seals crack, metal corrodes, and fuel turns to varnish. Driving it without checking these systems first can damage the engine, fail the brakes, or cause a fire.
Have a mechanic experienced with classic cars perform a pre-start inspection. This means checking the oil level and condition, inspecting all hoses and belts for cracks or brittleness, examining brake fluid and brake lines for leaks or corrosion, testing the battery, and looking at the fuel tank interior for rust and debris. The mechanic should also inspect the cooling system, transmission fluid, and all visible wiring for damage.
Do not assume the car will start. Do not assume the brakes work. Do not assume the fuel pump will function. Each of these systems needs verification before the engine runs.
Key Takeaways
- Have a mechanic inspect the fuel system, brakes, cooling system, and electrical components before attempting to start the engine, because all of these degrade during storage.
- The fuel tank likely contains rust and varnish that will clog the fuel filter and injectors, so plan to drop and clean the tank or replace it entirely.
- Brake fluid absorbs moisture over time and loses stopping power, so the entire brake system should be flushed and refilled before driving on public roads.
- A 1968 Z/28 with original matching numbers (engine, transmission, and VIN) is worth significantly more than one with replacements, so document what you find before any work begins.
- Restoration costs for a barn find typically exceed the purchase price by a factor of two to four, depending on how much rust is present and whether you keep original parts.
Drain and flush the fuel system completely
Fuel that has sat for years turns into a thick, sticky varnish that clogs fuel filters, carburetors, and injectors. A 1968 Z/28 uses a carburetor, not fuel injection, but the principle is the same: old fuel will not flow, and it will leave deposits that are difficult to remove.
The safest approach is to drop the fuel tank, have it professionally cleaned or replaced, and install a new fuel filter before refilling. If the tank shows heavy rust on the interior, replacement is usually cheaper than restoration. A new fuel tank for a 1968 Camaro costs between $300 and $600 depending on the supplier. A professional tank cleaning runs $200 to $400. Either way, you avoid the risk of varnish particles reaching the carburetor once the engine is running.
Do not straightforward add fuel system cleaner to old fuel and hope it works. The varnish is already coating the tank walls and will continue to shed particles into the fuel line.
Replace the brake fluid and inspect all brake lines
Brake fluid is hygroscopic, meaning it absorbs moisture from the air over time. After years in storage, the fluid loses its ability to transfer pressure and may have corroded the brake lines from the inside. A barn find Camaro with original brake lines may have pinhole leaks you cannot see until pressure is applied.
Flush the entire brake system: master cylinder, wheel cylinders, brake lines, and calipers or drum brakes. Use fresh DOT 3 or DOT 4 fluid appropriate for the year. Inspect every inch of brake line for corrosion, cracks, or seeping. If any line shows rust or damage, replace it. Brake failure at speed is life-threatening, so this is not an area to cut corners.
Bleed the brakes after flushing to remove air from the lines. Test the brakes in a parking lot or empty lot before driving on public roads. The pedal should feel firm and responsive, not soft or spongy.
Check the cooling system and replace old coolant
The cooling system in a 1968 Camaro consists of the radiator, water pump, hoses, thermostat, and heater core. All of these corrode or degrade during storage. The coolant itself breaks down and becomes acidic, which accelerates corrosion inside the engine block.
Drain the old coolant completely and flush the system with distilled water until the water runs clear. Replace the thermostat, water pump gasket, and all hoses. Refill with fresh coolant mixed to the correct ratio. A 1968 Camaro typically uses a 50/50 mix of coolant and distilled water.
If the radiator shows leaks or heavy corrosion, have it professionally rodded and sealed or replaced. A leaking radiator will overheat the engine and cause damage within minutes of driving.
Document the original parts and matching numbers before restoration
A 1968 Camaro Z/28 with original matching numbers — meaning the engine block, transmission, and VIN all correspond to the factory build sheet — is worth substantially more than one with replacements. Before you replace anything, photograph and document what you find.
The engine block casting number is stamped on the passenger side of the block near the cylinder head. The transmission pan has a code stamped into it. The VIN is on the dashboard and on the driver's door jamb. Cross-reference these numbers with the original build documentation if you have it, or consult a Camaro-specific resource like the National Camaro Club or a Z/28 registry.
If the original engine or transmission is damaged beyond repair, you may choose to source a correct replacement from a salvage yard or specialty supplier rather than install a non-original part. This decision affects the car's value and authenticity. Document your choices in writing and keep receipts for any parts you source.
Plan for rust repair and body work
A barn find will have rust somewhere: under the hood, in the floor pans, along the rocker panels, or in the trunk. Surface rust can be wire-brushed and treated with rust converter. Structural rust — rust that has eaten through the metal — requires cutting out the damaged section and welding in new metal.
Have a body shop or restoration specialist inspect the car and provide a written estimate for rust repair. Floor pans, rocker panels, and door bottoms are common rust spots on a 1968 Camaro. If rust has reached the frame rails or suspension mounting points, the repair cost rises significantly. Some barn finds have rust so extensive that restoration is not economically feasible.
Budget for this work before you commit to the project. A partial restoration addressing only mechanical systems and surface rust may cost $5,000 to $15,000. A full restoration including structural rust repair, paint, interior, and engine rebuild can exceed $30,000 to $50,000 or more, depending on the extent of damage and your choice of original versus modern parts.
Decide between a full restoration and a driver-quality rebuild
You have two paths: restore the car to original condition for show and collection, or rebuild it to run and drive reliably without worrying about originality. The choice affects cost, timeline, and the final value of the car.
A full restoration means sourcing correct original parts, matching paint codes, restoring the interior to factory specifications, and ensuring every detail matches the build sheet. This approach takes years and costs the most. A driver-quality rebuild means replacing worn parts with modern equivalents where necessary, repainting to a solid color, and focusing on mechanical reliability and safety. A driver-quality car is finished faster and costs less, but it will not command the same price at auction or sale.
Many owners split the difference: they restore the engine and mechanical systems to original specifications, replace the interior with correct reproduction parts, and repaint in the original color. This approach balances authenticity with practicality and cost.
Frequently Asked Questions
How do I know if a 1968 Camaro Z/28 is a real Z/28 or a clone?
A real Z/28 has a 302-cubic-inch engine with a Chevrolet casting number on the block, a Muncie M22 "rock crusher" transmission, and a 12-bolt rear axle with 3.73 gearing. The VIN will have a Z in the model code position. A clone has a different engine, transmission, or rear axle. Check the casting numbers and VIN against the National Camaro Club database or a Z/28 registry before investing in restoration.
Can I drive a barn find to a mechanic or restoration shop, or do I need a trailer?
Trailer it. The brakes, steering, and suspension have not been tested, and the tires may be flat or unsafe. Driving an untested car on public roads risks your safety and the safety of others. Rent a car trailer or flatbed for transport until the car has passed a full mechanical inspection and test drive in a controlled environment.
What is the most common failure point when starting a barn find after years of storage?
The fuel system and ignition system are the most common culprits. Old fuel clogs the carburetor, and old spark plugs or corroded ignition wires prevent the engine from firing. Replace the spark plugs, ignition wires, and fuel filter before attempting to start. If the engine still will not start, have the carburetor professionally cleaned or rebuilt.
Should I restore a barn find Camaro myself or hire a professional shop?
If you have mechanical experience and access to tools, you can handle the mechanical work: brakes, cooling system, fuel system, and basic engine service. Body work, welding, and paint require specialized equipment and skill. Most owners handle the mechanical work themselves and hire a body shop for rust repair and painting, which saves money while maintaining quality on the most visible work.
What is a barn find 1968 Camaro Z/28 worth after restoration?
A fully restored original Z/28 with matching numbers typically sells for $40,000 to $80,000 depending on condition, mileage, and documentation. A driver-quality rebuild is worth $25,000 to $45,000. A clone or non-original car is worth less. The value depends on how much original equipment you retain and how well the restoration is executed. Consult recent auction results and classified listings for cars in similar condition to set realistic expectations.