What you need to know before replacing Bobcat MT100 tracks

Bobcat MT100 tracks wear out from regular use and need replacement when you see visible damage, reduced traction, or chunks missing from the rubber. A full track replacement on the MT100 typically costs between $800 and $1,500 per track when you buy OEM (original equipment manufacturer) parts, though aftermarket options run $400 to $900 per track. The job takes 4 to 8 hours if you have the right tools and a lift, or you can pay a dealer $1,500 to $3,000 in labor to do both tracks.

You'll need to remove the old track, inspect the undercarriage for damage, and install the new one. The process is straightforward but physically demanding — tracks are heavy, and you need the machine lifted safely. Most owners either do this themselves with a floor jack and jack stands, or take the MT100 to a Bobcat dealer or independent equipment repair shop.

Key Takeaways

  • Bobcat MT100 replacement tracks cost $400 to $1,500 each depending on whether you buy OEM or aftermarket parts.
  • You can replace tracks yourself with a floor jack, jack stands, and basic hand tools, or pay a shop $1,500 to $3,000 in labor for both tracks.
  • The replacement process involves lifting the machine, removing bolts, sliding out the old track, and installing the new one — a job that takes 4 to 8 hours per side.
  • Inspect the drive sprocket, idler wheel, and rollers while the track is off, because damage to these parts will wear out a new track quickly.
  • Aftermarket tracks from brands like Camso and Prowler are cheaper than OEM but may have a shorter lifespan depending on your use.

OEM versus aftermarket tracks for the MT100

Bobcat OEM tracks are engineered to match your MT100's specifications exactly and typically last 1,500 to 2,500 operating hours before needing replacement. They cost more upfront — usually $1,200 to $1,500 per track — but come with a warranty and are may provide to fit without modification. If you buy from a Bobcat dealer, they can also verify the part number for your specific machine year and serial number.

Aftermarket tracks from manufacturers like Camso, Prowler, and Maximizer cost $400 to $900 per track and fit the MT100 with no modification. Many owners report good results with aftermarket tracks, especially for light to moderate use. However, they may wear faster under heavy loading or in abrasive conditions, and warranty coverage varies by brand. Before buying aftermarket, check the product reviews specific to the MT100 and confirm the part number matches your machine's track size.

Step-by-step track replacement process

Start by parking the MT100 on level ground and engaging the parking brake. Lift one side of the machine using a floor jack placed under the frame (not the track or suspension), then find it with jack stands rated for at least 3,000 pounds. Never work under a machine supported only by a jack.

Locate the track tension bolts on the idler wheel assembly — usually two bolts on the rear of the track frame. Loosen these bolts to release tension on the track. Remove the bolts that hold the drive sprocket and idler wheel in place, then slide these components out. The old track should now slide off the rollers. Clean the roller path and inspect each roller, the sprocket teeth, and the idler wheel for cracks, flat spots, or excessive wear.

Install the new track by sliding it over the rollers, then reinstall the drive sprocket and idler wheel. Tighten the bolts hand-tight first, then use a torque wrench to tighten them to the specification in your MT100 manual — typically 40 to 60 foot-pounds depending on bolt size. Adjust the track tension by tightening the idler bolts until the track has about 1 inch of play when you lift it at the center. Lower the machine and repeat on the other side.

Tools and equipment you'll need

A floor jack rated for at least 3,000 pounds, two jack stands of the same rating, and a level work surface are essential. You'll also need a socket set, wrenches, a torque wrench, and a pry bar to help slide the track off. Some owners use a track puller tool (a specialized lever that costs $50 to $150) to make removal easier, though it's not required if you have patience and the right leverage.

Wear work gloves and steel-toed boots — tracks are heavy and can pinch fingers or crush toes. Have a helper on hand if possible; one person can operate the jack while the other guides the track. If you don't have a torque wrench, you can borrow or rent one from most tool rental shops for $10 to $20 per day.

When to replace tracks versus when to repair

Small cuts or punctures in the rubber can sometimes be patched with a track repair kit, which costs $30 to $100 and takes 30 minutes to an hour. However, if the damage is more than 2 inches long, if chunks of rubber are missing, or if the track is cracked all the way through, replacement is the only option. A damaged track will continue to shed rubber and can throw off the machine's balance, making it unsafe to operate.

If only one track is damaged, you can replace just that one, though many owners replace both at the same time to may support even wear and consistent performance. Mixing an old track with a new one can cause the machine to pull to one side and wear out the new track faster.

Finding the right replacement track for your MT100

The MT100 uses a 10-inch wide track, and the part number is usually printed on the side of the existing track or in your operator's manual. Write down this number before you shop — it ensures you get the exact fit. Bobcat dealers can look up the correct part by your machine's serial number, which is stamped on the frame near the engine.

You can order OEM tracks directly from a Bobcat dealer, through online equipment suppliers, or from used equipment marketplaces if you're looking for a lower-cost option. Aftermarket tracks are widely available through Amazon, eBay, and specialty equipment retailers. Compare shipping costs, as tracks are heavy and shipping can add $100 to $300 to your order. Some dealers offer free shipping on orders over a certain amount, or you can pick up locally to avoid delivery fees.

Common mistakes to avoid during replacement

The most common mistake is failing to inspect the undercarriage components before installing a new track. If the drive sprocket is worn, the idler wheel is cracked, or the rollers are flat-spotted, a new track will wear out in half the normal time. Take 15 minutes to look at each part while the track is off — it's much cheaper to replace a sprocket now than to buy another track in 500 hours.

Another mistake is over-tightening the track tension bolts. Too much tension puts stress on the idler wheel and sprocket, causing premature wear. Too little tension causes the track to slip and can throw it off the rollers. The goal is about 1 inch of vertical play at the center of the track — you should be able to lift it slightly by hand but not easily.

Finally, don't skip the torque wrench step. Bolts that are hand-tightened can loosen during operation, causing the track to shift and potentially come off. A torque wrench costs $20 to $50 and takes 2 minutes to use — it's worth the small investment.

Frequently Asked Questions

How long do Bobcat MT100 tracks last?

OEM tracks typically last 1,500 to 2,500 operating hours depending on the terrain and load. Aftermarket tracks may last 1,000 to 2,000 hours. Light use on smooth ground extends track life; heavy use on rocky or abrasive ground shortens it. Proper tension adjustment and regular undercarriage inspection also help tracks last longer.

Can I replace just one track on my MT100?

Yes, you can replace a single damaged track. However, mixing a new track with an old one causes uneven wear and can make the machine pull to one side. Most owners replace both tracks at the same time for consistent performance, even if only one is visibly damaged.

What's the difference between a 10-inch and 12-inch track for the MT100?

The MT100 uses a 10-inch wide track as standard. A 12-inch track is not a direct replacement and requires modifications to the frame. Stick with the 10-inch size unless you have a specific reason to change — and if you do, consult a Bobcat dealer about compatibility and frame modifications.

Do I need to replace the drive sprocket when I replace the track?

Not always, but inspect it closely. If the sprocket teeth are worn smooth, cracked, or chipped, replace it at the same time — a worn sprocket will damage a new track quickly. A replacement sprocket costs $200 to $400, which is less than buying another track prematurely.

How much does it cost to have a dealer replace both MT100 tracks?

Labor typically runs $1,500 to $3,000 for both tracks, depending on your location and the dealer. Add the cost of the tracks themselves — $800 to $3,000 for OEM parts, or $800 to $1,800 for aftermarket. Total cost at a dealer is usually $2,300 to $6,000 for a complete replacement on both sides.