What bore and stroke mean, and why they matter

Bore is the diameter of your engine's cylinder — how wide the hole is. Stroke is the distance the piston travels up and down inside that cylinder. Together, they determine your engine's displacement, which is the total volume of air and fuel the engine can draw in during one complete cycle. Displacement is measured in cubic centimeters (cc) or liters, and it affects how much power your engine can produce and how efficiently it runs.

You need these measurements if you're rebuilding an engine, shopping for performance parts, comparing engines, or trying to understand what "350 cubic inches" or "5.0 liters" actually means for your vehicle. The bore and stroke also tell you whether an engine is "oversquare" (bore larger than stroke, favoring high RPM power) or "undersquare" (stroke longer than bore, favoring low-end torque).

Key Takeaways

  • Bore is cylinder diameter in millimeters or inches; stroke is piston travel distance in the same units — both must be in matching measurements before you calculate.
  • Displacement in cubic centimeters equals bore² × stroke × 0.7854 × number of cylinders, divided by 1,000 for the final cc figure.
  • You can find bore and stroke in your owner's manual, on the manufacturer's spec sheet, or by measuring the engine block and crankshaft yourself if you have it apart.
  • An oversquare engine (bore larger than stroke) typically produces peak power at higher RPM; an undersquare engine peaks lower but builds torque sooner.

The formula for calculating displacement

The standard formula for displacement in cubic centimeters is:

Displacement (cc) = (Bore² × Stroke × π ÷ 4) × Number of Cylinders

In practical terms, most people use the simplified version: Bore² × Stroke × 0.7854 × Cylinders ÷ 1,000 = cc. The 0.7854 is a constant that accounts for the circular cross-section of the cylinder. All measurements must be in millimeters for this formula to work.

If your bore and stroke are in inches instead, use this formula: Bore² × Stroke × 0.5236 × Cylinders = cubic inches. Then multiply the result by 16.387 to convert cubic inches to cubic centimeters.

Example: A 4-cylinder engine with a 90 mm bore and 100 mm stroke would be: (90² × 100 × 0.7854 × 4) ÷ 1,000 = 2,544 cc, or roughly a 2.5-liter engine.

Where to find your engine's bore and stroke specifications

The easiest source is your vehicle's owner's manual or the manufacturer's technical specification sheet. These documents list bore and stroke for every engine option that came in your model year. You can also find this information on the engine block itself — manufacturers often cast the displacement or bore size directly into the metal.

Online resources like manufacturer websites, engine rebuild guides, and automotive databases (such as those maintained by engine suppliers) publish bore and stroke for most common engines. If you're working with an older or less common engine, a machine shop or engine rebuilder who specializes in that platform can provide the exact measurements.

If you have the engine apart or on a stand, you can measure bore directly with a bore gauge or dial caliper at the widest point of the cylinder wall. Stroke is measured from the crankshaft — it's half the distance from the bottom of the crankshaft throw to the top when the piston is at bottom dead center and top dead center.

Oversquare versus undersquare engines

An oversquare engine has a bore larger than its stroke. This design allows the piston to move faster and the engine to rev higher safely, which means peak power arrives at higher RPM. Oversquare engines are common in sports cars and performance applications where high-RPM horsepower matters more than low-end grunt.

An undersquare engine has a stroke longer than its bore. The longer stroke means the piston spends more time near the bottom of the cylinder, where pressure is highest, so torque builds earlier and peaks at lower RPM. Undersquare engines are typical in trucks, towing vehicles, and engines designed for efficiency at steady highway speeds.

A square engine has bore and stroke nearly equal. These are relatively rare in modern production engines but represent a middle ground between high-RPM capability and low-end torque.

Using bore and stroke to compare engines

Displacement alone doesn't tell you everything — a 5.0-liter V8 and a 5.0-liter turbocharged inline-four produce very different power curves. But bore and stroke help explain why. The V8 with a larger bore and shorter stroke will make peak power higher in the RPM range. The turbocharged four-cylinder, even at the same displacement, may have a longer stroke and will build torque lower.

When shopping for a replacement engine or performance upgrade, comparing bore and stroke helps you predict whether the engine will suit your vehicle's intended use. If you need an engine that pulls hard from a stop — for towing or off-road work — look for a longer stroke relative to bore. If you want an engine that revs freely and makes peak power at higher RPM, a larger bore and shorter stroke is the better choice.

You can also use bore and stroke to estimate compression ratio changes if you're modifying an engine. A larger bore with the same stroke increases displacement and can affect how the combustion chamber volume relates to the total cylinder volume, which changes compression ratio.

Common bore and stroke measurements for popular engines

EngineBore (mm)Stroke (mm)DisplacementType
Chevrolet 350 (5.7L V8)101.688.45.7LOversquare
Ford 7.3L Diesel V8104.8105.07.3LSquare
Honda K20Z3 (2.0L I4)87.084.02.0LOversquare
Cummins 5.9L Diesel I6102.0120.05.9LUndersquare

Frequently Asked Questions

Can I increase displacement by boring out my engine?

Yes — boring increases the cylinder diameter, which increases displacement. However, there are limits. The cylinder walls have a minimum thickness for strength, so you can only bore so far before you risk cracking the block. A machine shop can measure your block and tell you the maximum safe bore size, usually 0.030 to 0.060 inches larger than stock.

What's the difference between bore and cylinder head size?

Bore is the diameter of the cylinder itself. Cylinder head size refers to the valve sizes and port sizes in the head that sits on top of the block. A larger bore doesn't automatically mean larger valves — you can have a big-bore engine with small valves or a small-bore engine with large valves, though that would be unusual.

Does a bigger bore always mean more horsepower?

Not automatically. A larger bore allows higher RPM capability and can support more airflow, but horsepower depends on many factors: compression ratio, fuel quality, intake and exhaust design, and tuning. A well-tuned undersquare engine can make more power than a poorly tuned oversquare one at the same displacement.

How do I know if an engine will fit in my vehicle?

Bore and stroke don't determine physical size — a tall, narrow engine and a short, wide engine can have the same displacement but very different dimensions. Check the engine's overall length, width, and height against your engine bay, and verify that motor mounts, cooling systems, and exhaust routing will work. A machine shop or engine supplier familiar with your vehicle can advise on fitment.

What if my engine's bore and stroke aren't listed anywhere?

Contact an engine rebuilder or machine shop that specializes in your engine type — they have reference materials and can measure the block if needed. You can also reach out to the manufacturer's technical support line if the engine is still in production, or check enthusiast forums dedicated to your vehicle, where others may have already documented the specs.