What valve clearance means and why it matters on your SP702
Valve clearance is the small gap between the valve stem and the rocker arm on your Briggs & Stratton SP702 engine. This gap lets the valve fully close and prevents it from sticking or burning when the engine heats up. If the clearance is too tight, the valve won't seal properly and you'll lose compression. If it's too loose, the valve won't open far enough and your engine will run rough, lose power, or fail to start.
The SP702 is a single-cylinder, overhead-valve engine used in pressure washers, generators, and similar equipment. Because it's a small engine with tight tolerances, getting the valve clearance right is one of the most important maintenance tasks you can do yourself. A misadjusted valve will show up as hard starting, rough idle, loss of power, or excessive noise from the valve train.
Briggs & Stratton publishes specific clearance measurements for the SP702 in the engine's service manual. These measurements are not suggestions—they're the only settings that will let the engine run as designed. You'll need a feeler gauge (a thin metal blade that measures gaps) and about 15 minutes to check and adjust both valves.
Key Takeaways
- The SP702 requires intake and exhaust valve clearances to be set to the specifications in the Briggs & Stratton service manual for your specific engine serial number, as clearances can vary slightly between production runs.
- You must check valve clearance only when the engine is cold and the piston is at top dead center on the compression stroke, which you can find by aligning marks on the flywheel.
- A feeler gauge is the only accurate tool for this job—you slide the correct thickness blade into the gap between the valve stem and rocker arm until it fits snugly with light resistance.
- Intake valves typically run looser than exhaust valves on small engines, so do not assume both clearances are the same.
- If you cannot find the clearance specification for your exact engine, contact Briggs & Stratton directly with your engine model and serial number rather than guessing.
How to locate the correct clearance specification for your SP702
The Briggs & Stratton SP702 service manual is the only reliable source for your engine's valve clearance. You can find this manual in three ways: read it from the Briggs & Stratton website using your engine's model and serial number, order a printed copy from an authorized dealer, or contact Briggs & Stratton customer service directly at 1-800-233-3723 with your engine information.
When you contact Briggs & Stratton or search their website, have your engine's serial number ready. The serial number is stamped on the engine block and typically begins with the model number (SP702) followed by a series of digits. The manual will list two separate clearance measurements: one for the intake valve and one for the exhaust valve. Write both down before you start work, because you'll need to reference them repeatedly as you adjust each valve.
If you've lost the manual and cannot locate it online, many small-engine repair shops keep copies on file and can read you the specifications over the phone. This is faster than waiting for a manual to arrive and costs nothing if the shop is familiar with the SP702.
Preparing the engine and finding top dead center
Before you touch the valves, the engine must be completely cold. A warm engine will give you false readings because metal expands as it heats. Shut down the engine, let it sit for at least an hour, and touch the cylinder head to confirm it's cool to the touch.
Next, you need to position the piston at top dead center (TDC) on the compression stroke. This is the point where the piston is at its highest position and both valves are closed. To find TDC, remove the spark plug and look at the flywheel (the large wheel on the side of the engine). Briggs & Stratton engines have a mark on the flywheel and a corresponding mark on the engine block. Slowly rotate the flywheel by hand until these marks line up. This puts the piston at TDC.
If you cannot see the marks clearly, rotate the engine slowly with a wrench on the crankshaft bolt until you feel both valves go slack (loose) at the same time. This is the compression stroke at TDC. Do not use the starter motor to turn the engine—always rotate it by hand so you can feel when the valves are loose.
Checking and adjusting the intake valve
With the piston at TDC, the rocker arms should move freely and both valves should be closed. Start with the intake valve (the one closer to the carburetor side of the engine on most SP702 installations). Locate the rocker arm for the intake valve and look for the adjustment screw at the end of the rocker arm. This screw has a locknut that holds it in place.
Loosen the locknut with a wrench, holding the adjustment screw steady so it doesn't turn. Once the locknut is loose, insert your feeler gauge blade of the correct thickness (from your manual) between the valve stem and the rocker arm. The blade should slide in with light resistance—not so tight that you have to force it, and not so loose that it slides in freely. If the gap is too tight, turn the adjustment screw counterclockwise (out) to increase the gap. If it's too loose, turn the screw clockwise (in) to decrease the gap.
Make small adjustments—a quarter turn at a time—and recheck with the feeler gauge after each adjustment. Once the gap feels right, hold the adjustment screw steady and tighten the locknut firmly. Recheck the clearance one more time after tightening the locknut, because tightening sometimes shifts the screw slightly.
Checking and adjusting the exhaust valve
The exhaust valve is the second rocker arm, usually on the opposite side of the cylinder head from the intake valve. The adjustment procedure is identical: loosen the locknut, insert the correct feeler gauge blade (which will be a different thickness than the intake), and adjust the screw until the blade fits with light resistance.
Exhaust valves typically require a tighter clearance than intake valves on small engines, so do not assume both measurements are the same. If your manual specifies 0.005 inches for intake and 0.007 inches for exhaust, those are two different settings. Use the correct gauge blade for each valve.
After adjusting the exhaust valve, tighten its locknut and recheck the clearance. Once both valves are set and rechecked, reinstall the spark plug, close any covers you removed, and the job is complete.
What to do if you cannot find your engine's specifications
If you've searched the Briggs & Stratton website, called customer service, and checked with local dealers without finding your exact engine's clearance specification, do not guess. Running an engine with incorrect valve clearance can damage the valves, rocker arms, and cylinder head.
Your options are to contact Briggs & Stratton directly with your complete serial number and ask them to email or fax you the specification, order a service manual from an online retailer (usually $15 to $30), or take the equipment to a small-engine repair shop and have them check the clearance for you. A shop visit typically costs $50 to $100 for this single task, but it's cheaper than replacing valve components.
Some older SP702 engines may have been produced with slightly different clearance specifications than newer ones. This is another reason to get the specification for your specific serial number rather than relying on a general figure you find online.
Tools and materials you'll need
You need only a few items to check and adjust valve clearance. A feeler gauge set is essential—this is a set of thin metal blades in different thicknesses, usually ranging from 0.002 to 0.025 inches. A basic set costs $5 to $15 at any auto parts store or online. You'll also need two wrenches: one to hold the adjustment screw and one to turn the locknut. A 10mm and 12mm wrench will fit most SP702 engines, but check your manual to be sure.
A socket wrench or adjustable wrench on the crankshaft bolt helps you rotate the engine to find top dead center, though a large screwdriver or breaker bar will work if you don't have a socket. Finally, you may need a spark plug socket and ratchet to remove the spark plug, depending on your equipment's design.
Do not use a wire feeler gauge—the metal is too soft and will bend, giving you false readings. Always use a blade-type feeler gauge with a stiff metal blade.
Frequently Asked Questions
Can I check valve clearance while the engine is warm?
No. Metal expands when it heats up, so a warm engine will show you a larger gap than actually exists when the engine cools. Always wait at least an hour after the engine shuts down and confirm the cylinder head is cool to the touch before checking clearance.
What happens if I set the clearance too tight?
A tight clearance prevents the valve from closing fully, causing compression loss, hard starting, and rough running. Over time, the valve will overheat and burn, creating a permanent leak that no adjustment can fix. This requires replacing the valve.
What happens if I set the clearance too loose?
A loose clearance prevents the valve from opening far enough, reducing airflow and fuel flow into the cylinder. The engine will lose power, run rough, and may not start. You'll also hear a loud ticking or clacking noise from the valve train.
Do I need to adjust both valves every time I service the engine?
No. Check valve clearance once a year or every 100 hours of operation, whichever comes first. Most engines hold their clearance for years if they're maintained properly. You only need to adjust if the clearance has drifted outside the specification.
Can I use a different feeler gauge thickness if I don't have the exact one?
No. Using the wrong thickness will set the clearance incorrectly, and the engine will not run as designed. If you don't have the exact blade, buy a feeler gauge set that includes it, or borrow one from a repair shop.