What "submarine" means in lowrider culture

A submarine, or "sub," is a lowrider that can lower so far that the body nearly touches the ground—sometimes scraping it intentionally. The term comes from the visual effect: the car sits so low it looks like it's sinking. This is achieved through hydraulic suspension systems that replace or supplement the factory springs and shocks, allowing the driver to raise and lower the vehicle at will.

Building a submarine is different from routine maintenance because it requires replacing core suspension components and adding hydraulic pumps, cylinders, and plumbing. The work is specialized, expensive, and permanent—once you commit to hydraulics, you're changing how the car handles, rides, and performs. This guide explains what the build involves, what it costs in real terms, and what you need to know before starting.

Key Takeaways

  • A submarine build replaces your factory suspension with hydraulic cylinders controlled by a pump and switches, allowing you to lower the car on demand.
  • The hydraulic system itself costs between several hundred and several thousand dollars depending on quality and how many wheels you want to control independently.
  • Installation requires welding, fabrication, and plumbing work that most home mechanics cannot do safely—expect to pay a shop specializing in lowriders.
  • Submarine cars are not street-legal in most states without modifications, and even then, many jurisdictions restrict how low you can go or whether you can lower while driving.
  • The suspension changes how your car handles, brakes, and steers, and hydraulic systems require regular maintenance to prevent leaks and pressure loss.

The hydraulic suspension system and how it works

A submarine setup uses hydraulic cylinders mounted at each wheel (or selected wheels) to replace the coil springs and shocks. A hydraulic pump, usually electric and mounted in the trunk, pressurizes fluid through steel lines to these cylinders. The driver controls the system with switches inside the cabin, raising or lowering individual wheels or all four at once.

The most common configuration is a four-corner system, which lets you lower all four wheels independently or together. Some builders use a two-corner system (front or rear only) to reduce cost and complexity. The pump draws fluid from a reservoir, pressurizes it to 1,500 to 3,000 PSI depending on the setup, and holds pressure through accumulators so the car stays at your chosen height without the pump running constantly.

Quality matters significantly here. Cheap hydraulic kits use thin-wall cylinders and low-grade pumps that leak, lose pressure, and fail within months. Name brands used by established lowrider shops—such as Adex, Hoppos, or shop-built systems from known fabricators—cost more upfront but last years with proper maintenance. Budget kits from online retailers often fail because the components cannot handle the repeated pressure cycling.

What the build costs in parts and labor

Hydraulic system costs vary widely based on how many wheels you control and the quality of components. A basic four-corner kit from a reputable source runs $1,500 to $3,500 for parts alone. This includes the pump, cylinders, accumulators, lines, fittings, switches, and fluid. Two-corner systems cost $800 to $1,500. Budget kits sold online may advertise $300 to $600, but these typically fail within a year and end up costing more in replacement parts and labor to remove and reinstall.

Installation labor is where the real expense sits. A shop that specializes in lowriders will charge $2,000 to $5,000 or more to install a four-corner system, depending on your car's design and how much fabrication is needed. The work includes removing the factory suspension, welding mounting brackets, running hydraulic lines through the frame, installing the pump and reservoir, wiring the switches, and testing the system under load. This is not a weekend job for a home mechanic—it requires welding equipment, a lift, and knowledge of hydraulic pressure and safety.

Total cost for a quality submarine build ranges from $4,000 to $8,000 or higher. Some builders spend $10,000 or more if they add air suspension as a backup, upgrade to a larger pump, or customize the mounting brackets extensively. Before committing, get quotes from at least two shops that have built submarines before and ask to see completed cars.

Legal and safety issues you need to know

Submarine cars are illegal to drive on public roads in most U.S. states without modifications and inspections. Many states have laws against lowering a vehicle below a certain ride height (often 4 to 6 inches from the ground) or against allowing the body to touch the frame or ground. Some states ban hydraulic suspension entirely because it can affect braking and steering response.

Even in states or cities where lowriders are tolerated, you typically cannot lower the car while driving—the suspension must be raised to a legal height before moving. This means you need a way to raise the car quickly if you're stopped by police. Some builders install a manual override or a second pump system to raise the car on demand. Check your local vehicle code or contact your state's Department of Motor Vehicles before building to understand what's allowed in your area.

Hydraulic suspension also changes how your car brakes and steers. When the car is lowered, the suspension geometry changes, which can affect brake balance and steering response. The hydraulic system must be tuned so the car is stable and controllable at all heights. A poorly installed system can make the car unsafe to drive, even at legal heights. This is another reason to use an experienced shop rather than a budget installer.

Maintenance and long-term reliability

Hydraulic systems require regular maintenance to stay reliable. You need to check fluid levels monthly, inspect hoses and cylinders for leaks, and replace the fluid every two to three years depending on use. Leaks are the most common problem—even small weeps from fittings or cylinder seals add up and cause the system to lose pressure, so the car won't hold height.

Accumulators, which store pressurized fluid to keep the car at height without the pump running, have a limited lifespan. They typically last 5 to 10 years before the internal bladder fails and they stop holding pressure. Replacing an accumulator costs $200 to $400 in parts and labor. Pump seals and cylinder seals also wear over time, especially if the system is used frequently or exposed to dirt and moisture.

If you plan to drive the submarine regularly, budget $500 to $1,000 per year for maintenance and repairs. If you use it occasionally for shows or short cruises, maintenance costs are lower but the system still needs attention. Neglecting maintenance leads to leaks, pressure loss, and eventually a car that won't lower or raise—and then you're paying a shop to diagnose and fix the problem.

Alternatives if you want a low-riding look without hydraulics

If the cost and complexity of hydraulics concern you, there are other ways to lower a car. Air suspension systems use compressed air instead of hydraulic fluid, which some builders prefer because air is cleaner and leaks are less messy. However, air suspension is more expensive upfront and requires an air compressor and dryer, adding another $1,000 to $2,000 to the build.

Static lowering—using lowering springs, coilovers, or a custom frame—is the cheapest option and requires no pumps or switches. You lower the car once during installation and it stays at that height. The downside is you lose the ability to raise it for legal driving or to clear speed bumps and driveways. A static lowering kit costs $300 to $800 in parts and $500 to $1,500 in labor, making it a fraction of the hydraulic cost.

Some builders combine approaches: they use static lowering for the look and add a small hydraulic system just for the front wheels, which lets them raise the nose slightly for legal driving while keeping the rear low. This hybrid approach costs less than a full four-corner system but gives you some of the flexibility of hydraulics.

Choosing a shop and what to ask before you start

Finding a shop that builds submarines well is critical. Ask for references and photos of completed cars. Visit the shop in person and look at their work—good shops have a portfolio of cars they've built and can show you how their systems perform. Ask how long they've been building lowriders, whether they do their own welding and fabrication, and what warranty they offer on their work.

Before signing a contract, ask the shop to explain the system they'll install: How many wheels will it control? What pump and cylinder brands will they use? What's the maximum pressure? How long will installation take? What's included in the price, and what costs extra? A good shop will answer these questions clearly and put the details in writing.

Also ask about legal compliance. Does the shop know your state's lowrider laws? Can they help you understand what's legal in your area? Will they install a manual raise system so you can lift the car if needed? A shop that understands the legal landscape will save you from building something you can't legally drive.

Frequently Asked Questions

Can I install a submarine system myself in my garage?

Not safely. The work requires welding to attach cylinders to the frame, hydraulic line fabrication and pressure testing, and electrical work to wire the pump and switches. A mistake in any of these areas can cause leaks, loss of pressure, or electrical fire. Unless you have professional welding and hydraulic experience, hire a shop.

How low can a submarine actually go?

A well-built system can lower the car until the body sits 2 to 4 inches from the ground, with the wheels still turning. Some cars go lower, but at extreme heights the suspension geometry breaks down and the car becomes unsafe. Legal limits vary by state but typically allow 4 to 6 inches minimum ride height on public roads.

Will a submarine system hurt my car's resale value?

Yes, in most cases. Hydraulic suspension is a permanent modification that appeals to a small group of buyers. Most used car buyers want a car that drives normally, and a submarine is a niche vehicle. If you plan to sell the car later, expect to lose money on the hydraulic investment.

How often do hydraulic systems break down?

A quality system installed by a reputable shop and maintained regularly should run for years without major problems. Budget systems and neglected systems fail within months. The most common failures are slow leaks from hose fittings and cylinder seals, which cause the car to gradually lose height. Regular inspections catch these early.

Can I raise the car while driving if I get pulled over?

In most states, no—you must raise the car before you start driving. Some shops install a manual pump or a second electric pump that lets you raise the car quickly at a stoplight, but this is a workaround, not a legal solution. Check your local laws and ask your shop what's allowed in your area.