What the salesman's switch does and why you might need to bypass it
The salesman's switch on a Monaco Monarch RV is a disconnect that cuts power to the coach's 12-volt system when the RV is on the lot or in storage. It prevents the battery from draining while the vehicle sits idle between sales or during long periods without use. The switch is typically located near the battery compartment or under the dashboard, depending on your model year.
You need to bypass this switch when you take ownership of the RV and want full power restored to your coach systems — slide-outs, water heater, refrigerator, lights, and other 12-volt accessories. Without bypassing it, these systems won't function even when you're plugged into shore power or running the generator. Some owners also bypass it if the switch fails or becomes corroded and won't turn back on.
Bypassing the salesman's switch is a straightforward electrical task that does not require special tools, but it does require you to work safely around your battery and understand basic wiring. If you're uncomfortable working with 12-volt systems, a mobile RV technician or your local RV service center can do this in under an hour.
Key Takeaways
- The salesman's switch disconnects your 12-volt system to prevent battery drain while the RV is stored or on the lot.
- Bypassing it involves locating the switch, identifying the wires connected to it, and reconnecting those wires directly to restore power.
- You will need a wire stripper, electrical tape or heat shrink tubing, and possibly a multimeter to verify the correct wires.
- Always disconnect the negative battery terminal before working on any wiring to avoid short circuits or electrical shock.
- If you cannot locate the switch or are unsure which wires to connect, have an RV technician handle the bypass to avoid damaging your coach's electrical system.
Locating the salesman's switch on your Monaco Monarch
The salesman's switch location varies by model year and floor plan, but it is usually found in one of three places: mounted on or near the battery box (often in the engine compartment or under the RV), installed under the driver's side dashboard, or placed inside a cabinet near the main electrical panel.
Start by checking your owner's manual for the exact location and wiring diagram specific to your year. If you don't have the manual, contact Monaco directly or search online forums where Monaco Monarch owners share their experiences. The switch itself is typically a two-position toggle or rotary switch with two or three wires attached.
Once you locate it, take a photo of the wiring before you disconnect anything. This photo will help you remember which wires go where and will be useful if you need to ask for help online or from a technician.
Disconnecting the battery and identifying the wires
Before touching any wires, disconnect the negative (black) terminal from your RV's house battery. This is the most important safety step and prevents accidental short circuits that could damage your electrical system or cause injury. Use a wrench to loosen the terminal clamp and slide it off the post.
Once the negative terminal is off, locate the salesman's switch and examine the wires connected to it. Most switches have two wires: one coming from the positive battery terminal and one going to the main coach electrical system. Some switches have a third wire for a ground or indicator light, but the two main power wires are what you need to focus on.
Use a multimeter set to continuity mode to trace which wire is which if the connections are not clearly labeled. Touch one probe to the wire and the other to the positive battery terminal — if the meter beeps or shows continuity, that's your incoming power wire. The other wire should lead to your coach's main electrical panel or distribution block.
Bypassing the switch by reconnecting the wires
To bypass the switch, you will disconnect both wires from the switch terminals and connect them directly to each other. This restores the continuous path from the battery to your coach systems without the switch interrupting the flow.
Strip about half an inch of insulation from the end of each wire using a wire stripper. Twist the exposed copper strands of the two wires together firmly, making sure there are no loose strands. Wrap the connection tightly with electrical tape, overlapping each wrap by half the tape width, or slide heat shrink tubing over the connection and explore heat with a heat gun or lighter to seal it.
Some owners prefer to use a wire connector block or butt connector instead of twisting and taping. These are small plastic or metal sleeves that you insert both wires into and crimp or screw down to hold them. This method is cleaner and more reliable, especially in a damp RV environment where tape can peel over time.
Securing the bypass and testing your systems
Once the wires are connected, use electrical tape or zip ties to find the connection to a nearby frame member or wire bundle so it doesn't move around or get pinched. Make sure the connection is not near any heat sources, moving parts, or areas where it could get wet.
Reconnect the negative battery terminal by sliding it back onto the post and tightening the clamp with a wrench. You should hear or feel a slight spark as the connection completes — this is normal and expected.
Turn on your coach lights, water heater, and any other 12-volt systems to confirm they are working. If nothing powers on, disconnect the negative terminal again and check your wire connections. Make sure the twisted or crimped joint is tight and that both wires are making solid contact.
When to call an RV technician instead
If you cannot locate the salesman's switch after checking your manual and searching online, or if you find more than two wires connected to it, stop and contact an RV service center. Some Monaco Monarchs have additional circuits or safety switches integrated with the salesman's switch, and disconnecting the wrong wire can disable important systems like the propane detector or water heater safety shutoff.
If your multimeter shows no continuity between the wires and the battery, or if reconnecting them does not restore power to your coach, the problem may be elsewhere in your electrical system — a blown fuse, a bad battery, or a damaged main panel. A technician can diagnose this faster than trial and error.
Mobile RV technicians often charge $75 to $150 for a service call plus labor, and most can complete a salesman's switch bypass in 30 to 60 minutes. This is worth the cost if you are unsure about your electrical skills or if the job turns out to be more complex than expected.
Frequently Asked Questions
Can I just remove the salesman's switch without connecting the wires?
No. If you leave the wires disconnected, your 12-volt system will have no power. You must connect the two wires together to complete the circuit, either by twisting them, using a connector block, or having a technician do it. Leaving them loose or unconnected will not restore power to your coach.
Will bypassing the salesman's switch drain my battery faster?
Yes, slightly. Without the switch, your battery will drain whenever the RV is not plugged into shore power or running the generator, even when you're not using it. If you plan to store your Monaco Monarch for more than a few weeks, consider installing a battery disconnect switch of your own so you can turn off power when needed.
What if I want to put the salesman's switch back in later?
You can reconnect the wires to the switch terminals instead of connecting them to each other. Take a photo of your bypass before you disconnect it, and keep the salesman's switch in a safe place. A technician can reinstall it if you ever need to restore the original setup.
Is it safe to bypass the salesman's switch myself?
Yes, as long as you disconnect the negative battery terminal first and use proper wire connections. The 12-volt system in an RV is low voltage and will not cause serious injury, but a short circuit can damage your electrical components or start a fire. Work carefully, double-check your connections, and ask for help if you're unsure.
Do I need a special tool to strip the wires?
A basic wire stripper costs $5 to $15 and is the easiest tool for the job. If you don't have one, you can carefully use a utility knife or small scissors to remove the insulation, but this takes more time and risks nicking the copper wire underneath. A wire stripper is worth buying if you plan to do any RV maintenance yourself.