What the salesman's switch does and why you might need to bypass it

The salesman's switch on a Monaco RV is a disconnect that cuts power to the coach's 12-volt system when the RV is parked on a dealer lot. It prevents the battery from draining while the vehicle sits unsold, and it also disables the engine start in case a potential buyer accidentally turns the key. Once you own the RV, this switch becomes an obstacle — it blocks power to your water heater, refrigerator, slide-outs, and other systems even when you want them running.

Bypassing it means restoring normal 12-volt operation so you can use all coach systems without the switch blocking them. This is a straightforward electrical task that takes about 30 minutes and requires basic tools. The switch itself is usually mounted under the driver's side dashboard or inside a cabinet near the main battery disconnect.

Key Takeaways

  • The salesman's switch cuts 12-volt power to prevent battery drain and accidental engine start on dealer lots, but blocks your systems once you own the RV.
  • Locate the switch under the driver's side dashboard or in a nearby cabinet, then trace the wires to identify which circuit it controls.
  • Bypass it by running a new wire directly from the battery positive terminal to the load side of the switch, or by removing the switch entirely and splicing the wires together.
  • Always disconnect the negative battery terminal before working on any wiring, and use a fuse holder rated for the circuit amperage to protect the new bypass wire.
  • If you are uncomfortable working with 12-volt wiring, a mobile RV technician can complete this job for $100 to $300 depending on your location.

Locating the salesman's switch in your Monaco

The salesman's switch is usually mounted on the driver's side of the dashboard, either under the steering column or inside the cabinet that houses the main battery disconnect. Some Monaco models place it in the engine bay near the battery, though this is less common. Check your owner's manual first — it should show the exact location for your model year.

If you cannot find it in the manual, look for a small toggle or rocker switch with two wires running to it, positioned near other electrical controls. It will be labeled "salesman's switch" or sometimes "dealer switch." Trace the wires back to see where they connect — one wire comes from the positive battery terminal or a fused circuit, and the other goes to the coach's main 12-volt distribution panel.

Disconnecting the battery before you start

Always disconnect the negative battery terminal first. This prevents accidental shorts and protects you from electrical shock while you work. Locate the negative terminal on your coach battery (usually marked with a black cable or a minus sign), loosen the terminal nut with a wrench, and slide the cable off. Do not touch any other wiring until this is done.

Leave the negative terminal disconnected for the entire job. Even if you finish the bypass wiring, do not reconnect it until you have double-checked all your connections and made sure no bare wires are touching metal parts of the RV frame.

Two methods to bypass the switch

The first method is to run a new wire directly from the positive battery terminal to the load side of the switch (the side that goes to the coach systems). This keeps the switch in place but makes it inert — power flows around it instead of through it. Use 10-gauge or 8-gauge wire depending on the circuit amperage, and install a fuse holder rated for that amperage within 18 inches of the battery. This method is safer because the fuse protects the new wire if something goes wrong.

The second method is to remove the switch entirely and splice the two wires together using a waterproof butt connector or solder joint. This is faster but leaves no protection if the wires short. If you choose this route, wrap the connection in electrical tape and heat-shrink tubing, then find it so it cannot move or rub against sharp edges.

Most RV owners prefer the first method because it adds a layer of safety. The fuse will blow if the circuit draws too much current, protecting the battery and wiring from fire or damage.

Running the bypass wire and installing the fuse

Strip about half an inch of insulation from the positive battery terminal wire and the load-side wire of the salesman's switch. Measure the distance from the battery to the switch location and cut your new wire about 2 feet longer than that measurement — you need slack to work with. Strip half an inch from each end of the new wire.

Crimp a ring terminal onto one end of the new wire and bolt it to the positive battery terminal, using the same bolt that holds the original cable. Crimp another ring terminal onto the other end and connect it to the load-side wire of the salesman's switch using a butt connector or solder joint. Install the fuse holder on the new wire within 18 inches of the battery, and insert a fuse rated for the circuit amperage — usually 30 to 50 amps for a coach 12-volt system, but check your RV's wiring diagram to be sure.

Route the new wire along the existing wire harness using cable ties or electrical tape. Keep it away from moving parts, heat sources, and sharp edges. Once everything is connected, reconnect the negative battery terminal and test your systems — the water heater, refrigerator, and other 12-volt loads should now work without the salesman's switch blocking them.

Testing your work and troubleshooting

Turn on the ignition and check that the dashboard lights come on. Open the refrigerator and listen for the cooling fan. Turn on the water heater and feel the heating element to confirm it is warming up. If any system does not work, turn off the ignition and check your connections — a loose crimp or a blown fuse is the most common cause.

If the fuse blows when ready after you reconnect the battery, you have a short circuit. Disconnect the negative terminal again, remove the fuse, and inspect the new wire for damage or contact with metal. Check that the ring terminals are tight and that no bare wire is exposed. Once you find and fix the short, install a new fuse and test again.

When to call a technician instead

If you are not comfortable working with 12-volt wiring, or if your Monaco has a complex electrical system with multiple switches and relays, a mobile RV technician can do this job. Expect to pay $100 to $300 depending on your location and how long it takes to locate the switch. Call ahead and describe your RV model and year so the technician can bring the right tools and fuses.

Some RV service centers also offer this as a standard post-purchase service, especially if you bought the Monaco from a dealer. Ask whether it is included in your warranty or service package before you pay out of pocket.

Frequently Asked Questions

Will bypassing the salesman's switch drain my battery faster?

No. The switch was only needed to prevent drain while the RV sat on a dealer lot. Once you own it, your battery will drain at the same rate whether the switch is in place or bypassed — the difference is that now you can use your systems instead of being locked out of them.

Can I just remove the switch and leave the wires disconnected?

No. Leaving the load-side wire disconnected cuts power to your entire 12-volt coach system. You must either splice the two wires together or run a bypass wire to restore power. Disconnecting one wire without connecting it to anything will disable your water heater, refrigerator, lights, and slide-outs.

What amperage fuse should I use for the bypass wire?

Check your Monaco's wiring diagram or owner's manual for the main coach 12-volt circuit amperage. Most RVs use a 30 to 50 amp fuse for this circuit. If you cannot find the spec, use a 40 amp fuse as a starting point — if it blows repeatedly, you may have a short that needs repair before you proceed.

Do I need to tell my insurance company I bypassed the switch?

No. The salesman's switch is a dealer-specific feature, not a safety system. Bypassing it does not affect your coverage or require notification to your insurer.

Can I reinstall the salesman's switch later if I sell the RV?

Yes, but most buyers will want it bypassed anyway. If you kept the original switch and wiring intact, a technician can reconnect it in about 15 minutes. However, most people straightforward leave the bypass in place because it is cleaner and more reliable than the original switch.