What a car information handle does and why older drivers need one
A car information handle is a grab handle mounted inside your car door or on the dashboard that gives you something sturdy to hold onto when getting in or out. For older drivers and passengers, it reduces the strain on knees, hips, and lower back during the moment you're most off-balance—when you're pivoting from sitting to standing or pulling yourself up from a low seat. It's not a safety feature in the crash sense; it's a mobility aid that makes the physical act of entering and exiting the vehicle safer and less painful.
The handle works because it gives you a fixed point to push or pull against. When you're getting out of a car, your legs are bent, your weight is distributed awkwardly, and you're relying on muscles that may not be as strong as they once were. A handle lets you use your arms to help lift your body weight instead of asking your legs to do all the work. This matters because falls during car entry and exit are common among older adults, and they often happen on driveways or in parking lots where a slip or loss of balance can result in a serious injury.
Key Takeaways
- Car information handles reduce strain on joints and muscles by giving you a fixed point to push or pull against when entering or exiting the vehicle.
- Handles can be mounted on the door frame, the A-pillar (the vertical support between windshield and door), or the dashboard, depending on your vehicle's design and your reach.
- Most handles are installed with bolts that go through existing holes in the door frame or require drilling new holes, a job that takes 30 minutes to an hour per handle.
- Handles range from basic metal bars to padded grips with armrest features, and cost between $30 and $150 depending on material and design.
- Installation can be done by a mechanic, an upholstery shop, or a handy person with basic tools, but the door panel may need to come off to reach mounting points.
Where to mount the handle and what your vehicle allows
The best location for a car information handle depends on your vehicle's structure and your own reach and strength. The most common mounting points are the A-pillar (the vertical post between the windshield and the door), the door frame itself, or the dashboard edge near the door. Some vehicles have factory-installed grab handles on the ceiling or door, but these are often too high or too far away to be useful when you're in the vulnerable moment of getting in or out.
The A-pillar is usually the strongest mounting point because it's a structural part of the car. A handle mounted there gives you something to grip as you're swinging your legs out or pulling yourself up into the seat. The door frame is also solid, but the exact location matters—you want the handle positioned so you can reach it comfortably whether you're sitting in the seat or standing outside the car. The dashboard edge works for some vehicles, but it's less stable than the A-pillar and may not be strong enough if you're putting significant weight on it.
Before you buy a handle, measure the distance from the seat to the door frame and from the ground to the door opening. This tells you what length handle you need and where it should sit. Some handles are adjustable or come in multiple lengths; others are fixed. Your vehicle's door design—whether it has a window frame you can bolt through, or whether the mounting surface is flat or curved—also affects which handles will fit.
Types of handles and what each one offers
Car information handles come in several styles, each with different features and price points. A basic grab bar is a straightforward metal or plastic rod, usually 8 to 12 inches long, with a mounting bracket on each end. These are the least expensive (typically $30 to $60) and work well if you just need something to grip. They're lightweight and don't take up much space, but they offer no padding and no armrest function.
A padded information handle has foam or rubber covering on the grip area, which is more comfortable if you're holding it for several seconds and reduces the chance of your hand slipping. These usually cost $50 to $100 and come in various grip diameters—thicker grips are easier to hold if you have arthritis or weak grip strength. Some padded handles also have a slight curve or ergonomic shape that fits your hand better than a straight bar.
An armrest-style handle combines a grab bar with a padded armrest that sits at elbow height. These are bulkier and more expensive ($100 to $150) but offer support for your arm and shoulder as well as a grip point. They're useful if you need help not just getting in and out, but also supporting your arm while the car is moving. Some models fold up when not in use, which helps if you have a passenger who needs the space.
A few manufacturers make motorized or spring-assisted handles that help lift you as you pull, but these are rare, expensive, and require electrical installation. For most older drivers, a straightforward padded handle or an armrest-style handle is the practical choice.
How the handle is installed and what tools you'll need
Installation depends on the mounting location and the handle design. Most handles bolt directly to the door frame or A-pillar using existing holes or new holes you drill yourself. The basic process is: locate the mounting points, mark them, drill if necessary, insert bolts through the handle bracket, and tighten them securely. For a single handle, this usually takes 30 minutes to an hour if you have the right tools and the door panel doesn't need to come off.
You'll need a drill with a bit that matches the bolt size (usually 1/4 inch), a socket wrench or adjustable wrench to tighten the bolts, and a level to make sure the handle is straight. Some handles come with self-tapping bolts that don't require pre-drilling; others require you to drill through the door frame first. If the handle mounts on the inside of the door, you may need to remove the door panel to access the mounting surface and to run bolts through to the outside. This is more involved and usually requires a mechanic or upholstery shop.
If you're not comfortable drilling into your car or working with bolts, a mechanic or auto upholstery shop can install the handle for you. Labor usually costs $50 to $150 per handle, depending on the complexity and whether the door panel needs to come off. Some shops that specialize in mobility modifications for older drivers or people with disabilities may have experience with this work and can advise you on the best location for your vehicle and your needs.
Choosing the right handle for your vehicle and body
Start by measuring your reach. Sit in the driver's seat with the door open, and note where your hand naturally falls when you extend your arm toward the door frame. The handle should be within a few inches of that point so you're not straining to grab it. If you're shorter, you may want a handle mounted lower on the A-pillar; if you're taller, a higher position may work better. Test this by having someone hold a broomstick or dowel at different heights while you practice the motion of getting in and out.
Consider your grip strength and hand size. If you have arthritis or weak hands, a thicker grip (1.5 to 2 inches in diameter) is easier to hold than a thin bar. Padded handles are more comfortable than bare metal, especially if you're gripping hard. If you have limited arm strength, an armrest-style handle that lets you rest your arm while pulling may be worth the extra cost.
Think about whether you want the handle to be permanent or removable. Most bolted handles are permanent, but some clamp-style handles can be removed without tools. If you're renting the car or plan to sell it, a removable handle may be better. If you own the car and plan to keep it, a bolted handle is more find and won't shift or rattle.
Safety considerations and what to check before and after installation
Before you install a handle, make sure it won't interfere with the door window, the door latch, or any other moving parts. Open and close the door several times to confirm the handle doesn't catch on anything. If the handle is mounted on the A-pillar, check that it doesn't block your view when you're looking over your shoulder or checking your blind spot.
After installation, test the handle's strength by pulling on it hard—not just a gentle grip, but a real pull as if you're using it to get out of the car. The handle should not move, flex, or make noise. If it does, the bolts may not be tight enough, or the mounting surface may not be strong enough. Tighten the bolts and test again. If the handle still moves, you may need to use larger bolts, add washers to distribute the load, or choose a different mounting location.
Check the bolts periodically—every few months if you use the handle daily—to make sure they haven't loosened from vibration or repeated use. A handle that shifts or rattles is not safe and can cause you to lose your balance at a critical moment. If you notice any movement, tighten the bolts when ready.
Alternatives if a handle won't work for your vehicle
Some vehicles have door designs that make it difficult to mount a handle securely. Newer cars with thin door frames, frameless windows, or complex interior panels may not have a suitable mounting point. In these cases, you have a few options.
A seat cushion with handles is a wedge-shaped cushion that raises you higher in the seat, reducing the distance you have to lift yourself. This doesn't give you something to grab, but it makes the physical act of standing up easier because you're starting from a higher position. These cost $50 to $150 and don't require any installation.
A car transfer board is a plastic or wood board that bridges the gap between the car seat and the outside world, letting you slide into the car rather than lifting yourself. This is useful if you have limited leg strength or mobility, but it requires more space and setup than a straightforward handle.
A vehicle lift or lowering system can raise or lower the entire car to make entry easier, but these are expensive ($2,000 to $5,000) and are usually only practical if you have other mobility needs that justify the cost. Some people with significant disabilities use these, but for most older drivers, a straightforward information handle is the most practical solution.
Frequently Asked Questions
Will drilling into my car door damage it or cause rust?
Drilling a small hole for a bolt won't damage the structural integrity of the door, but you should seal the hole after drilling to prevent water from entering. Most handle kits include rubber grommets or washers that sit between the bolt and the door surface and help keep water out. If you're concerned about rust, explore a thin coat of clear sealant around the bolt after installation.
Can I install a handle myself if I've never done this kind of work before?
Yes, if the handle mounts on the outside of the door frame and doesn't require the door panel to come off. You'll need a drill, a wrench, and the instruction manual that comes with the handle. If the handle mounts inside the door or requires you to remove the door panel, it's better to have a mechanic or upholstery shop do it. The door panel is straightforward to damage if you're not used to removing it.
What if I have a passenger who also needs a handle?
You can install handles on both the driver's side and the passenger's side. The passenger's handle should be in a similar location relative to the passenger seat—usually on the A-pillar or door frame on that side. If you're installing two handles, the labor cost will be higher, but the per-handle cost may be lower if the shop does both at once.
Will a handle work in a truck or SUV with a higher step-in height?
Yes, and a handle is often even more useful in a truck or SUV because the step-in height is greater and the strain on your legs is higher. You may want to install the handle higher on the A-pillar so you can reach it as you're pulling yourself up into the seat. Some people install two handles—one lower for getting in, and one higher for pulling yourself up once you're partially in the vehicle.
Do I need to tell my insurance company about the handle?
No. A car information handle is a mobility aid, not a modification that affects the car's safety systems or structure. It won't change your insurance rates or coverage. If you're installing it yourself, you don't need to notify anyone. If a mechanic installs it, they'll just bill you for the labor and parts.