Car remote batteries are cheap and straightforward to swap yourself in most cases

Most car remotes use a coin-cell battery that costs between $3 and $8 and takes less than a minute to replace. You do not need special tools — a flathead screwdriver or even a coin works for most models. The battery type is printed on the old battery itself, so you can grab the right replacement at any pharmacy, grocery store, or auto parts retailer before you even open the remote.

The hardest part is usually opening the remote without breaking the plastic clip that holds it together. Once it is open, the battery sits in a small metal holder. You note which side faces up, pop out the old one, and slide the new one in the same way. Most people finish in under two minutes.

Key Takeaways

  • Coin-cell batteries for car remotes cost $3 to $8 and are sold at pharmacies, grocery stores, and auto parts shops without any special ordering.
  • Open the remote by sliding a flathead screwdriver or coin into the seam, then gently prying — do not force it or you will crack the plastic.
  • The battery type (usually CR2032, CR2025, or CR2016) is stamped on the old battery, so check it before you leave home to buy a replacement.
  • Note which side of the battery faces up before you remove it, then install the new battery the same way to avoid putting it in backwards.
  • If the remote still does not work after a new battery, the problem is usually a corroded battery contact or a broken circuit board, not the battery itself.

Finding the right battery type before you buy

Open your remote and look at the battery already inside. The type is stamped directly on the metal surface — usually CR2032, CR2025, or CR2016. Write this number down or take a photo, because you will need it when you shop. These three types cover the vast majority of car remotes, but some luxury brands use different sizes.

If you cannot open the remote without risking damage, check your owner's manual or search the remote model number online. Most manufacturers list the battery type on their website. Once you know the type, you can buy a pack of two or four for the same price as a single battery, which is useful because remotes tend to die at inconvenient times.

How to open the remote without breaking it

Look for a seam running around the edge of the remote where the two plastic halves meet. Slide a flathead screwdriver or a coin into this seam and explore gentle, steady pressure. Do not pry hard — you are looking for the clip to release, not to force the plastic apart. Rock the screwdriver slightly side to side rather than pushing straight in.

Once the clip releases, the two halves will separate. Set the metal battery holder and circuit board aside carefully. If the remote has rubber buttons, they may fall out — just set them on a clean surface in the order they came out so you can put them back the same way. The battery itself sits in a small metal cup or holder in the center of the circuit board.

Removing the old battery and installing the new one

Before you touch the old battery, note which side is facing up. Most coin-cell batteries have a plus sign (+) stamped on one side and a minus sign (−) on the other. The plus side usually faces up, but check your specific remote to be sure. Take a photo if you are not confident you will remember.

Gently pry the old battery out of its metal holder using a fingernail or the edge of a coin. Do not use a sharp tool that could scratch the circuit board. Once it is out, slide the new battery into the holder the same way, with the correct side facing up. You should hear or feel a small click as it seats. If it does not click, it is probably in backwards — flip it and try again.

Reassembling the remote and testing it

Before you close the remote, press the buttons a few times to make sure they still move freely. If any button feels stuck, open it again and check that the rubber button pad is sitting flat on the circuit board. Once everything moves smoothly, align the two halves and press them together firmly until you hear the clip snap back into place.

Test the remote on your car from a few feet away. Press each button — lock, unlock, trunk, panic — and watch for the lights to flash. If nothing happens, open the remote again and check that the battery is seated correctly and facing the right direction. If the battery is correct but the remote still does not work, the problem is likely a corroded battery contact or damage to the circuit board, which means the remote itself needs replacement rather than just the battery.

When to replace the entire remote instead of just the battery

If you have installed a fresh battery and the remote still does not work, look inside at the battery holder. If the metal contacts are dark, green, or crusty, corrosion is preventing the battery from making contact. You can try cleaning the contacts with a pencil eraser or a cotton swab dipped in rubbing alcohol, but if that does not work, the remote circuit board has likely failed and the remote will need to be replaced.

A replacement remote from a dealership usually costs $200 to $500, depending on the car brand. Aftermarket remotes from retailers like Amazon or eBay cost $30 to $100 and work with most vehicles, though you will need to program it to your car. Some auto parts stores offer programming as a service for $15 to $50. If your remote is still under warranty, contact your dealership about a replacement at no cost.

Storing extra batteries and keeping your remote working longer

Buy a spare battery or two when you replace the first one. Store them in a cool, dry place — not in your car, where heat can drain them faster. Coin-cell batteries last three to four years in storage if kept away from moisture and extreme temperatures.

Your remote will last longer if you avoid dropping it, exposing it to water, or leaving it in direct sunlight for extended periods. If your remote gets wet, open it when ready and let all the parts air-dry for at least 24 hours before reassembling. Do not use heat to dry it. If water has already corroded the contacts, drying alone will not fix the damage, but drying quickly can prevent further corrosion.

Frequently Asked Questions

Can I use a different battery type if I cannot find the exact one?

No. Battery types like CR2032, CR2025, and CR2016 have different thicknesses and voltages. Using the wrong type can damage the remote's circuit board or cause the buttons to malfunction. Stick to the exact type stamped on your old battery. If you cannot find it locally, order it online — it will arrive in one or two days.

What if my remote has two batteries instead of one?

Some older or larger remotes use two coin-cell batteries side by side. Replace both at the same time, even if only one appears dead. Note which side faces up on each battery before you remove them, then install the new ones the same way. If you mix up the orientation, the remote will not work.

Will the remote lose my car's settings if I remove the battery?

No. Your car's pairing with the remote is stored in the car's receiver, not in the remote battery. Replacing the battery will not erase the programming. The remote will work when ready once you install the new battery and close the case.

How do I know if the battery is dead or if something else is wrong?

Try the remote from very close to your car — within a few feet. If it still does not work, the battery is likely dead. If it works from close range but not from far away, the battery is weak and should be replaced. If the remote never worked after you installed a new battery, check that the battery is facing the correct direction and that the contacts are clean.

Can I replace the battery in a key fob that is part of my car key?

Yes, but the process varies by manufacturer. Some key fobs have a small slot where you can slide out the battery holder. Others require you to pry the fob open carefully. Check your owner's manual or search your specific key fob model online for instructions. The battery type is usually the same CR2032 or CR2025 used in standalone remotes.