Chainsaw chains are sized by three measurements: pitch, gauge, and drive link count
A chainsaw chain is not one size. The chain that fits your saw depends on three separate measurements working together. Pitch is the distance between the rivets that hold the chain together, measured in fractions of an inch. GaugeDrive link count is straightforward how many drive links are on the whole chain. All three have to match your saw, or the chain will not fit, will not cut properly, or will damage your bar.
The reason this matters is that a chain that looks similar to yours might have a different pitch or gauge, and putting it on anyway will either jam in the bar or rattle loose. A loose chain can derail during cutting, which is a serious safety problem. Getting the right size takes five minutes if you know where to look.
Key Takeaways
- Pitch, gauge, and drive link count are three separate measurements, and all three must match your saw's bar for the chain to work safely.
- Your owner's manual lists the correct chain size for your model, and this is the fastest way to find what you need.
- The pitch and gauge are stamped on the side of your current chain, so you can read them directly without guessing.
- Drive link count is found by counting the metal teeth on the chain or by checking your manual, since it varies by bar length.
- Mixing pitch or gauge sizes will cause the chain to jam, rattle, or damage the bar, so verify all three numbers before buying a replacement.
How to read pitch on your current chain
Pitch is the distance between the center of one rivet and the center of the next rivet on the chain. It is stamped on the side of most chains and is expressed as a fraction: 1/4 inch, 3/8 inch, or .325 inch are the most common sizes. If you cannot see the stamp clearly, you can measure it yourself by measuring the distance between three rivets and dividing by two.
The pitch is critical because the sprocket on your saw's engine is cut to match one specific pitch. If you put a chain with the wrong pitch on your saw, the sprocket teeth will not catch the drive links properly. The chain will either slip and not cut, or it will bind up and stall the engine. Pitch is not something you can adjust or work around — it has to match exactly.
Most homeowner saws use either 3/8 inch pitch or .325 inch pitch. Professional or larger saws often use 3/8 inch or 1/4 inch. Check your manual or the stamp on your current chain to know which one your saw needs.
How to read gauge and what it controls
Gauge is the thickness of the drive links — the metal tabs that stick down from the chain and ride in the groove cut into your bar. Gauge is also stamped on the chain and is usually expressed in thousandths of an inch: .050 inch, .058 inch, and .063 inch are standard sizes. A thicker gauge means a stronger chain, but it also means more weight and more drag on the engine.
The bar has a groove milled into it to a specific width, and the drive links have to fit that groove snugly. If the gauge is too thin, the chain will rattle side to side and can derail. If the gauge is too thick, the chain will not fit into the groove at all. Like pitch, gauge is not adjustable — your bar is cut for one specific gauge, and that is the only one that will work.
Most bars are cut for .050 inch or .058 inch gauge. Some larger professional bars use .063 inch. Your manual will tell you which one your bar needs, or you can measure the groove width with a caliper if you have one.
Counting drive links and matching bar length
Drive link count is the total number of drive links on the entire chain. This number changes based on how long your bar is — a longer bar needs a longer chain with more drive links. A 16-inch bar might need 55 drive links, while a 20-inch bar might need 72. If you put a chain with too few drive links on a long bar, it will be too short and will not reach around the bar. Too many drive links and the chain will be too loose or will not fit at all.
To count drive links, lay the chain on a flat surface and count every metal tab that sticks down from the chain. Count all the way around until you reach the starting point. Write down the number. This is your drive link count.
You can also find the drive link count in your owner's manual, which is faster and more reliable than counting. The manual will list the correct chain size as something like "3/8 inch pitch, .050 inch gauge, 55 drive links" or similar. If you have lost your manual, the manufacturer's website usually has a PDF version you can read for free by model number.
Where to find the correct size in your manual or online
Your owner's manual has a section on replacement parts or maintenance that lists the exact chain size your saw needs. This section usually appears near the back of the manual and may be labeled "Replacement Parts," "Specifications," or "Maintenance Schedule." The chain size will be listed with all three measurements: pitch, gauge, and drive link count.
If you do not have the manual, you can find it online by searching the manufacturer's name and your saw's model number. Most manufacturers post manuals as free PDFs on their support pages. You can also call the manufacturer's customer service line with your model number, and they will tell you the correct chain size over the phone.
Some hardware stores and outdoor equipment shops will also look up the correct size for you if you bring in your saw or tell them the model number. This is a free service at most places, and it takes the guesswork out of ordering a replacement.
What happens when pitch or gauge does not match
Putting a chain with the wrong pitch on your saw will cause the sprocket to miss the drive links as the chain moves. You will hear a grinding or chattering sound, and the chain will not cut effectively. The engine may stall or rev without the chain moving. Over time, this will damage both the sprocket and the drive links on the chain.
Using the wrong gauge causes different problems. A gauge that is too thin will rattle in the bar groove and can jump off the bar during cutting, which is dangerous. A gauge that is too thick will not fit into the groove at all, or it will bind so tightly that the chain cannot move. Either way, you will not be able to start the saw or the chain will stall when ready.
The wrong drive link count means the chain is the wrong length for your bar. Too short and it will not reach all the way around. Too long and it will be loose, which causes derailing and poor cutting. Always verify all three numbers before you buy a replacement chain.
How to measure your bar if you need to replace it
If you are replacing both the bar and chain, you need to know your bar length. Measure from the tip of the bar to the point where it enters the saw body. This is your bar length. Most bars come in standard lengths: 12 inches, 14 inches, 16 inches, 18 inches, 20 inches, and larger. Your measurement should match one of these standard sizes.
Once you know your bar length, you can look up the correct chain size for that length in your manual. Different bar lengths on the same saw model may require different drive link counts, even though the pitch and gauge stay the same. For example, a 16-inch bar might need 55 drive links, but an 18-inch bar on the same saw model might need 62 drive links.
Frequently Asked Questions
Can I use a chain with a different pitch if the gauge matches?
No. Pitch and gauge are independent measurements, and both have to match your saw. A chain with the correct gauge but wrong pitch will not engage with your sprocket properly and will not cut. Always verify both pitch and gauge before buying a replacement.
What if I cannot find the stamp on my chain?
You can measure pitch by measuring the distance between three consecutive rivets and dividing by two. For gauge, measure the thickness of a drive link with a caliper or ruler. If you have neither tool, take your chain to a hardware store or equipment shop and ask them to measure it for you.
Does a longer chain always mean a longer bar?
Yes, but not all longer chains fit all saws. A longer chain needs more drive links, but it also has to have the same pitch and gauge as your saw. A chain that is too long for your bar will be loose and unsafe. Always match the drive link count to your bar length.
Can I adjust the chain tension to make a wrong-sized chain fit?
No. Chain tension adjustment only takes up slack in a chain that is the correct size. If the pitch or gauge is wrong, no amount of tension adjustment will make it work. If the drive link count is wrong, tension adjustment cannot change the chain length.
Where do I find the model number to look up my manual?
The model number is usually stamped on a label on the saw body, often near the handle or on the side of the engine housing. Take a photo of the label or write down the full model number, then search the manufacturer's website with that number to find your manual.