You can replace a Dodge Charger key fob battery yourself in about five minutes with a coin and a fresh battery
The battery in your Dodge Charger key fob will eventually die. When it does, you do not need to visit a dealer or buy a new fob — you just need to open the case, remove the old battery, and drop in a new one. The whole job takes longer to find a coin than to do the work.
Dodge Charger key fobs use a CR2032 battery, which you can find at any pharmacy, grocery store, hardware store, or online retailer for a few dollars. The fob itself snaps open with a flathead coin, and the battery sits in a plastic holder that you lift straight out.
Key Takeaways
- Dodge Charger key fobs use a CR2032 battery, the same size used in watches and calculators, available everywhere for under five dollars.
- You open the fob by inserting a coin into the slot on the edge and twisting gently until the two halves separate.
- The battery holder lifts straight out, and you swap the old battery for the new one by pressing it in until it clicks.
- After reassembly, test the fob buttons before you leave the store or your home to confirm the new battery works.
What battery your Dodge Charger key fob needs
All Dodge Charger key fobs from recent model years use a CR2032 coin cell battery. This is a standard battery size — 20 millimeters across and 3.2 millimeters thick — and it is the same battery used in watches, calculators, and many other small devices. You will find them in the battery aisle of any pharmacy, supermarket, or hardware store, usually in a pack of one or more.
The battery costs between two and five dollars depending on the brand and where you buy it. Name brands like Duracell and Energizer cost slightly more than store brands, but they all work the same way in a key fob. If you are already at a store for something else, pick one up while you are there so you have it when your fob dies.
How to open your Dodge Charger key fob
The two halves of your key fob are held together by a seam that runs around the edge. On one side of this seam, you will see a small slot — this is where you insert a coin to pry the fob open. A penny, dime, or quarter all work; a flathead screwdriver also works if you are careful not to damage the plastic.
Insert the coin into the slot and twist gently, as if you were opening a battery compartment on a toy or remote control. You are not forcing it — the fob is designed to come apart this way. After a quarter turn or so, you will feel the halves start to separate. Once they are loose enough, you can pull them apart by hand. Set the metal battery holder and circuit board aside on a clean surface where you will not lose them.
Removing the old battery and installing the new one
Inside the fob, the CR2032 battery sits in a plastic or metal holder. The battery is held in place by the shape of the holder itself — there are no screws or clips. To remove it, straightforward lift the battery straight up and out of the holder. If it is stuck, a gentle pry with your fingernail or the edge of a coin will free it.
Before you install the new battery, check which side is facing up. The CR2032 has a flat positive side (marked with a plus sign) and a domed negative side. The positive side should face up toward the circuit board. Drop the new battery into the holder and press down gently until you hear or feel a small click — that is the battery seating fully. Do not force it; if it does not click, flip it over and try again.
Putting the fob back together and testing it
Once the new battery is in place, line up the two halves of the fob so the seams match. Press them together firmly until they snap shut. You should hear a click or feel a slight resistance as the two halves lock. If they do not snap together, check that the battery holder is sitting flat and that nothing is blocking the seam.
Before you put the fob away, test it right away. Press each button — lock, unlock, panic, trunk, or whatever buttons your fob has — and confirm that your Charger responds. If nothing happens, open the fob again and check that the battery is seated correctly and facing the right direction. If the fob still does not work after you reseat the battery, the problem may be something other than the battery, and you should contact a Dodge dealer.
When to replace your key fob battery
Most CR2032 batteries last two to four years in a key fob, depending on how often you use it. You will notice the fob is dying when the buttons require a harder press, when you have to be closer to your car for it to work, or when some buttons stop working while others still do. These are all signs that the battery voltage is dropping.
If your fob stops working completely, do not assume the battery is dead — it could be a broken button, a damaged circuit board, or water damage. But a dead battery is the most common reason, and it is the cheapest and fastest thing to rule out. Replacing the battery costs a few dollars and takes five minutes, so it is always worth trying first.
Frequently Asked Questions
Can I use a different battery size if I cannot find a CR2032?
No. The CR2032 is the only battery that fits the holder in a Dodge Charger key fob, and using a different size will not work and may damage the fob. CR2032 batteries are extremely common and available at nearly every store that sells batteries, so finding one should not be difficult.
What if the fob still does not work after I replace the battery?
Open the fob again and confirm the battery is seated correctly with the positive side facing up. If it is, the problem may be a broken button contact, water damage inside the fob, or a dead circuit board. Contact a Dodge dealer for a replacement fob or repair options.
Is it safe to replace the battery myself, or should I go to a dealer?
Replacing the battery yourself is completely safe. There is no risk of electrical shock, and you cannot damage the fob by opening it — the seam is designed to come apart. A dealer will charge you thirty to fifty dollars for the same five-minute job, so doing it yourself saves money and time.
How do I know which side of the CR2032 battery goes up?
The flat side with a plus sign (+) is the positive terminal and should face up toward the circuit board. The domed side is negative. If you install it upside down, the fob will not work, but you can straightforward flip it over and try again — it will not hurt anything.
Can I buy a CR2032 battery online, or do I need to go to a store?
You can buy CR2032 batteries online from retailers like Amazon, or in person at pharmacies, supermarkets, hardware stores, and dollar stores. Online orders may take a few days to arrive, so if your fob is already dead and you need it working today, a local store is faster.