What you need to know before draining your radiator
The 2016 Subaru Outback uses a closed-loop cooling system that holds about 5.5 quarts of coolant. You can change the fluid yourself with basic tools, but the job requires the engine to be completely cold — waiting at least three hours after driving prevents burns from hot coolant under pressure. Subaru specifies using their OEM coolant or an equivalent long-life antifreeze; using the wrong type can damage the aluminum engine block and water pump.
The entire process takes between one and two hours, depending on how quickly the engine cools and how comfortable you are working underneath the vehicle. You'll need a drain pan, a socket set, a hose clamp tool or pliers, and fresh coolant mixed to the correct ratio with distilled water.
Key Takeaways
- The 2016 Outback holds 5.5 quarts of coolant and requires the engine to be stone cold before you open the system to avoid severe burns.
- Subaru specifies OEM coolant or equivalent long-life antifreeze; mixing brands or using standard green coolant can corrode the aluminum engine components.
- The drain plug is located on the bottom of the radiator, and you must also open the bleeder valve on the thermostat housing to release air pockets after refilling.
- After refilling, you need to run the engine and bleed air from the system multiple times, which is the most common step people skip and regret.
Locating the drain plug and preparing the workspace
Jack up the front of the vehicle on a level surface using jack stands — never rely on a jack alone. The drain plug sits on the driver's side of the radiator, at the lowest point. You'll see a plastic bolt roughly the size of a quarter head; this is what you're looking for. Place your drain pan directly underneath before loosening anything.
Before you touch the drain plug, locate the bleeder valve on the thermostat housing. On the 2016 Outback, this is a small bolt on top of the engine, toward the front. You won't open it yet, but knowing where it is saves time later. Also locate the radiator cap on top of the radiator — you'll need to remove this first to break the system's pressure seal.
Draining the old coolant safely
Remove the radiator cap by turning it counterclockwise. This step is critical because it allows air into the system and prevents a vacuum from forming as coolant drains. Without opening the cap, the coolant will drain very slowly or stop entirely.
Loosen the drain plug by turning it counterclockwise with a socket wrench. Once it's loose enough to turn by hand, unscrew it the rest of the way and set it aside in a safe place — it's straightforward to lose. Let the coolant drain completely into your pan. This can take 10 to 15 minutes. While it drains, inspect the plug for cracks or damage; if it's damaged, replace it with a new one before refilling.
Once the flow stops, wipe the drain plug and the threads around the opening with a clean rag. Reinstall the drain plug and tighten it firmly but not so hard that you crack the plastic radiator housing. Hand-tight plus a quarter turn with a wrench is usually correct.
Mixing and adding new coolant
Subaru recommends a 50/50 mix of coolant and distilled water. If you buy pre-mixed coolant, you can pour it straight in. If you buy concentrate, measure out the correct ratio in a separate container before adding it to the radiator. Using tap water instead of distilled water introduces minerals that can clog the cooling passages over time.
Pour the new coolant slowly into the radiator opening. Fill it until the level reaches the bottom of the filler neck — not all the way to the top. This leaves room for the coolant to expand as the engine warms. Replace the radiator cap by turning it clockwise until it seats firmly.
Bleeding air from the cooling system
This is the step that determines whether your coolant change actually works. Air pockets trapped in the system prevent proper circulation and cause overheating. Start the engine with the radiator cap on and let it idle for 30 seconds, then turn it off and wait for it to cool slightly. Open the bleeder valve on the thermostat housing by turning it counterclockwise with a wrench — coolant may drip out, so have your drain pan ready.
Tighten the bleeder valve once coolant flows steadily without air bubbles. Start the engine again and let it run until the temperature gauge reaches normal operating range. Turn the engine off and wait for it to cool. Repeat this cycle two more times: start, run until warm, shut off, cool down, and check the bleeder valve. Each time you open the bleeder, you're releasing trapped air that would otherwise cause problems.
After the third cycle, check the coolant level in the radiator. It may have dropped as air pockets collapsed. Top it off if needed, then replace the radiator cap. Check underneath the radiator and around the drain plug for leaks before driving.
Common mistakes and what goes wrong
The most frequent error is skipping the bleeding process or doing it only once. Many owners think filling the radiator is the whole job, then wonder why their temperature gauge climbs or they see warning lights after a few days of driving. Air in the system prevents coolant from reaching the top of the engine, causing localized overheating.
Another common problem is using the wrong coolant type. Subaru Outbacks from 2016 onward use long-life coolant that lasts longer and protects aluminum better than older green or orange coolants. Mixing types or using the wrong one can cause corrosion inside the engine block, which is expensive to repair.
Tightening the drain plug too hard can crack the plastic radiator housing, creating a leak that shows up days or weeks later. Hand-tight plus a quarter turn is sufficient; the plug doesn't need to be wrenched down.
When to change your coolant and disposal
Subaru recommends changing coolant every 30,000 miles or every two years, whichever comes first. If you drive in severe conditions — frequent towing, extreme heat, or stop-and-go traffic — change it sooner. Check your owner's manual for the specific interval for your driving patterns.
Old coolant is toxic and must be disposed of properly. Many auto parts stores and recycling centers accept used coolant for free. Never pour it down the drain or into the ground. If you're unsure where to take it, call your local waste management facility or check Earth911.com for nearby drop-off locations.
Frequently Asked Questions
Can I change the coolant without jacking up the car?
You can access the drain plug from above if you're flexible, but jacking the vehicle gives you better visibility and safer access. If you do work without jacking, use wheel chocks behind the rear wheels and never crawl under an unsupported vehicle.
What if coolant leaks from the drain plug after I reinstall it?
The plug may not be seated properly, or the threads may be damaged. Turn off the engine, let it cool, and tighten the plug another quarter turn. If it still leaks, remove the plug and inspect the threads. If they're stripped, you may need a slightly larger replacement plug or a threaded insert kit.
How do I know if there's still air in the system?
Air pockets usually show up as overheating, a rising temperature gauge, or a coolant warning light within the first few days of driving. If this happens, repeat the bleeding process: start the engine, let it warm, shut it off, cool it down, and open the bleeder valve again. You may need to do this three to five times total.
Can I use universal coolant instead of Subaru brand?
Yes, as long as it's a long-life, aluminum-safe coolant rated for your vehicle. Check the label to confirm it's compatible with 2016 Subaru models. Avoid old-style green or orange coolants, which are not compatible with the 2016 Outback's cooling system.
Do I need to burp the cooling system after changing the coolant?
Yes — "burping" is another term for bleeding air from the system. The bleeder valve on the thermostat housing is your burp valve. Opening it while the engine runs allows trapped air to escape. This is not optional; skipping it is the main reason coolant changes fail.