What chip and seal is and why roads get this treatment
Chip and seal is a thin layer of asphalt and gravel sprayed onto an existing road surface. It costs less than repaving and lasts 7 to 10 years, so state and local governments use it to extend the life of roads that aren't damaged enough to warrant full replacement. The process involves spraying a layer of liquid asphalt, then spreading small stone chips on top while the asphalt is still wet. A roller compacts everything together.
You'll see chip and seal most often on rural roads, county roads, and secondary highways. It's cheaper than hot-mix asphalt but rougher and less durable than a full repave. The surface is intentionally textured to improve tire grip, which is why it feels different from smooth asphalt.
Key Takeaways
- Chip and seal roads have a loose gravel surface that can cause your tires to lose traction, especially when braking or turning.
- Reduce your speed on chip and seal surfaces, increase your following distance, and avoid sudden braking or acceleration.
- Loose stones can damage your windshield and undercarriage, so drive cautiously and consider reporting severe damage to your insurance.
- Chip and seal typically lasts 7 to 10 years before the road needs maintenance or repaving.
How chip and seal affects your traction and braking
The loose gravel on a chip and seal surface reduces the contact between your tires and the road compared to smooth asphalt. This means your tires grip less effectively, especially in wet conditions or when you brake hard. Your stopping distance will be longer, and your vehicle may slide or skid if you brake suddenly.
Turning on chip and seal also carries more risk. The loose stones shift under the weight of your vehicle, which can cause your tires to slip sideways. This is particularly dangerous on curves or when changing lanes. All-wheel drive and good tire tread help, but they don't eliminate the risk.
Safe driving practices on chip and seal roads
Reduce your speed below the posted limit, especially if the road is wet or if you see loose gravel piled at the edges. A good rule is to drive 5 to 10 miles per hour slower than you normally would on asphalt. This gives your tires more time to grip and gives you more time to react if something goes wrong.
Increase your following distance to at least 8 to 10 seconds behind the vehicle ahead of you. On regular asphalt, 3 to 4 seconds is standard; chip and seal requires more. Avoid sudden braking, hard acceleration, and sharp turns. If you need to stop, brake gently and gradually rather than slamming the pedal.
If you see loose gravel in your lane, do not swerve suddenly. Swerving can cause you to lose control. Instead, ease off the gas, brake gently if needed, and maintain your lane. If the road is freshly sealed, the surface may still be soft—drive even more slowly and avoid stopping on the road itself if possible.
Windshield and vehicle damage from flying stones
Chip and seal roads throw loose stones into the air, especially when vehicles drive over them at speed. These stones can hit your windshield, windows, and the front of your vehicle, causing chips and cracks. Stones can also damage your undercarriage, suspension components, and paint.
There is no way to completely avoid this damage on chip and seal roads, but you can reduce the risk by maintaining distance from other vehicles. Vehicles ahead of you kick up more stones. If a stone hits your windshield, document the damage with photos and check your insurance policy. Some comprehensive coverage includes glass damage, though you may have a deductible. If the damage is severe, contact your insurance company to report it.
When chip and seal is newly applied
Freshly sealed roads are the most hazardous. The asphalt is still soft, and stones are not yet fully compacted. Avoid these roads if possible for the first week or two after sealing. If you must drive on one, go slowly and avoid stopping on the road itself—the weight of your vehicle can sink into the soft surface and create ruts.
You may see signs warning of fresh chip and seal. Heed them. The road will improve as traffic compacts the stones and the asphalt hardens, but during that initial period, traction is at its worst and stone damage is most likely.
Differences between chip and seal and other road surfaces
Chip and seal is rougher and less predictable than smooth asphalt but more durable than gravel roads. Unlike a full asphalt repave, chip and seal does not require removing the old surface, which is why it costs less and can be done quickly. However, it does not last as long as new asphalt and requires more maintenance.
Gravel roads have even less traction than chip and seal, but they are typically found in rural areas with lower traffic. Concrete roads are smoother and more durable than chip and seal but are more expensive to build. Chip and seal is a middle ground—cheaper than concrete or new asphalt, but more durable than gravel.
Reporting problems with chip and seal roads
If a chip and seal road is in poor condition—with large potholes, missing stones, or excessive loose gravel—you can report it to your local public works department or county road commission. Most have online forms or phone numbers for reporting road damage. Include the road name, location, and a description of the problem.
If your vehicle is damaged by road conditions, document the damage with photos and note the date, time, and location. Contact your insurance company to report it. You may also be able to file a claim with the government entity responsible for the road, though these claims are often difficult to pursue and may require proof that the road was negligently maintained.
Frequently Asked Questions
Can chip and seal damage my tires?
Chip and seal can puncture or cut tires if sharp stones are embedded in the surface, but this is less common than windshield damage. Inspect your tires regularly for cuts or bulges. If you get a flat, check whether it was caused by a road hazard—your insurance may cover it under comprehensive coverage depending on your policy.
Why do roads get chip and seal instead of being repaved?
Chip and seal costs significantly less than full repaving and extends a road's life by 7 to 10 years. Governments use it on roads that are not yet damaged enough to warrant the expense of repaving. Once a chip and seal road reaches the end of its life, it is typically repaved.
Is it safe to drive a motorcycle on chip and seal?
Motorcycles are at higher risk on chip and seal because they have less traction to begin with and are more sensitive to surface changes. If you ride a motorcycle, reduce speed significantly, avoid sudden braking or turning, and be especially cautious in wet conditions.
How long does it take for a chip and seal road to become safe?
A newly sealed road becomes safer as traffic compacts the stones and the asphalt hardens, typically within 1 to 2 weeks. However, the road will remain rougher and less predictable than smooth asphalt for its entire 7 to 10 year lifespan.
What should I do if I hydroplane on a chip and seal road?
If you hydroplane, remain calm and do not brake suddenly. Ease off the gas, keep the steering wheel straight, and let the vehicle slow naturally. Once you regain traction, drive slowly and carefully. Hydroplaning on chip and seal is more likely in heavy rain because the loose stones do not channel water away as effectively as smooth asphalt.