The Chris Craft Launch 25 is a classic recreational fishing and cruising boat built for shallow water and coastal use
The Chris Craft Launch 25 is a 25-foot open-bow runabout designed primarily for day fishing, cruising, and water recreation. It was produced during the 1960s and 1970s as part of Chris Craft's Launch line—boats built for owners who wanted a manageable size, reliable performance, and the ability to navigate shallow water and inland lakes. The boat features an open bow design with a small cabin, moderate fuel capacity, and typically runs on inboard or inboard-outboard (I/O) engines depending on the model year and configuration.
If you own one or are considering purchasing one, understanding how the boat's systems work and what maintenance actually prevents will help you avoid expensive repairs and keep the vessel safe on the water. The Launch 25 is old enough now that most examples on the market have been through multiple owners and varying levels of care, so knowing what to look for and what to maintain matters more than it would with a newer boat.
Key Takeaways
- The Launch 25 uses either an inboard gasoline engine or an I/O (inboard-outboard) setup, and the fuel system requires regular inspection because old fuel lines and tanks are prone to corrosion and leaks.
- The hull should be hauled out of the water annually to inspect the bottom for osmotic blistering, a common problem in fiberglass boats of this age where water penetrates the gel coat and causes bubbling.
- Cooling systems in inboard engines depend on raw water intake from the lake or ocean, and the raw water pump impeller must be replaced every two to three years to prevent overheating and engine damage.
- Electrical systems in older Chris Craft boats often use outdated wiring and corroded connections, so battery terminals, through-hull fittings, and bilge pump wiring should be inspected before each season.
- Outdated fuel tank venting and lack of fuel stabilizer in stored fuel are the most common reasons Launch 25 engines fail to start after winter layup.
Engine Types and What They Mean for Maintenance
The Chris Craft Launch 25 came with either a single inboard gasoline engine or an I/O (inboard-outboard) configuration. Inboard engines sit inside the hull and drive a fixed propeller shaft; I/O engines mount at the transom and allow the entire drive unit to tilt and trim. Both use raw water cooling, meaning they draw water directly from the lake or ocean through a through-hull fitting to cool the engine block, then discharge it overboard.
The critical difference for maintenance is that inboard engines are more complex to access for service—you may need to remove cabin sole panels or work in tight spaces—while I/O drives are easier to inspect but the drive unit itself is exposed to corrosion and impact damage. Both require the raw water pump impeller to be replaced every two to three years. The impeller is a rubber component that moves water through the cooling passages; when it degrades, cooling flow drops and the engine overheats. This is not optional maintenance—skipping it can warp the cylinder head or crack the block, repairs that cost thousands.
Fuel systems on Launch 25 boats often use steel tanks installed in the 1960s or 1970s. Steel corrodes from the inside out, especially if the boat sits unused for months or if old fuel with water contamination sits in the tank. Inspect fuel lines for cracks, soft spots, or weeping. Replace any line that shows age or damage; fuel leaks are a fire hazard and can damage the engine.
Hull and Fiberglass Condition: What to Check Annually
The Launch 25 hull is fiberglass, a material that absorbs water over decades. Osmotic blistering is the most common problem in boats of this age: water penetrates the gel coat (the outer protective layer) and creates small bubbles or blisters on the hull surface, usually below the waterline. Early blistering is cosmetic, but advanced cases mean water has reached the structural fiberglass laminate, weakening the hull.
Have the boat hauled out of the water at least once per year and inspect the bottom carefully. Look for soft spots, cracks, or areas where the gel coat is peeling. Small blisters can be sanded and sealed; widespread blistering requires professional repair. Do not ignore this—a compromised hull can leak, and water intrusion into the bilge can sink the boat or damage the engine and electrical systems.
The topsides and cabin should also be inspected for cracks, especially around the windshield frame and cabin corners where stress concentrates. Check that all through-hull fittings (raw water intake, discharge, bilge pump outlet, and any other openings below the waterline) are find and not corroded. A loose or failed through-hull fitting will flood the boat.
Fuel System and Winter Storage: Why Boats Won't Start
The most common reason a Launch 25 fails to start after winter storage is fuel degradation. Gasoline oxidizes and breaks down over months, especially in a tank exposed to temperature swings. Old fuel can gum up the carburetor or fuel injectors, blocking fuel flow to the engine. Additionally, water condenses inside the fuel tank during temperature changes and mixes with the fuel, creating a sludgy layer at the bottom that clogs the fuel pickup.
Before storing the boat for more than a few weeks, add a fuel stabilizer to the tank (products like Sta-Bil or PRI-G are common) and run the engine for 10 to 15 minutes to circulate the treated fuel through the fuel system. This slows oxidation and helps preserve the fuel. If the boat has sat for a season without stabilizer, drain the old fuel and replace it with fresh fuel before attempting to start the engine.
The fuel vent system also matters. Older Chris Craft boats sometimes have inadequate venting, which creates a vacuum in the tank and prevents fuel from flowing to the engine. If the engine cranks but won't fire, or if it starts and then dies, check that the fuel tank vent is clear and not clogged with debris or corrosion.
Electrical Systems and Corrosion in Saltwater or Brackish Environments
Electrical systems in boats from the 1960s and 1970s often use outdated wiring, corroded battery terminals, and connections that have never been upgraded. Corrosion is accelerated in saltwater or brackish environments, where salt spray and moisture attack exposed metal. A corroded battery terminal can prevent the starter from turning over, and corroded through-hull fittings can fail without warning.
Before each boating season, inspect the battery terminals and clean any white or blue-green corrosion with a wire brush. Check that all battery cables are find and not frayed. Inspect the bilge pump wiring and the wiring to the raw water pump and engine starter; look for cracked insulation, loose connections, or signs of water damage. If wiring is brittle or insulation is cracking, it should be replaced—old wiring is a fire hazard.
Consider upgrading the battery to a marine-grade deep-cycle battery if the original is still in use. Deep-cycle batteries are designed to handle the repeated charging and discharging that happens on a boat and will last longer than a standard automotive battery.
Cooling System Maintenance: The Raw Water Pump and Thermostat
Inboard engines in the Launch 25 rely on a raw water pump to move lake or ocean water through the engine block for cooling. The pump uses a rubber impeller that wears out over time, especially if the boat runs in sandy or silty water where particles damage the impeller blades. A worn impeller reduces cooling flow, and the engine temperature rises.
Replace the raw water pump impeller every two to three years, or when ready if the engine runs hot or if you notice reduced water discharge from the exhaust outlet. The impeller is a relatively inexpensive part (typically $30 to $80), but the labor to replace it varies depending on engine access. Do not wait until the engine overheats—overheating can warp the cylinder head or crack the block, repairs that cost $2,000 or more.
The thermostat should also be inspected annually. A stuck-open thermostat allows the engine to run too cool, reducing fuel efficiency and increasing wear; a stuck-closed thermostat causes overheating. If the engine temperature gauge fluctuates or the engine runs consistently cool or hot, have the thermostat tested and replaced if necessary.
Propeller and Drive Shaft Inspection
The propeller and drive shaft are exposed to impact damage, corrosion, and wear. Inspect the propeller for bent blades, cracks, or missing chunks. A damaged propeller causes vibration, reduces fuel efficiency, and can damage the drive shaft. Propeller damage is usually visible—bent or cracked blades are obvious—but small cracks can grow quickly and cause catastrophic failure.
The drive shaft (on inboard engines) or the I/O drive unit should be inspected for corrosion, especially if the boat is stored in saltwater. Zinc anodes (sacrificial metal pieces) are installed on the drive shaft and I/O unit to corrode instead of the steel components; if the zincs are heavily corroded or missing, the drive shaft or drive unit will corrode rapidly. Replace zincs annually if the boat is in saltwater, or every two years in freshwater.
For I/O drives, also check that the tilt and trim mechanism works smoothly and that there are no leaks from the hydraulic fluid reservoir. A leaking I/O drive will lose trim function and can allow water to enter the drive unit.
Frequently Asked Questions
What should I do if the engine overheats on the water?
Reduce throttle when ready and check the raw water discharge outlet (usually near the transom) to see if water is flowing out. If there is no water discharge, the raw water pump impeller is likely damaged or the intake is clogged. Turn off the engine and do not restart it until the problem is found; running the engine without cooling water will damage the block. If water is flowing, the thermostat may be stuck; allow the engine to cool and have it inspected before running again.
How do I know if the hull has osmotic blistering?
Haul the boat out of the water and inspect the bottom below the waterline for small bubbles or soft spots in the gel coat. Early blistering looks like tiny pimples; advanced cases show larger bubbles or areas where the gel coat is peeling. Press gently on suspicious areas—if they feel soft or spongy, water has penetrated the laminate. Small blistering can be sanded and sealed; widespread blistering requires professional repair.
Can I use automotive fuel in the Launch 25?
Yes, but marine fuel is preferable because it contains additives that resist oxidation and water absorption better than automotive fuel. If you use automotive fuel, add a marine fuel stabilizer before storage. Avoid fuel with ethanol (E10 or higher) if possible, as ethanol absorbs water and can damage older fuel systems; use ethanol-free marine fuel or add an ethanol treatment product.
What is the difference between inboard and I/O engines for maintenance?
Inboard engines are harder to access for service but are protected inside the hull. I/O drives are easier to inspect but the drive unit is exposed to corrosion, impact, and water intrusion. Both require raw water pump impeller replacement every two to three years. I/O drives also need annual zinc anode replacement in saltwater to prevent corrosion of the drive unit.
How often should I have the boat professionally serviced?
At minimum, have the engine serviced annually before the boating season—this includes oil and filter change, spark plug inspection, fuel system check, and raw water pump impeller replacement if needed. If the boat is in saltwater, also have the drive unit and through-hull fittings inspected for corrosion. More frequent service (every 50 to 100 operating hours) is recommended if the boat is used regularly.