What the Chris Craft Launch 27 is and what owners should know

The Chris Craft Launch 27 is a cabin cruiser built by Chris Craft Industries, a boat manufacturer based in Pompano Beach, Florida. The boat is roughly 27 feet long and designed for recreational cruising, with sleeping quarters, a galley, and a head (bathroom). Most Launch 27 models were produced in the 1980s and 1990s, though the company has built boats under the Chris Craft name since the 1920s. If you own one or are thinking about buying one, you are dealing with an older vessel that requires regular maintenance to stay safe and functional.

The Launch 27 is a fiberglass hull boat with inboard engines, typically powered by either gasoline or diesel motors depending on the year and model. Because these boats are now 30 to 40 years old, most of the work you will do involves keeping systems that were installed decades ago running reliably. The good news is that parts, repair manuals, and experienced technicians are still available. The challenge is that older boats develop problems faster than newer ones, and some systems may need replacement rather than repair.

Key Takeaways

  • The Chris Craft Launch 27 is an older cabin cruiser that requires regular engine maintenance, including oil changes, fuel filter replacement, and winterization if you live in a cold climate.
  • The hull, deck, and cabin are made of fiberglass and need periodic inspection for cracks, soft spots, and water intrusion, which can lead to rot in the wooden core.
  • Electrical systems, plumbing, and through-hull fittings are common problem areas on boats this age and should be checked before each season.
  • You can find repair information through Chris Craft owner forums, marine mechanics who work on older boats, and original owner's manuals if available.
  • Hauling the boat out of the water annually for inspection and bottom painting is standard practice and costs vary by location and boat size.

Engine and fuel system maintenance

The engine is the most expensive system on your Launch 27, and keeping it running well starts with regular oil and filter changes. How often depends on whether you have a gasoline or diesel engine and how much you use the boat. Gasoline engines typically need an oil change every 50 to 100 hours of operation, while diesel engines can often go longer. Check your owner's manual or ask a marine mechanic familiar with your specific model year to confirm the interval.

Fuel system problems are common on older boats because gasoline and diesel both break down over time, especially if the boat sits unused for months. Water can also accumulate in fuel tanks, leading to corrosion and clogged fuel filters. Before each boating season, have the fuel filter inspected and replaced if it looks dirty or discolored. If the boat has been sitting for more than a few months, consider having the fuel tank pumped and inspected by a professional. Diesel engines are generally more forgiving of old fuel than gasoline engines, but both benefit from fresh fuel and clean filters.

Winterization is essential if you keep the boat in a region where water freezes. This process involves draining the cooling system, adding antifreeze to the engine block and raw water lines, and stabilizing the fuel. Skipping winterization can result in cracked engine blocks and frozen water lines, repairs that cost far more than winterization itself. If you are new to boat ownership, have a marine mechanic handle winterization the first time so you understand what is involved.

Hull, deck, and cabin inspection

Fiberglass hulls can last decades, but they are not immune to damage. Cracks, gouges, and soft spots in the hull allow water to seep into the core, which is often made of wood or balsa. Once water gets in, rot can spread quickly and become expensive to repair. Inspect the hull regularly, especially the bottom and the area where the hull meets the keel. Look for discoloration, soft areas when you press on them, or visible cracks. Small cracks can be sealed with marine epoxy, but large areas of soft hull material may require professional repair or replacement.

The deck and cabin are also fiberglass and face similar risks. Water pooling on the deck can eventually find its way through seams and into the cabin. Check all deck seams, around the cabin windows, and where railings and hardware are bolted through the deck. These are common entry points for water. Caulking and sealant degrade over time and need to be replaced every few years. If you see water stains on the cabin ceiling or walls, or if the cabin smells musty, there is likely water intrusion somewhere. Tracking down the source can be time-consuming, but ignoring it will make the problem worse.

The cabin interior includes wood trim, cabinetry, and upholstery that can rot or mildew if exposed to moisture. Keep the cabin well-ventilated when the boat is not in use, and run a dehumidifier or open the hatches on dry days. If you spot soft wood or dark stains that smell like mold, address them quickly. Mold can spread to other parts of the boat and poses health risks if you spend time in the cabin.

Electrical and plumbing systems

The electrical system on a Launch 27 typically includes a battery bank, a battery charger, and a generator if the boat has one. Batteries lose capacity over time and should be tested annually. Corroded battery terminals and loose connections are common causes of starting problems. Check the battery cables for corrosion and clean them if needed. If the boat has been sitting unused, the battery may be fully discharged and will need to be recharged slowly before the engine will start.

The wiring throughout the boat can deteriorate, especially in damp areas like the engine room and bilge. Corroded or damaged wiring can cause electrical fires, so inspect visible wiring for cracks in the insulation or green corrosion on the connectors. If you are not comfortable working with electrical systems, have a marine electrician check the boat before you take it out on the water. The same applies to the generator if the boat has one; generators require regular maintenance and professional service if they fail to start or run.

The plumbing system includes the freshwater tank, the galley sink, the head, and the waste tank. Hoses can crack or become brittle with age, and connections can loosen. Check all visible hoses for cracks or soft spots, and tighten any loose fittings. If the boat has been sitting for a long time, the freshwater tank may be contaminated or empty. Drain and rinse the tank before refilling it. The waste tank should be pumped out at a marine pump-out station, never overboard. If the head is not working, the problem is often a clogged or frozen line, which a marine plumber can clear.

Through-hull fittings and seacocks

Through-hull fittings are openings in the hull where pipes pass through to bring in seawater for cooling or to discharge wastewater. Each fitting has a seacock (a valve) that can be closed to prevent water from entering the boat if the fitting fails. These are critical safety devices. Before each boating season, locate all seacocks and make sure they open and close smoothly. If a seacock is stuck or corroded, have it replaced. A stuck seacock that you cannot open in an emergency could lead to the boat sinking.

The through-hull fittings themselves can corrode or crack, especially if they are made of bronze or other metals that react with saltwater. Inspect them for leaks or white crusty corrosion. If you see water dripping from a fitting, tighten the connection first. If tightening does not stop the leak, the fitting may need to be replaced. This is a job for a marine mechanic, as it involves working below the waterline and requires the boat to be hauled out or the area to be sealed off while the repair is made.

Hauling and bottom maintenance

Hauling the boat out of the water once a year is standard practice for boats that spend most of their time in the water. During a haul-out, the bottom is inspected for damage, cleaned, and repainted with antifouling paint to prevent marine growth. The cost varies depending on the size of the boat and the location of the marina, but expect to pay several hundred to over a thousand dollars for a Launch 27. Some marinas offer winter storage with haul-out included, which can be more economical than paying for haul-out separately.

While the boat is out of the water, it is a good time to inspect the keel, the rudder, and the propeller. The keel can develop cracks or separation from the hull, and the rudder can become loose or damaged. The propeller should be checked for bent blades or corrosion. If you spot any damage, have it repaired while the boat is already out of the water. Putting the boat back in the water with known damage will only make the problem worse.

Finding repair information and may have access to mechanics

Chris Craft owner forums and online communities are good places to ask questions about specific maintenance tasks and to find recommendations for mechanics. The Chris Craft Antique Boat Club maintains a directory of members and resources. If you have the original owner's manual, it will have maintenance schedules and specifications for your model year. Many manuals are also available online through boat forums or marine document archives.

When looking for a mechanic, ask whether they have experience with Chris Craft boats and with the specific engine in your boat. A mechanic who works on modern boats may not be familiar with systems that are 30 or 40 years old. Get estimates in writing before authorizing work, and ask for an explanation of what is being done and why. If a mechanic recommends a major repair, it is reasonable to get a second opinion before proceeding.

Frequently Asked Questions

How much does it cost to maintain a Chris Craft Launch 27 per year?

Costs vary widely depending on how much you use the boat, where you keep it, and what repairs are needed. Routine maintenance like oil changes, filter replacements, and haul-out typically runs $1,500 to $3,000 annually. Unexpected repairs can add significantly to that. Keeping money set aside for repairs is wise, as older boats often need work you did not anticipate.

Can I do my own maintenance on a Launch 27?

straightforward tasks like oil changes, filter replacements, and visual inspections are manageable for owners with basic mechanical skills. More complex work like engine repair, electrical troubleshooting, and hull repairs should be left to professionals. If you are unsure whether a task is within your ability, ask a marine mechanic before attempting it.

What should I do if I find water in the bilge?

Small amounts of water in the bilge are normal, but if water is accumulating faster than the bilge pump can remove it, there is a leak somewhere. Turn on the bilge pump and watch to see if the water level drops. If it does not, turn off the engine and look for the source of the leak. Check all through-hull fittings, hoses, and seams. If you cannot find the leak, have a marine mechanic inspect the boat.

Do I need to winterize if I keep my boat in a warm climate?

If the water temperature never drops below freezing, you do not need to winterize the cooling system. However, you should still stabilize the fuel and change the oil before storing the boat for an extended period. Warm climates can accelerate fuel breakdown and engine corrosion, so regular maintenance is still important.

Where can I find parts for a Chris Craft Launch 27?

Marine suppliers that stock parts for older boats, online retailers specializing in vintage boat parts, and salvage yards that dismantle old boats are all sources. Chris Craft owner forums often have members who know where to find specific parts. For engine and mechanical parts, contact dealers who service the engine brand in your boat.