What you need to know before you start

Clear tail lights on an R34 Skyline require you to remove the entire tail light assembly from the rear quarter panel, not just swap a bulb. The R34 uses a bolted-on housing that sits behind the bumper, and you'll need to access it from inside the trunk. Most owner replacements take 30 to 45 minutes per side once you have the parts in hand.

The R34 came with red tail lights from the factory. Clear housings are an aftermarket modification, so you're choosing between OEM red units (which bolt straight in) or reproduction clear housings that require the same mounting points. Either way, the removal and installation process is identical — the difference is what you're putting back.

Key Takeaways

  • R34 tail light housings bolt on from inside the trunk, not from outside the car, so you must open the trunk and remove interior trim to access them.
  • You will need a socket set (10mm and 12mm sockets are standard), a trim removal tool to avoid cracking plastic panels, and a helper to hold the housing while you work.
  • Clear aftermarket housings fit the same bolt pattern as OEM red lights, but wiring connectors are identical so no rewiring is needed.
  • The most common mistake is forcing the housing out without removing all bolts first, which cracks the quarter panel or the housing itself.

Tools and parts you'll need

Gather a socket set with 10mm and 12mm sockets, a ratchet, and a trim removal tool or flat-head screwdriver wrapped in tape to pry without scratching. You'll also want a flashlight or headlamp because the trunk area is dark, and a helper makes the job much easier since the housing is awkward to hold while you're unbolting it.

For the tail light itself, you have two main options: OEM Nissan red housings (which are harder to find and more expensive) or reproduction clear housings from aftermarket suppliers. Both use the same bolt pattern and electrical connectors, so either will bolt straight in. Clear housings typically cost between $80 and $150 per side depending on the supplier and whether they include bulbs.

Step-by-step removal process

Open the trunk and look at the inside of the rear quarter panel where the tail light sits. You'll see a rubber seal or trim panel covering the bolts. Use your trim tool to gently pry this away — don't force it or you'll crack the plastic. Once exposed, you'll see three or four bolts holding the housing to the car.

Unbolt all fasteners before you try to move the housing. Use your 10mm or 12mm socket (check your specific model year, as some R34s use different sizes) and remove each bolt completely. Once all bolts are out, gently pull the housing toward the inside of the trunk. It will come out at an angle. Disconnect the wiring harness by pressing the clip on the connector and pulling straight back — don't twist or yank.

Set the old housing aside and inspect the mounting area for cracks or damage. If the rubber seal tore, you can reuse it if it's still pliable, or replace it with a new gasket seal to prevent water from entering the trunk.

Installing the new clear tail light

Before you bolt the new housing in, connect the wiring harness first while the housing is still outside the car. Push the connector in until you hear a click. This prevents you from having to reach awkwardly into the tight space later. Check that the connector is fully seated by gently tugging on it — it should not come loose.

Slide the new housing into the mounting area at the same angle you removed the old one. Align the bolt holes with the studs on the car. Insert all bolts by hand first to make sure they thread correctly, then tighten them in a cross pattern (top-left, bottom-right, top-right, bottom-left) to avoid warping the housing. Tighten firmly but do not over-torque — these are plastic housings and the bolts will strip if you force them.

Once all bolts are tight, press the rubber seal or trim panel back into place. Close the trunk and test your lights. Turn on the ignition and have your helper stand behind the car to confirm both brake lights and reverse lights work. If one side is dim or out, check that the connector is fully seated.

Common problems and how to avoid them

The most frequent issue is cracking the housing or the car's quarter panel by pulling too hard before all bolts are removed. Take your time and verify every bolt is out before you explore any force. If you feel resistance, stop and look for a bolt you missed.

Water leaking into the trunk after installation usually means the rubber seal wasn't seated properly or was damaged during removal. If you see water pooling, remove the housing again, inspect the seal, and replace it if it's cracked or hardened. A new gasket seal costs $10 to $20 and takes five minutes to install.

Bulbs burning out quickly in clear housings is not a defect — it's normal. Clear housings reflect more light back at the filament, which generates extra heat and shortens bulb life. Some owners switch to LED bulbs to reduce heat and extend lifespan, though this requires checking your specific housing's compatibility first.

When to seek professional help

If you crack the quarter panel during removal, stop and take the car to a body shop. Attempting to repair it yourself will likely make it worse. If the wiring connector is damaged or corroded, you may need an electrician to repair or replace the harness — this is beyond a basic maintenance job.

If your clear housings are leaking water inside after installation, a shop can remove them, replace the seal, and reinstall them correctly. This usually costs $100 to $200 per side in labor, which is worth it to prevent rust damage to the trunk interior.

Frequently Asked Questions

Do I need to remove the bumper to access the tail lights?

No. The R34 tail light housings are accessed entirely from inside the trunk. You do not need to remove the bumper, though you will need to peel back the interior trim panel to reach the bolts.

Can I replace just the lens or do I have to replace the whole housing?

On the R34, the lens and housing are one piece. You cannot separate them, so if the lens is cracked or fogged, you must replace the entire assembly. This is why clear housings are sold as complete units, not individual lenses.

Will clear tail lights pass inspection?

This depends on your state or country. Some jurisdictions require red tail lights for safety and will not pass a vehicle with clear housings. Check your local vehicle code before purchasing clear lights, or confirm with your inspection station whether they allow them.

How do I know which bolts to remove if I can't see them clearly?

Use a flashlight or headlamp to illuminate the area. Once you peel back the rubber seal, the bolt heads are visible. If you're still unsure, take a photo with your phone's flash before you start — the image will show you exactly where each bolt is located.

What size are the tail light bulbs in an R34?

The R34 uses 1156 bulbs for the reverse light and 1157 bulbs for the brake and running lights. Check your specific housing's documentation, as some aftermarket clear housings may use different bulb types. Most suppliers include this information in the product listing.