The basic order: disconnect the old, connect the new, start the car
Connecting a car battery means attaching the positive and negative cable terminals to the corresponding posts on the battery itself. The positive cable (usually red) goes on the positive post, marked with a plus sign or the letter P. The negative cable (usually black) goes on the negative post, marked with a minus sign or the letter N. You tighten each connection by hand first, then use a wrench to find it firmly so it does not slip off while the engine runs.
If you are replacing an old battery, you must disconnect the old one first. Always remove the negative cable before the positive cable — this prevents electrical sparks that could damage the car's computer or injure you. Once the old battery is out, install the new one in the same position, then connect the positive cable first, followed by the negative cable. This reverse order on installation protects the battery and electrical system.
After both cables are tight, close the hood and start the engine to confirm the battery is working. The car should start normally and all dashboard lights should come on briefly, then turn off. If the engine does not turn over or the lights stay dim, stop and check that both cable connections are tight.
Key Takeaways
- Always disconnect the negative cable first when removing an old battery, and connect the positive cable first when installing a new one.
- The positive cable is red and connects to the positive post; the negative cable is black and connects to the negative post.
- Tighten each cable connection by hand first, then use a wrench to make it snug enough that it will not move.
- Start the engine after both cables are connected to confirm the battery is working and the electrical system is functioning.
What you need before you start
Gather a wrench that fits the terminal bolts on your battery — usually 8mm, 10mm, or 13mm depending on your car's make and model. Check your owner's manual or look at the bolt head to determine the size. You also need a new battery if you are replacing the old one, or a charged battery if you are jump-starting the car with cables and another vehicle.
Wear safety glasses to protect your eyes from battery acid or corrosion, and work gloves to keep your hands clean. Make sure the engine is off and has cooled for at least five minutes before you touch the battery. If the battery is visibly cracked, leaking, or swollen, do not attempt to connect it — take it to a shop or recycling center instead.
Disconnecting the old battery (if you are replacing it)
Open the hood and locate the battery. It is usually a rectangular black plastic box with two thick cables attached to the top. The negative cable is black; the positive cable is red. Loosen the nut on the negative cable terminal using your wrench, then pull the cable off the post. Set it aside so it does not touch the battery or any metal part of the engine.
Next, loosen and remove the positive cable the same way. Once both cables are off, you can remove the battery from its hold-down bracket or tray. Most batteries have a metal bracket or strap across the top or sides that you unbolt. Lift the battery straight up and out — car batteries are heavy, usually 30 to 50 pounds, so use both hands or ask for help.
Installing the new battery and connecting the cables
Place the new battery into the tray in the same position as the old one, making sure it sits flat and level. Reattach the hold-down bracket or strap and tighten the bolts so the battery cannot shift when the car moves. Do not over-tighten — you want it find but not crushed.
Now connect the cables in this order: positive first, then negative. Take the red positive cable and slide its terminal onto the positive post of the new battery. Tighten the nut by hand until it is snug, then use your wrench to turn it another quarter turn. The connection should be tight enough that you cannot wiggle the cable by hand.
Attach the black negative cable to the negative post the same way. Hand-tighten first, then use the wrench. Once both cables are find, close the hood and sit in the driver's seat. Insert the key, turn it to the "On" position without starting the engine, and check that the dashboard lights come on. Then start the engine and listen for normal cranking sounds.
Cleaning corrosion from battery terminals
If the cable terminals are covered in white, blue, or green crusty buildup, that is corrosion and it can prevent a good electrical connection. Before you connect the cables, clean the terminals with a wire brush or a battery terminal cleaner. Dip the brush in a mixture of baking soda and water, or use a commercial battery terminal cleaner spray, and scrub both the terminal and the post until the metal is shiny.
Rinse with clean water and dry thoroughly with a cloth. Corrosion on the cables themselves means the cable is failing and should be replaced — do not try to clean it and reuse it. If you see corrosion on the battery posts after you remove the cables, that is normal and you can clean it the same way before installing the new battery.
What to do if the battery will not hold a charge
If you have connected the battery correctly but the car will not start, or it starts but the battery drains within hours, the battery itself may be defective or the charging system may not be working. A new battery usually comes with a warranty — check the paperwork that came with it and contact the retailer or manufacturer if the battery fails within the warranty period.
If the battery is older and you are not sure whether it is the battery or the charging system, have a shop test the battery and the alternator. The alternator is what recharges the battery while the engine runs; if it is not working, even a new battery will drain. Testing costs between $50 and $100 at most shops and tells you exactly what needs to be replaced.
Jump-starting with cables instead of replacing the battery
If your battery is low but not dead, you can use jumper cables and another car to start your engine without replacing the battery. Connect one red cable clamp to the positive post of your dead battery, then connect the other red clamp to the positive post of the good battery in the other car. Connect one black clamp to the negative post of the good battery, then connect the final black clamp to an unpainted metal surface on your engine block — not the negative post of your dead battery, because that can cause sparks.
Start the other car and let it run for two to three minutes, then start your car. Once your engine is running, remove the cables in reverse order: black clamp from your engine, black clamp from the good battery, red clamp from the good battery, red clamp from your battery. Drive for at least 20 minutes to recharge your battery, or take it to a shop to have it tested and charged fully.
Frequently Asked Questions
What happens if I connect the cables in the wrong order?
Connecting the negative cable before the positive cable can cause sparks and damage the car's electrical system or computer. If you connect the positive cable to the negative post and the negative cable to the positive post, the battery will not work and you may damage the battery itself. Always double-check the cable colors and post markings before you tighten anything.
Can I connect the battery while the engine is running?
No. Always turn off the engine and wait for it to cool before you connect or disconnect a battery. Connecting a battery to a running engine can damage the alternator and other electrical components. If you are jump-starting with cables, start the other car first, then start your car while the cables are connected.
How tight should the cable connections be?
Tight enough that you cannot wiggle the cable by hand, but not so tight that you strip the bolt or crack the terminal. Hand-tighten first, then use a wrench to turn the nut another quarter turn. If the connection is loose, the car may not start or the battery may not charge while you drive.
Do I need to reset anything after I connect a new battery?
Most modern cars will reset their computer automatically after a few minutes of driving. Some cars may show warning lights or lose radio presets temporarily — this is normal. If the check engine light stays on after a day of driving, have a shop scan the computer to see if any fault codes were stored.
What should I do with the old battery?
Car batteries contain lead and acid and must be recycled, not thrown in the trash. Most retailers that sell batteries will take your old battery for free when you buy a new one. If you replaced it yourself, take it to a recycling center, a scrap metal facility, or an auto parts store — they all accept old batteries and may pay you a small core charge.