Converting an electric golf cart to gas is possible but requires replacing the entire drivetrain, not just swapping one fuel source for another

An electric golf cart runs on a battery pack and electric motor. A gas golf cart runs on an internal combustion engine, fuel tank, and carburetor or fuel injection system. These are fundamentally different powerplants. You cannot straightforward add a gas engine to an electric cart's frame—you must remove the battery, motor, and controller, then install a complete gas engine assembly with its own fuel system, exhaust, and cooling.

The conversion is technically feasible but expensive, time-consuming, and often impractical compared to buying a used gas cart outright. Most people who consider this conversion are trying to solve a problem—usually battery replacement cost or range anxiety—but the conversion itself creates new problems: loss of the cart's original engineering, potential safety issues, and ongoing maintenance of an older engine design.

Key Takeaways

  • A gas conversion requires removing the battery pack, electric motor, and controller entirely and installing a complete gas engine with fuel tank, carburetor or fuel injection, and exhaust system.
  • The total cost of parts, labor, and fabrication typically ranges from $3,000 to $8,000 or more, depending on engine choice and whether you do the work yourself.
  • You will lose the cart's original weight distribution, handling, and safety characteristics because the engine, fuel tank, and exhaust are mounted differently than the battery pack was.
  • A used gas golf cart in working condition usually costs less than a full conversion and comes with an engine already tuned to the cart's frame and suspension.
  • Converting an electric cart to gas may affect its resale value, insurance coverage, and local regulations depending on where you use it.

What you actually have to remove and install

Start with what comes out: the battery pack (usually eight to fourteen 6-volt or 8-volt batteries weighing 50 to 100 pounds each), the electric motor (typically 4 to 8 kilowatts), the motor controller (the electronic box that manages power delivery), the charging port, and all wiring between these components. On most carts, these parts occupy the underseat storage area and the rear cargo bed.

What goes in: a small gasoline engine (usually 5 to 13 horsepower, similar to a lawn mower or pressure washer engine), a fuel tank (typically 3 to 5 gallons), a carburetor or fuel injection system, an exhaust pipe and muffler, an air filter, an oil pan, and a cooling system if the engine requires it. You also need a clutch or belt drive to connect the engine to the cart's existing transmission, or you must replace the transmission entirely.

The engine must be mounted securely to the frame, which usually means welding or bolting a custom engine mount. The fuel tank must be positioned so it does not interfere with the steering, suspension, or cargo area. The exhaust must route safely away from passengers. None of this is plug-and-play.

Cost breakdown and what affects the price

A complete gas engine kit designed for golf cart conversion costs between $1,500 and $4,000, depending on engine size and whether it includes the fuel system and mounting hardware. Popular options include Predator, Lifan, and Honda small engines, though not all are sold as complete kits—you may need to source the carburetor, fuel tank, and mounts separately.

Labor costs vary widely. If you have welding skills and mechanical experience, you might complete the work yourself over several weekends. If you hire a shop, expect $1,500 to $3,000 in labor, depending on how much custom fabrication is needed. Some shops charge hourly rates ($75 to $150 per hour) and cannot predict the total time until they begin.

Additional expenses include exhaust piping, fuel line and fittings, an oil change kit, spark plugs, air filters, and any frame reinforcement needed to handle the engine's vibration. If the cart's transmission is weak or the clutch is worn, you may need to replace those too. A realistic total for a complete conversion is $3,000 to $8,000, and custom or high-performance conversions can exceed $10,000.

Why the conversion changes how the cart handles and feels

An electric cart's weight is distributed low and centered—the battery pack sits under the seat and in the cargo bed, keeping the center of gravity stable. A gas engine is heavier, sits higher, and is mounted forward or to one side, shifting the weight distribution. This changes how the cart corners, accelerates, and brakes. The suspension and steering geometry were engineered for the original weight and balance, so the converted cart may feel loose, nose-heavy, or unstable on slopes.

Vibration is another issue. Electric motors are smooth and nearly silent. Gas engines vibrate, especially small ones running at high RPM. The frame, steering wheel, and seat transmit this vibration directly to the driver and passengers. Over time, vibration can loosen bolts, crack welds, and wear out bearings faster than they would on a purpose-built gas cart.

Braking performance may suffer. Electric carts use regenerative braking (the motor slows the cart as it charges the battery) plus mechanical brakes. A converted cart loses regenerative braking and relies entirely on the original mechanical brakes, which were sized for a lighter vehicle. You may need to upgrade the brake system, which adds cost and complexity.

Fuel efficiency, maintenance, and long-term operating costs

A gas golf cart engine typically gets 8 to 15 miles per gallon, depending on engine size, load, and driving conditions. A small 5-horsepower engine uses less fuel than a 13-horsepower engine, but also has less power and slower acceleration. At current gas prices, fuel costs roughly $0.30 to $0.50 per mile. An electric cart costs roughly $0.05 to $0.10 per mile to charge, assuming residential electricity rates.

Gas engines require regular maintenance: oil changes every 50 to 100 hours of operation, air filter replacement, spark plug replacement, carburetor cleaning, and seasonal fuel system maintenance. If the engine sits unused for months, the fuel can gum up the carburetor, requiring professional cleaning. Electric carts need battery watering (if lead-acid) or battery replacement every 4 to 6 years, but no oil changes, spark plugs, or fuel system work.

Over five years, a converted cart may cost more to maintain and operate than an electric cart, especially if the engine requires repairs. Small gas engines are reliable but not designed for the duty cycle of a golf cart—they are meant for intermittent use on lawn mowers and generators. Running one continuously in a cart can shorten its lifespan.

Why buying a used gas cart is usually the better choice

A used gas golf cart in working condition typically costs $2,000 to $5,000, depending on age, brand, and condition. That is often less than the cost of converting an electric cart, and you get a vehicle that was engineered as a gas cart from the factory. The engine, transmission, cooling system, and suspension are all matched to each other and to the frame.

A used gas cart also has a known history. You can inspect it, test-drive it, and ask the seller about maintenance records. A converted cart is a one-off project with unknown reliability. If something fails—the engine, the custom mounts, the fuel system—you may struggle to find parts or a mechanic willing to work on it.

Resale value is another consideration. A converted electric cart is harder to sell because buyers are uncertain about its reliability and safety. A used gas cart, even an older one, has a clear market value and is easier to move if you decide to sell.

Insurance, registration, and local regulations

Golf carts are not street-legal in most places, but regulations vary by state and county. Some areas allow golf carts on public roads under certain conditions (low speed, safety equipment, registration). Others restrict them to private property only. A converted cart may be treated differently than a factory gas cart under local law, and your insurance company may not cover it if they consider it a modified vehicle.

Before starting a conversion, contact your local motor vehicle department and your insurance agent. Ask whether a converted cart can be registered, what safety equipment it must have (lights, mirrors, seat belts), and whether your policy covers it. Some insurers will not insure converted carts at all, or will charge a higher premium. This can add hundreds of dollars to the total cost of ownership.

If you plan to use the cart only on private property (your own land or a private golf course), regulations are less strict, but you should still verify with the property owner and your insurance company.

Frequently Asked Questions

Can I convert a golf cart myself if I have basic mechanical skills?

Basic mechanical skills are not enough. You need welding ability to mount the engine securely, plumbing knowledge to run fuel and coolant lines, and electrical knowledge to wire the ignition and fuel pump. If any of these are new to you, mistakes can create safety hazards—a loose engine mount, a fuel leak, or a wiring fire. Consider hiring a professional for the critical work even if you handle simpler tasks.

What size engine should I use for a golf cart conversion?

Most conversions use 5 to 13 horsepower engines. A 5-horsepower engine is adequate for flat terrain and light loads but feels sluggish on hills. A 13-horsepower engine provides better acceleration and hill-climbing but uses more fuel and creates more vibration. Choose based on how you plan to use the cart and the terrain where you will drive it.

Will a converted gas cart be faster than the original electric cart?

Not necessarily. Electric carts have when ready torque and can accelerate quickly from a stop. A small gas engine has a narrower power band and must rev up to reach peak power. A converted cart may feel faster in a straight line but slower off the line. Top speed depends on the engine size and the cart's gearing, not the fuel type.

How long does a gas engine conversion take?

If you do the work yourself and have experience, plan on 40 to 80 hours spread over several weeks. If you hire a shop, turnaround time depends on their workload and how much custom fabrication is needed. Most shops estimate 2 to 4 weeks from start to finish, though some may take longer if unexpected problems arise during the build.

Can I convert the cart back to electric later?

Technically yes, but it is expensive and impractical. You would need to source a new battery pack, motor, and controller, and remove all the gas engine components. Most people who convert to gas do not convert back. If you think you might want to reverse the decision, a conversion is probably not the right choice for you.