You cannot convert a fifth wheel hitch to a gooseneck hitch on the same truck bed

A fifth wheel and a gooseneck are two different coupling systems that attach to your truck in different ways and locations. A fifth wheel hitch clamps onto a kingpin mounted in the truck bed near the rear axle. A gooseneck hitch is a ball hitch that bolts through the truck bed floor, usually near the center or slightly forward of center. The two systems use incompatible mounting points and cannot be swapped by converting one to the other.

What you can do is remove your fifth wheel hitch and install a gooseneck hitch instead — but this is a replacement, not a conversion. The process involves unbolting the fifth wheel, patching the holes it left, and drilling new holes for the gooseneck ball. Whether this makes sense depends on what trailers you actually need to tow and whether your truck frame can handle the weight distribution change.

Key Takeaways

  • Fifth wheel and gooseneck hitches use different mounting locations and cannot be converted; you must remove one and install the other.
  • Gooseneck hitches place more weight on the rear axle than fifth wheels do, so you need to verify your truck's payload capacity before switching.
  • Removing a fifth wheel leaves holes in your truck bed that must be sealed to prevent rust and water damage.
  • The installation cost and complexity depend on whether your truck bed already has reinforcement and whether you need professional help.
  • Gooseneck trailers and fifth wheel trailers are not interchangeable, so switching hitches means committing to one trailer type.

Why the two hitch types cannot be converted

The fundamental difference is where each hitch connects to the truck. A fifth wheel hitch bolts to a kingpin bracket that sits in the truck bed, usually 3 to 4 feet forward of the rear bumper. The trailer's kingpin (a large pin on the underside of the trailer) locks into the fifth wheel's jaws. This design lets the trailer pivot at a point high in the truck bed, which is why fifth wheels can make tighter turns than gooseneck trailers.

A gooseneck hitch is a ball hitch — similar to a bumper hitch but much heavier — that bolts through the truck bed floor itself. The trailer's coupler (a socket) slides over the ball. Because the ball sits lower and further back in the bed, gooseneck trailers have a different turning radius and weight distribution than fifth wheels.

You cannot adapt one system to work as the other because the coupling mechanism, the pivot point, and the load path are all different. Attempting to do so would create an unsafe hitch that could fail under load.

Weight distribution and payload capacity changes

Before you remove a fifth wheel and install a gooseneck, check your truck's payload capacity in the owner's manual. A fifth wheel distributes weight more evenly because the kingpin connection is higher and more forward in the bed. A gooseneck concentrates more weight directly over the rear axle because the ball sits lower and further back.

If your truck is currently at or near its payload limit with a fifth wheel, switching to a gooseneck may overload the rear axle. You may need to upgrade your suspension, add airbags, or accept that you can tow a lighter trailer. Some trucks are not suitable for gooseneck towing at all, even if they can handle a fifth wheel of the same weight.

Overloading the rear axle causes premature wear on shocks, springs, and bearings, and it can affect braking and handling. Have a truck scales facility weigh your loaded truck if you are unsure whether the switch is safe.

Removing the fifth wheel and sealing the bed

Removing a fifth wheel hitch involves unbolting the kingpin bracket from the truck bed. The bracket is usually held down with four to six bolts that go through the bed floor. Once you remove the bolts, you will have holes in your truck bed that must be sealed.

Do not leave the holes open. Water and rust will enter through them, and they will eventually compromise the bed structure. You have two options: fill the holes with stainless steel plugs and sealant, or patch the bed with a steel plate and sealant. A steel plate is more durable if you think you might reinstall a fifth wheel later. Plugs are simpler if you are committed to the gooseneck long-term.

If the fifth wheel bracket has damaged the bed coating or left rust stains, sand and repaint those areas after sealing the holes. This prevents rust from spreading under the paint.

Installing a gooseneck hitch in the truck bed

A gooseneck hitch requires drilling holes through the truck bed floor and bolting the hitch base to the frame underneath. Most gooseneck hitches come with a template that shows exactly where to drill. The installation typically involves four to six bolts that go through the bed and into the frame.

If your truck bed has a spray-in liner, you will need to remove it from the installation area or work around it. Some people remove the liner entirely; others cut a hole in it and seal the edges. Spray-in liners can trap moisture if not sealed properly around the hitch bolts, so this step matters.

The hitch ball itself bolts onto the hitch base and can be removed or swapped for a different size if needed. Most gooseneck balls are 2 5/8 inches in diameter, but some trailers use 2-inch balls. Check your trailer coupler before buying the hitch.

Professional installation versus doing it yourself

Removing a fifth wheel and installing a gooseneck is a job you can do yourself if you have basic tools, a drill, and a truck lift or jack stands. The work is not complicated, but it is time-consuming and requires care to avoid damaging the truck bed or frame.

Many people have this work done at a hitch shop or truck service center. The cost varies widely depending on your location and whether the shop needs to repair the bed after removing the fifth wheel. Expect to pay anywhere from a few hundred dollars to over a thousand, depending on the complexity and whether additional frame reinforcement is needed.

If you are not comfortable working under a truck or drilling through the bed, professional installation is worth the cost. A shop can also inspect your frame and suspension to confirm that your truck is suitable for gooseneck towing before you commit to the switch.

Trailer compatibility and what you are giving up

Fifth wheel trailers and gooseneck trailers are not interchangeable. If you own a fifth wheel trailer, switching to a gooseneck hitch means you cannot tow it anymore. You would need to sell the fifth wheel and buy a gooseneck trailer instead.

Gooseneck trailers tend to be less expensive than fifth wheels of the same size, and they are easier to maneuver in tight spaces because the hitch is lower. However, fifth wheels offer a smoother ride and better weight distribution for very heavy loads. Think carefully about which trailer type you actually need before you remove the fifth wheel hitch.

If you tow multiple trailers or are not sure which type you will need long-term, consider keeping the fifth wheel and adding a gooseneck hitch to a different truck instead. This avoids the cost and hassle of removing and sealing the fifth wheel.

Frequently Asked Questions

Can I have both a fifth wheel and a gooseneck hitch on the same truck?

Not safely. Both require bolts through the truck bed floor, and their mounting points overlap or conflict. You would have too many holes in the bed, and the hitches would interfere with each other. You must choose one or the other.

Will removing the fifth wheel damage my truck bed permanently?

The holes left behind will cause rust if not sealed, but the damage is not permanent if you patch them promptly. Stainless steel plugs and sealant will stop rust for years. If rust has already started, sand it out and repaint after sealing the holes.

What size gooseneck ball do I need?

Check your trailer's coupler socket. Most gooseneck trailers use a 2 5/8-inch ball, but some older or smaller trailers use 2-inch balls. The ball must match the coupler exactly, or the trailer will not couple safely.

Can my truck handle a gooseneck if it handled a fifth wheel?

Not necessarily. Gooseneck hitches put more weight on the rear axle, so your truck's payload capacity may be lower for gooseneck towing. Check your owner's manual and weigh your truck loaded to confirm it is safe before you tow.

How long does it take to remove a fifth wheel and install a gooseneck?

If you do it yourself, plan on four to eight hours depending on the condition of the bolts and whether you need to repair the truck bed. A professional shop can usually finish in one day, though they may need longer if frame reinforcement is required.