Connect the red cable to the dead battery's positive terminal first, then to the good battery's positive terminal. Then connect the black cable to the good battery's negative terminal, and finally to an unpainted metal surface on the dead car's engine — never directly to the negative terminal. This order matters because it prevents sparks near the battery, where hydrogen gas can collect.
Key Takeaways
- Always connect red to positive (+) on the dead battery first, then red to positive on the good battery — this prevents accidental grounding before both batteries are linked.
- Connect black to negative (−) on the good battery, then to bare metal on the dead car's engine block or frame, away from the battery itself.
- Start the car with the good battery first, wait a few minutes, then start the dead car — do not crank both at once.
- Remove cables in reverse order: black from dead car, black from good car, red from good car, red from dead car.
- If you see corrosion (white, blue, or green crusty buildup) on the terminals, clean it with baking soda and water before connecting.
Why the order of connection prevents electrical damage
The sequence protects both cars from voltage spikes that can fry computers, alternators, and other electronics. When you connect the positive terminals first, you create a direct path between the two batteries before any ground connection exists. This means current flows only between the batteries, not through your car's electrical system.
If you connected the black cable to the dead battery's negative terminal instead of the engine, you would complete a ground circuit through the battery itself. Any spark near a battery can ignite hydrogen gas that collects inside, causing an explosion. By grounding to the engine block or frame instead, you move the spark risk away from the battery compartment entirely.
Step-by-step connection process
Step 1: Position both cars. Park the working car close enough that the cables reach both batteries comfortably — usually 18 inches apart. Turn off both engines. Remove any plastic covers on the battery terminals if your car has them.
Step 2: Attach the red cable. Clamp the red cable's positive clamp firmly onto the dead battery's positive terminal (marked + or red). You should hear a click and feel resistance. Wipe away any corrosion first if the terminal is crusty or discolored.
Step 3: Attach the other red clamp. Connect the red cable's other end to the good battery's positive terminal the same way. Now both positive terminals are linked.
Step 4: Attach the black cable to the good battery. Clamp the black cable to the good battery's negative terminal (marked − or black). This grounds the good car.
Step 5: Ground the dead car. Instead of clamping to the dead battery's negative terminal, clamp the black cable's other end to an unpainted metal surface on the dead car's engine — the engine block, a bolt on the alternator bracket, or the frame. Look for a spot where bare metal shows through any paint. This keeps the spark away from the battery.
Starting the engines in the correct order
Wait 2 to 3 minutes after connecting the cables before starting either car. This allows the batteries to equalize voltage and reduces the strain on both alternators when you crank the engine.
Start the car with the good battery first. Let it run for 2 to 3 minutes. Then start the dead car. If it does not turn over after 30 seconds of cranking, stop and wait another minute before trying again. Continuous cranking can overheat the starter motor.
Once the dead car starts, let both run for another 2 to 3 minutes. This gives the alternator on the good car time to begin recharging the dead battery.
Removing the cables safely
Disconnect in reverse order — this is just as important as connecting correctly. Remove the black cable from the dead car's engine first, then the black cable from the good car's negative terminal. Then remove the red cable from the good car's positive terminal, and finally the red cable from the dead car's positive terminal.
This sequence ensures that the last connection you break is between the two positive terminals. If you removed the positive connections first, you could accidentally ground the cable to the engine while it is still connected to a battery, creating a spark.
Cleaning corroded battery terminals before you start
Corrosion — the white, blue, or green crusty buildup on terminals — creates a poor electrical connection and can prevent current from flowing. If you see corrosion, clean it before connecting the cables.
Mix baking soda with water to make a paste, and scrub the terminal and the inside of the cable clamp with an old toothbrush. Rinse with clean water and dry completely with a rag. If the corrosion is heavy, you may need to use a wire brush or terminal cleaner from an auto parts store. Do not use vinegar or other acids — they can damage the battery case.
What to do if the car still will not start
If the dead car cranks but does not catch after 3 or 4 attempts, stop and let both cars rest for 5 minutes. Continuous cranking drains both batteries and can damage the starter. Try again after the rest period.
If the car still will not start after two full attempts, the battery may be too dead to jump, or the problem may not be the battery at all — it could be a bad alternator, a fuel pump failure, or an ignition switch issue. Disconnect the cables in reverse order and contact a mechanic or towing service.
Frequently Asked Questions
Can I connect the black cable directly to the dead battery's negative terminal?
You can, and many people do without incident, but it is riskier. Grounding to the engine block instead moves any spark away from the battery, where hydrogen gas can collect and explode. The engine block works just as well electrically and is safer.
How long should I let the good car run before starting the dead one?
Two to three minutes is standard. This gives the alternator time to begin recharging the dead battery and lets the voltage equalize between the two. If you start when ready, you put extra strain on both alternators.
What if the cables spark when I connect them?
A small spark when you clamp the final connection is normal. A large spark or sparks that continue means you may have connected something in the wrong order. Disconnect when ready and start over, checking each clamp position against the steps above.
Do I need to drive the car after jumping it?
Yes. Drive for at least 20 minutes to give the alternator time to recharge the battery. A short drive around the block may not be enough, especially if the battery was very dead. If the car dies again within a few hours, the battery may need replacement or the alternator may not be charging properly.
Can I jump a car with a battery that has visible cracks or leaks?
No. A damaged battery can leak acid or explode when charged. If the battery case is cracked or leaking, do not attempt to jump it. Call a towing service instead.