A draft top lift is a hydraulic or mechanical device that holds your convertible's soft top in the raised position when it's up, and helps lower it smoothly when you want it down.
If you drive a convertible, the draft top lift does invisible work every time you raise the roof. It's a strut or hydraulic cylinder mounted between the frame and the soft top structure—usually one on each side. When you raise the top, these lifts support its weight so the motor doesn't have to work against gravity alone. When you lower it, they control the descent so the fabric doesn't drop too fast or unevenly, which would damage the frame and seals.
Without a working draft top lift, your soft top will sag when it's up, won't seal properly against the windshield frame, and can strain or burn out the motor trying to raise a top that's fighting against its own weight. The lifts also keep the top aligned as it moves, so the weatherstripping stays in contact with the frame and water doesn't leak into the cabin.
Key Takeaways
- Draft top lifts are hydraulic or mechanical struts that support the soft top's weight and control how fast it raises and lowers.
- A failing lift causes the top to sag, leak, or refuse to close all the way, and puts extra strain on the convertible motor.
- Most convertibles have two lifts, one on each side, and they usually fail together or within a short time of each other.
- Replacing draft top lifts costs between $300 and $800 per side depending on the make and model, and is not a DIY job for most owners.
How draft top lifts support the soft top structure
The soft top on a convertible is heavier than it looks—typically 80 to 120 pounds depending on the model. That weight sits on a frame made of metal bows and a header rail that connects to the windshield. Without support, gravity pulls the top down and forward, which stresses the motor, the linkage, and the weatherstripping seal.
Each draft top lift is anchored at one end to the car's frame (usually near the rear quarter panel) and at the other end to the top's frame structure. As the top rises, the lift extends and pushes upward, sharing the load with the motor. As the top lowers, the lift contracts slowly, acting as a brake so the top descends at a controlled speed instead of dropping under its own weight.
This controlled descent is critical. If a lift fails and goes completely soft, one side of the top will lower faster than the other, twisting the frame and tearing the fabric. The top can also jam partway down, leaving you stuck with a half-open roof.
Signs that your draft top lifts are wearing out
The most obvious sign is a sagging top when it's fully raised. You'll notice the fabric hangs lower on one or both sides, or the top doesn't sit flush against the windshield frame. You might see a gap between the top and the glass, or water leaking into the cabin along the sides during rain.
Another warning sign is slow or uneven raising and lowering. If the motor runs but the top moves sluggishly, or if one side goes up faster than the other, a lift is likely losing pressure or starting to leak internally. Some owners also report a hissing or popping sound when the top moves, which indicates a hydraulic lift is losing fluid.
If the top won't close all the way or gets stuck partway, don't force it. Stop when ready and have the lifts inspected. Forcing a stuck top can bend the frame and cause much more expensive damage.
Hydraulic versus mechanical draft top lifts
Most modern convertibles use hydraulic lifts, which contain pressurized fluid inside a sealed cylinder. A piston rod moves through the fluid, and the resistance of the fluid controls the speed of movement. Hydraulic lifts are smooth and quiet, but they can leak internally or externally, and once they start to fail, they usually can't be repaired—they must be replaced.
Some older convertibles and a few current models use mechanical lifts, which are spring-loaded struts similar to hood props. They rely on spring tension to hold the top up and resist gravity on the way down. Mechanical lifts are simpler and don't leak, but they can lose spring tension over time, and they're noisier when the top moves.
Regardless of type, both fail eventually from repeated compression cycles, exposure to heat and cold, and the constant load of the top's weight. There's no way to extend their life significantly—maintenance is mainly about catching failure early so you don't damage the top frame or motor.
What happens when a draft top lift fails completely
A failed lift doesn't always stop working overnight. Usually it starts to leak or lose pressure gradually, so the top sags a little more each time you raise it. If you ignore this, the top frame can twist, the weatherstripping can tear, and water will leak into the cabin.
If both lifts fail at the same time (which is common because they wear at similar rates), the top may not raise at all, or it will raise partway and get stuck. The motor will keep running but won't be able to move the top, which can burn out the motor or break the linkage.
A completely failed lift also means the top won't lower smoothly. It can drop suddenly on one side, pinching the fabric or jamming the frame. This is a safety hazard—a falling top can injure someone standing nearby, and a jammed top can trap fingers or hands.
Replacement cost and what to expect at the shop
Replacing draft top lifts is a labor-intensive job because the technician has to remove the soft top or at least lower it partially, disconnect the old lifts, install new ones, and then test the top's alignment and sealing. Most shops charge between $300 and $800 per lift, depending on the make and model. Some convertibles have lifts that are easier to access, while others require more disassembly.
Most shops recommend replacing both lifts at the same time, even if only one is obviously failing. Since they wear together and the second one usually fails within months of the first, replacing both saves you a second trip and a second labor charge. The total bill for both lifts typically ranges from $600 to $1,600.
OEM (original equipment manufacturer) lifts are more expensive than aftermarket replacements, but they're usually more reliable and last longer. Ask your technician whether they're using OEM or aftermarket parts, and what warranty comes with the replacement.
Preventive care for draft top lifts
You can't prevent draft top lifts from wearing out, but you can slow the process and catch problems early. Raise and lower your top regularly—even in winter or when you're not driving the car much. Lifts that sit unused for months can develop internal corrosion or lose pressure. Running the top through its full cycle once a week keeps the fluid circulating and the seals flexible.
Keep the top clean and dry. Dirt and moisture can work into the seals and accelerate wear. After washing the car, dry the top thoroughly, especially around the header rail and the lift attachment points.
Listen and watch for the early signs of failure: sagging, slow movement, uneven raising, or hissing sounds. The sooner you catch a failing lift, the less damage it will do to the top frame and motor. A lift that's starting to fail can usually be replaced before it causes secondary damage.
If you park the convertible for an extended period, raise the top all the way and leave it up. This keeps the lifts under tension and prevents them from settling or losing pressure while the car sits idle.
Frequently Asked Questions
Can I drive with a failing draft top lift?
Yes, but only if the top is fully raised and sealed. A sagging or leaking top will let water into the cabin, and you risk the top jamming or dropping if the lift fails completely while you're driving. Have it replaced as soon as you notice the problem.
What's the difference between a draft top lift and a convertible top motor?
The motor is the engine that powers the top up and down. The draft top lifts are the support struts that hold the top's weight and control its speed. Both work together—the motor provides the force, and the lifts provide the support and braking.
Do all convertibles have draft top lifts?
Most modern convertibles do, but some older models or specialty cars use different support systems. Check your owner's manual or ask your dealer if you're not sure whether your car has them.
Can draft top lifts be repaired instead of replaced?
Hydraulic lifts cannot be repaired—they must be replaced. Mechanical lifts sometimes can be re-tensioned or adjusted, but replacement is usually the only reliable fix. Ask your technician whether your lifts can be serviced or must be replaced.
How long do draft top lifts usually last?
Most hydraulic lifts last between 80,000 and 150,000 miles, or 8 to 12 years, depending on how often you use the top and how well you maintain it. Mechanical lifts may last longer, but they also depend on use and climate.