What an electric hook-up does and why you need one
An electric hook-up is a cable and connector system that lets your motorhome draw power from a campground pedestal or shore power source instead of running your onboard generator or battery. When you plug in, you can run your air conditioning, heating, refrigerator, water heater, and other appliances without draining your battery bank or burning fuel. Most modern campgrounds have pedestals with 30-amp or 50-amp outlets, and your motorhome needs the right cable and adapter to connect safely.
The difference between running on hook-up power and running on battery or generator is when ready: your generator stays quiet, your fuel tank lasts longer, and you can run multiple high-draw appliances at once without overloading your system. For anyone spending more than a night or two at a campground, hook-up power is standard.
Key Takeaways
- Most motorhomes come with a 30-amp shore power inlet, but 50-amp systems are common in larger RVs and provide more simultaneous power draw.
- You need a shore power cable rated for your motorhome's amperage (30-amp or 50-amp), a weatherproof connector that matches your inlet, and sometimes an adapter if the campground pedestal uses a different outlet type.
- The cable runs from the campground pedestal to your motorhome's inlet, and a built-in breaker and surge protector inside your RV protect your electrical system from overload and voltage spikes.
- Before plugging in, check that the pedestal outlet matches your cable connector, inspect the cable for damage, and may support your motorhome's breaker is in the correct position.
- A portable surge protector is a low-cost addition that can prevent expensive damage to your RV's appliances and wiring if the campground's power is unstable.
30-amp versus 50-amp systems: which one you have
Your motorhome's shore power inlet is either 30-amp or 50-amp, and you cannot change it without rewiring your entire electrical system. A 30-amp system uses a three-prong twist-lock connector and can deliver about 3,600 watts of continuous power. A 50-amp system uses a four-prong connector and can deliver about 12,500 watts. Most Class B and Class C motorhomes come with 30-amp inlets; larger Class A motorhomes often have 50-amp.
To find out which one you have, look at your motorhome's exterior near the driver's side or passenger side. You will see a recessed inlet with either three or four prongs. The owner's manual will also list it. If you are buying a cable or adapter, matching your inlet type is non-negotiable — a 50-amp cable will not fit a 30-amp inlet, and forcing it can damage both.
Shore power cables and adapters you actually need
A shore power cable is a heavy-gauge extension cord with a connector on one end (plugs into the campground pedestal) and an inlet connector on the other (plugs into your motorhome). Cables come in 25-foot, 30-foot, and 50-foot lengths. Most people buy a 30-foot cable because it gives you flexibility in where you park relative to the pedestal without being so long that voltage drop becomes a problem.
The cable itself must be rated for outdoor use and the correct amperage. A 30-amp cable is clearly labeled "30-amp" and has a three-prong connector. A 50-amp cable is labeled "50-amp" and has a four-prong connector. Do not buy a generic extension cord — it will not handle the current safely.
You may also need an adapter if the campground pedestal outlet does not match your cable connector. For example, some older campgrounds have NEMA 3R outlets instead of standard RV pedestals. Adapters are inexpensive (usually $15 to $40) and let you connect a 30-amp cable to a 50-amp pedestal or vice versa, though you will be limited to the lower amperage. Always buy the adapter that matches both your cable and the pedestal outlet type.
How to connect your motorhome to shore power safely
Before you plug in, walk around the pedestal and your motorhome's inlet. Check that the outlet is not cracked, corroded, or wet. If water is pooled around the pedestal, do not use it — report it to the campground office. Inspect your cable for cuts, exposed wires, or damaged connectors. If you see damage, do not use the cable.
Next, turn off your motorhome's main breaker (usually labeled "Main" or "Shore Power" on your electrical panel inside). This prevents a power surge from damaging your appliances when you plug in. Plug the cable into the campground pedestal first, then walk to your motorhome and plug the other end into your inlet. Once both ends are connected, turn your main breaker back on. Your motorhome's electrical system will now draw power from the pedestal instead of your battery or generator.
When you are ready to leave, reverse the order: turn off your main breaker, unplug the cable from your motorhome inlet, then unplug it from the pedestal. Coil the cable loosely and store it in a dry location. Never leave a cable plugged in while your motorhome is unattended for extended periods, as weather or ground movement can damage the connection.
What happens inside your motorhome when you plug in
Your motorhome has a shore power inlet (the connector on the outside), a breaker box (inside, usually near the entrance), and wiring that distributes power to your outlets, appliances, and battery charger. When you plug in and turn on the main breaker, shore power flows through the breaker box, which has a built-in breaker that cuts power if the current exceeds your system's rating (usually 30 or 50 amps).
At the same time, your motorhome's battery charger (a converter) begins charging your house battery from shore power. This means your battery stays topped up while you are plugged in, and you can run your lights, water pump, and other 12-volt systems without drawing down the battery. Your 120-volt appliances (air conditioning, microwave, refrigerator on electric mode) run directly from shore power.
If you plug into a pedestal with unstable voltage or a weak connection, your appliances can be damaged. This is why many RV owners add a portable surge protector — a device that sits between the pedestal and your cable and monitors the incoming power. If voltage spikes or drops too far, it cuts the connection automatically. A good surge protector costs $100 to $300 and can prevent thousands of dollars in damage to your refrigerator, water heater, and other electronics.
Common problems and how to avoid them
The most common issue is plugging into a pedestal outlet that does not match your cable connector. This happens when you arrive at a campground and the pedestal has a different outlet type than you expected. The solution is to carry an adapter for your cable type before you need it. Buy adapters for both 30-amp-to-50-amp and 50-amp-to-30-amp scenarios if you travel to different campgrounds.
Another frequent problem is voltage drop over a long cable run. If your cable is 50 feet long and the campground's electrical system is weak, the voltage at your motorhome inlet may be lower than it should be. This can cause your air conditioner to run poorly or your water heater to heat slowly. The fix is to use the shortest cable that works for your parking spot, or to ask the campground office if a closer pedestal is available.
Wet connections are a safety hazard. If it rains while you are plugged in, water can pool around the pedestal outlet or your motorhome's inlet. Do not touch the connection if it is wet. If water gets inside the inlet, turn off your main breaker when ready and do not plug in again until the inlet is completely dry. Some RV owners use a weatherproof cover over their inlet when plugged in to keep rain out.
When to use your generator instead of shore power
Shore power is not always available. Boondocking (camping on public land without facilities) means no pedestal and no hook-up. Some campgrounds have limited pedestals and may not have one available for your site. In those cases, you run your onboard generator to power your appliances and charge your battery.
Even when shore power is available, you might choose to run your generator for short periods — for example, if you are only staying a few hours and do not want to set up cables. Generators are also useful if the campground's power is unreliable and you do not have a surge protector. Running your generator gives you full control over your power and protects your appliances from voltage problems at the pedestal.
Frequently Asked Questions
Can I use a regular extension cord instead of a shore power cable?
No. A regular extension cord is not rated for the continuous high current that shore power draws, and it will overheat and potentially catch fire. Shore power cables are specifically designed and tested for RV use. Always buy a cable labeled for your amperage (30-amp or 50-amp).
What if the campground pedestal is damaged or corroded?
Do not use it. Report the damage to the campground office and ask for a different pedestal or site. A corroded outlet can cause arcing, which damages your cable connector and creates a fire risk. The campground is responsible for maintaining safe pedestals.
Do I need a surge protector if I am only staying one night?
A surge protector is most important if you are staying longer or if the campground's electrical system is old or unreliable. For a single night, inspect the pedestal and cable carefully, and turn off your main breaker before plugging in. If you travel frequently, a portable surge protector is worth the investment.
Can I run my air conditioner and water heater at the same time on 30-amp power?
Yes, but not at full power. A 30-amp system delivers about 3,600 watts total. A typical air conditioner draws 1,500 watts and an electric water heater draws 4,000 watts, so running both at full power would exceed your limit and trip the breaker. You can run them together if you use the water heater on a lower setting or run the air conditioner in a lower mode.
What should I do if my motorhome's breaker keeps tripping when I plug in?
A tripping breaker usually means you are drawing more power than your system can handle. Turn off high-draw appliances (air conditioner, water heater, microwave) and try again. If the breaker still trips when ready after plugging in, the pedestal may have a problem or your motorhome's electrical system may need inspection by a technician.