What a feeler gauge does and why valve clearance matters
A feeler gauge is a set of thin metal blades, each stamped with a precise thickness, that you slide between your engine's valve stem and rocker arm to measure the gap. That gap is called valve clearance or valve lash. If the clearance is too tight, the valve won't fully close and you lose compression and power. If it's too loose, the valve opens and closes with a clatter and wears out faster. Most engines need clearance between 0.004 and 0.010 inches, but your specific engine has its own number — you'll find it in your owner's manual or service manual, not guessed.
Checking valve clearance is one of the few adjustments you can make yourself without special tools beyond the feeler gauge itself. It takes an hour or two and costs almost nothing. Many modern engines with hydraulic valve lifters don't need this adjustment — they self-adjust — but older cars, motorcycles, and some small engines require it regularly. If you've got an engine that's been running rough, ticking loudly from the top, or losing power, a valve clearance check is worth doing before you pay a shop.
Key Takeaways
- Valve clearance is the gap between the valve stem and rocker arm, measured with a feeler gauge blade that matches your engine's specification.
- You must find the correct clearance measurement for your specific engine in the owner's manual or service manual — it varies by engine type and year.
- The engine must be cold and at top dead center on the compression stroke for the cylinder you're checking, or your measurement will be wrong.
- If clearance is out of spec, you loosen the rocker arm locknut, turn the adjustment screw until the feeler gauge blade slides through with light resistance, then retighten the locknut.
- Feeler gauges are inexpensive and come in sets; a basic set costs $10 to $25 and lasts for years.
Finding your engine's valve clearance specification
Before you touch anything, you need the correct number. Open your owner's manual and search the index for "valve clearance," "valve lash," "valve adjustment," or "maintenance schedule." If you have the original manual, it will list the clearance in thousandths of an inch — for example, 0.006 inch intake, 0.010 inch exhaust. Write this down.
If you don't have the manual, search online for "[your year, make, model] valve clearance" or "[engine size] valve clearance." Repair manuals like Haynes or Chilton cover this, and many are available free through library databases or cheap used. Do not guess or use another engine's spec — a 0.002-inch difference changes how the engine runs. If you cannot find the spec, stop and either get the manual or take the car to a shop.
Getting the engine to the right position
The engine must be cold — let it sit overnight or at least three hours after running. A warm engine expands and gives you a false reading. You also need the piston at top dead center (TDC) on the compression stroke for the cylinder you're checking. This means the piston is at the top of its travel and both valves for that cylinder are closed.
To find TDC, remove the spark plug for the cylinder you're working on. Turn the engine by hand using a wrench on the crankshaft bolt (usually at the front of the engine) or by putting the car in gear and rolling it forward slowly. Watch the piston rise through the spark plug hole. When it reaches the top and starts to fall, you're past TDC. Back up slightly so the piston is at the very top. Some engines have a timing mark on the crankshaft pulley that aligns with a pointer on the block — if yours does, use that instead. Once you're at TDC, the rocker arms for that cylinder should have some play in them, meaning they're not being pushed down by the valve springs.
Measuring clearance with the feeler gauge
Slide the feeler gauge blade that matches your spec between the valve stem and the rocker arm. The blade should slide through with light resistance — not so tight that you have to force it, and not so loose that it falls through. If the blade is too thick to fit, the clearance is too tight. If it slides through easily with no resistance, the clearance is too loose.
Start with the blade size your manual specifies. If it doesn't fit, try the next size down. If that one slides through easily, try the next size up. The correct blade is the thickest one that slides through with a slight drag. Write down which blade fit for each valve you check. Do this for all valves on the compression stroke — your manual will tell you which ones those are, or you can check them all if you're not sure.
Adjusting clearance if it's out of spec
If the clearance is wrong, you'll need to adjust it. Locate the adjustment screw and locknut on the rocker arm. The locknut is usually a hex nut that holds the adjustment screw in place. Loosen the locknut with a wrench — turn it counterclockwise — but do not remove it completely. Hold the adjustment screw steady with a screwdriver so it doesn't turn while you loosen the nut.
Once the locknut is loose, turn the adjustment screw. Turning it clockwise (in) decreases clearance; turning it counterclockwise (out) increases clearance. Make small turns — a quarter turn at a time — and check the clearance with the feeler gauge after each adjustment. When the correct blade slides through with light drag, hold the adjustment screw steady and tighten the locknut. Check the clearance one more time after tightening, because the locknut can shift the screw slightly.
Choosing and using a feeler gauge set
A basic feeler gauge set includes blades from 0.002 to 0.025 inches and costs $10 to $25. Buy a set with a handle that holds all the blades together — loose blades get lost. The blades are hardened steel and won't wear out if you treat them gently. Keep them clean and dry. If a blade gets bent or damaged, you can buy a replacement blade for a few dollars, or replace the whole set.
When you slide the blade in, use a light touch. The valve stem and rocker arm are made of steel and won't be damaged by the gauge, but you can bend the blade if you force it. If a blade doesn't fit, don't hammer it — try the next size. After you're done, wipe the blades clean and store the set in a dry place. A feeler gauge set will last for years and is useful for other small engine work, so it's a good tool to own.
When to check valve clearance and what goes wrong
Check valve clearance every 12,000 to 24,000 miles on older engines, or follow the interval in your manual. If you hear a ticking or tapping noise from the top of the engine, especially when it's cold, that's often a sign that clearance has drifted out of spec. If the engine is hard to start, runs rough, or loses power, valve clearance can be part of the problem — though not the only cause.
The most common mistake is checking the engine when it's warm or at the wrong piston position, which gives you a false reading and leads to wrong adjustments. The second mistake is forcing a feeler gauge blade that doesn't fit — you'll bend it and waste time. The third is tightening the locknut too hard, which can strip the threads or bend the rocker arm. Use a normal wrench grip, not a breaker bar. If you're unsure at any step, stop and consult the manual or a shop — a wrong adjustment is worse than no adjustment.
Frequently Asked Questions
Do I need a feeler gauge if my car has hydraulic valve lifters?
No. Hydraulic lifters self-adjust automatically as the engine warms up. Most cars built after the 1980s have them. Check your manual to be sure, but if it doesn't mention valve adjustment in the maintenance schedule, you don't need to do it.
What if I can't find the exact clearance spec for my engine?
Search the service manual for your specific year and engine size — not just the make and model. If you still can't find it, contact a shop that specializes in your vehicle type or post the engine details on a forum for that car. Do not guess, because the wrong clearance will cause problems.
Can I check valve clearance on a warm engine?
No. A warm engine expands and the clearance will be larger than it actually is when cold. Always let the engine cool for at least three hours, or check it the morning after it's been parked overnight. This is one of the most common sources of error.
What does it mean if the feeler gauge blade won't fit at all?
The clearance is tighter than the blade thickness — the valve is too close to the rocker arm. You need to increase clearance by turning the adjustment screw counterclockwise (out). Start with a quarter turn and recheck.
How tight should the locknut be after adjustment?
Snug enough that the adjustment screw won't move if you tap it lightly, but not so tight that you're straining with the wrench. Use a normal grip, not maximum force. If you over-tighten, you risk stripping threads or bending the rocker arm.