What valve clearance is and why it matters

Valve clearance is the small gap between the tip of a valve stem and the rocker arm or cam follower that pushes it open. On engines that don't have hydraulic valve adjusters, this gap has to be set by hand—and a feeler gauge is the tool that measures it. If the gap is too tight, the valve won't close fully and you'll lose compression and burn fuel poorly. If it's too loose, the valve opens late and closes early, which hurts engine performance and can cause a rough idle or misfiring.

Most older engines and many modern trucks and motorcycles still use mechanical valve clearance. Newer cars often have hydraulic adjusters that maintain the gap automatically, so you won't need to touch them. But if your owner's manual lists a valve clearance specification—usually given in thousandths of an inch, like 0.010"—your engine needs periodic checking.

Valve clearance drifts over time as the valve seat wears and the rocker arm or cam follower wears down. Checking it every 30,000 to 60,000 miles, or on the schedule your manual gives, keeps the engine running smoothly and prevents the kind of damage that happens when a valve stays open too long.

Key Takeaways

  • Valve clearance is the gap between the valve stem and the part that pushes it, and it must be measured when the engine is cold and the piston is at the top of its stroke.
  • A feeler gauge is a set of thin metal blades of known thickness that you slide between the valve stem and rocker arm to find the gap.
  • Your engine's manual lists the exact clearance needed for each valve, and the clearance is different for intake and exhaust valves on most engines.
  • Adjustment usually means loosening a locknut and turning an adjuster screw until the feeler gauge slides through with light resistance, then retightening the locknut.
  • If you cannot get the clearance within spec even after adjustment, the valve seat or rocker arm may be worn and the engine needs professional inspection.

How a feeler gauge works and what you're measuring

A feeler gauge is a set of thin, flat metal blades, each stamped with its thickness. They're usually sold in a fan-shaped holder or a small case, and thicknesses range from 0.002 inches to 0.035 inches or more. You select the blade that matches your engine's valve clearance specification, slide it between the valve stem and the rocker arm, and feel whether it fits snugly or loosely.

The goal is a light drag—the blade should slide through with gentle resistance, not fall through freely and not jam tight. If it falls through, the gap is too wide. If it won't fit, the gap is too tight. Once you find the right blade, you know the clearance is correct. If no single blade fits right, you may need to adjust the valve.

Feeler gauges are inexpensive—usually $5 to $15 for a basic set—and they last for years if you keep them clean and dry. Avoid dropping them or bending the blades, and wipe them dry after use to prevent rust.

When and how to position the engine for measurement

Valve clearance must always be checked when the engine is cold—ideally after it has sat for at least an hour. A warm engine expands, and the clearance will read smaller than it actually is. You'll get a false reading and may adjust the valve incorrectly.

The engine must also be positioned so that the piston for the valve you're checking is at the top of its stroke (called top dead center, or TDC). At this point, both the intake and exhaust valves for that cylinder are closed and the rocker arm is at rest. Your manual will show you how to find TDC—usually by aligning a mark on the crankshaft pulley with a mark on the timing cover, or by turning the engine until you feel both valves close as you rock the rocker arm by hand.

Some engines are easier to work on if you remove the valve cover first. Others let you measure through the cover. Check your manual for the layout. You'll need a socket wrench to turn the crankshaft, and you may need a screwdriver or wrench to remove the valve cover.

The step-by-step process for checking clearance

Start by locating the first valve you want to check. Your manual will number the cylinders and list which valves are intake and which are exhaust. Position the engine at TDC for that cylinder by turning the crankshaft with a socket on the crankshaft bolt. You can rock the rocker arm gently with your finger—when both valves for that cylinder feel loose and move freely, you're at TDC.

Select the feeler gauge blade that matches your engine's specification. Slide it gently between the valve stem tip and the rocker arm or cam follower. The blade should fit snugly with light resistance—you should feel a slight drag as you pull it out, but it should not jam or fall through. If it falls through, the gap is too wide. If it won't fit, the gap is too tight.

Write down what you find for each valve. Many engines have 8, 12, or 16 valves, so checking them all takes time. Work through the cylinders in order, repositioning the engine at TDC for each one. Once you've checked all the valves, compare your readings to the specification in your manual. If all clearances are within spec, you're done.

How to adjust a valve that's out of spec

If a valve clearance is too tight or too loose, you'll need to adjust it. Most engines use an adjuster screw and a locknut. The adjuster screw is a bolt that sits on top of the rocker arm or under it, depending on the design. The locknut holds it in place.

Loosen the locknut with a wrench—usually a 10mm or 12mm—while holding the adjuster screw steady with another wrench so it doesn't turn. Once the locknut is loose, turn the adjuster screw slowly. Turning it one way opens the gap (makes it larger), and turning it the other way closes the gap (makes it smaller). Turn it a quarter-turn at a time and check with the feeler gauge after each adjustment.

When the clearance feels right, hold the adjuster screw steady and tighten the locknut firmly. Recheck the clearance one more time—tightening the locknut sometimes shifts the adjuster slightly. If it's still correct, move on to the next valve. If it shifted, loosen the locknut again and fine-tune.

Some engines use a different design: a shim (a thin metal disc) under the rocker arm or cam follower instead of an adjuster screw. Shim adjustment is more involved and usually requires removing the rocker arm or cam shaft. If your engine uses shims, your manual will walk you through the process, or this is a good time to take the engine to a shop.

What to do if you can't get the clearance in spec

If you've adjusted the screw all the way in one direction and still can't get the clearance within spec, something is worn. The valve seat may be recessed (sunk into the cylinder head), the valve stem may be shortened from wear, or the rocker arm contact surface may be pitted. Any of these means the valve needs professional attention—either the valve needs to be replaced, the seat needs to be recut, or the rocker arm needs resurfacing.

Don't force the adjuster screw. If you reach the limit of adjustment and the clearance is still wrong, stop and have the engine inspected by a mechanic. Continuing to drive with incorrect valve clearance will wear the parts faster and can eventually damage the valve or rocker arm.

If you find that one valve is way out of spec but others are normal, that single valve is likely the problem. If all valves are drifting in the same direction—all too tight or all too loose—the issue may be in how you're positioning the engine at TDC. Double-check your TDC procedure against the manual.

Tools and supplies you'll need

A basic feeler gauge set costs $5 to $15 and covers most engines. You'll also need a socket wrench to turn the crankshaft (usually 17mm or 19mm for the crankshaft bolt), a wrench set to loosen and tighten the locknut (typically 10mm, 12mm, or 14mm), and a screwdriver to remove the valve cover if needed. A clean rag and some degreaser help you see the valves clearly.

If your engine has a timing mark on the crankshaft pulley, you may need a timing light or a marker to align it with the timing cover mark. Your manual will tell you if this is necessary. Some engines are easier to work on if you remove spark plugs first—this lets you turn the engine by hand more easily.

Keep the valve cover gasket clean when you remove it. If it's cracked or compressed, replace it before you reinstall the cover. A leaking valve cover gasket will drip oil onto the spark plugs and cause misfires.

Frequently Asked Questions

Do I need to check valve clearance on my newer car?

Most cars built after the 1990s have hydraulic valve adjusters that maintain clearance automatically, so no. Check your owner's manual for the maintenance schedule. If it doesn't list valve clearance, your car doesn't need it. Trucks and motorcycles are more likely to have mechanical valves that need checking.

What happens if I drive with valve clearance that's too tight?

The valve won't close fully, so you'll lose compression in that cylinder. The engine will misfire, run rough, and lose power. Over time, the valve will overheat and burn, and the seat will wear faster. You may also hear a ticking noise from that cylinder.

Can I check valve clearance without removing the valve cover?

Some engines have the rocker arms visible without removing the cover, but most require you to take the cover off to see the valve stems clearly and fit the feeler gauge. Your manual will show the layout. If you can't see the valve stem, you'll need to remove the cover.

How often should I check valve clearance?

Check your owner's manual for the recommended interval—it's usually every 30,000 to 60,000 miles for engines with mechanical valves. If you hear a ticking noise from the engine or notice rough idle, check the clearance sooner. Some engines need checking more often if they're driven hard or in dusty conditions.

What's the difference between intake and exhaust valve clearance?

Exhaust valves run hotter and need a slightly larger clearance than intake valves to account for expansion. Your manual lists both specifications separately. Intake clearance is usually smaller—for example, 0.010 inches—while exhaust might be 0.012 inches. Use the correct spec for each valve type.