A Harley oil change kit contains the oil, filter, and gaskets you need to service your motorcycle in one package

Harley-Davidson sells factory oil change kits that bundle together the specific oil grade your model requires, a replacement oil filter, and crush washers or gaskets for the drain plug and filter cover. Buying a kit saves you from hunting down compatible parts separately and ensures you're using fluids matched to your engine's design. The kit typically costs between $40 and $80 depending on your model year and engine size.

You can buy Harley kits directly from a Harley dealer, through online retailers like Amazon or RevZilla, or from general motorcycle parts suppliers. Dealer kits come with the assurance that every component is factory-approved for your specific model, which matters because Harley engines have different oil capacities and filter types depending on whether you own a Sportster, Softail, Touring, or Street model.

Key Takeaways

  • Harley oil change kits include the correct oil viscosity, a filter, and gaskets sized for your specific model, eliminating guesswork about compatibility.
  • Kit prices range from $40 to $80 and are cheaper than buying each component separately, especially when you factor in crush washers that must be replaced every service.
  • You'll need basic tools — a wrench, socket set, oil drain pan, and filter wrench — but the kit itself contains all the consumables required for the job.
  • Harley recommends oil changes every 1,000 miles for new bikes and every 5,000 miles for established engines, so knowing what goes into your kit helps you plan maintenance costs.

What's actually inside a Harley oil change kit

The oil is the largest component by volume. Harley specifies different weights for different models — Sportsters typically use 20W-50, while some Touring models call for 15W-50. The kit includes enough oil to bring your engine from empty to full, which ranges from about 2.5 quarts on a Sportster to 4 quarts on a Touring bike. Using the wrong viscosity can affect how your engine cools and lubricates, so the kit removes that decision.

The oil filter is a spin-on cartridge specific to your model. Harley filters are not interchangeable across all their bikes — a Sportster filter won't fit a Street 750, for example. The kit includes the correct filter for your engine, along with a new rubber gasket that seals the filter to the engine. This gasket must be replaced at every oil change; reusing an old one risks leaks.

Crush washers (also called crush gaskets) seal the drain plug where oil exits the engine. These are small copper or aluminum rings that compress when you tighten the plug, creating a watertight seal. Harley kits include new washers because they deform during removal and cannot be reused safely. If you reuse an old washer, you risk slow leaks that can empty your oil over time.

How to know which kit fits your Harley

Harley organizes kits by model family and year. You'll see kits labeled for Sportster, Street, Softail, Dyna, Touring, or Trike — and within each family, year ranges matter. A 2020 Street 750 kit is different from a 2023 Street 750 kit because Harley changed the filter design. The easiest way to find the right kit is to enter your VIN or model year on the Harley-Davidson website or a dealer's parts lookup tool.

If you're buying from a non-Harley retailer, cross-reference the kit's part number with your owner's manual or the Harley parts diagram for your model. The manual lists the exact oil capacity, filter part number, and drain plug washer size. Buying the wrong kit means wasting money and potentially damaging your engine if you use incompatible oil or install a filter that doesn't seal properly.

Tools you'll need beyond what's in the kit

The kit gives you the consumables, but you'll need tools to install them. A socket wrench or open-end wrench fits the drain plug — size varies by model but is typically 17mm or 20mm. An oil filter wrench grips the spin-on filter so you can remove it without stripping the housing. A drain pan catches old oil so it doesn't spill on your garage floor or driveway.

You'll also want rags or paper towels, a funnel to pour new oil into the filler cap without spilling, and a torque wrench to tighten the drain plug to Harley's specification (usually 20 to 25 foot-pounds). Over-tightening the drain plug can crack the engine case; under-tightening can cause leaks. A torque wrench takes the guesswork out and costs $20 to $40 if you don't already own one.

Step-by-step process for using your kit

Start by warming the engine for a few minutes so the old oil flows more easily. Turn it off and let it cool for five minutes — hot oil burns, but you want it warm enough to drain quickly. Locate the drain plug on the bottom of the engine (consult your manual for the exact location on your model), place the drain pan underneath, and unscrew the plug by hand or with a wrench. The old oil will flow out; let it drain completely, which usually takes five to ten minutes.

While the oil drains, remove the old filter using the filter wrench. Turn it counterclockwise until it comes free, then unscrew it by hand. Wipe the filter mounting surface on the engine with a clean rag to remove any old gasket material or debris. Take the new filter from your kit, explore a thin layer of new oil from the kit to the rubber gasket on the filter's top, and screw it on by hand until the gasket contacts the engine, then turn it an additional three-quarter turn. Do not use the wrench to tighten it — hand-tight is correct.

Install a new crush washer on the drain plug (the kit includes these), then screw the plug back in by hand first. Use the wrench to tighten it to the torque specification in your manual — typically 20 to 25 foot-pounds. Reinstall the oil filler cap, then pour the new oil from the kit into the engine using a funnel. Check your manual for the exact capacity; you'll pour in most of the oil, then start the engine and let it run for 30 seconds to circulate the new oil through the filter. Turn it off, wait a minute, then check the oil level on the sight glass or dipstick and top off if needed.

Comparing Harley kits to buying parts separately

A factory Harley kit costs $40 to $80 and includes everything matched to your model. Buying components separately — oil ($15 to $25), filter ($12 to $20), and crush washers ($3 to $5) — adds up to roughly the same price, but you risk buying the wrong filter or oil viscosity. Non-OEM kits from aftermarket suppliers like Mobil 1 or Amsoil are sometimes cheaper ($35 to $60), but they require you to verify that the filter fits your specific model and that the oil meets Harley's specifications.

The real savings come from buying kits rather than individual items over time. If you service your Harley every 5,000 miles, you'll buy four kits per year. Buying in bulk from a dealer or online supplier can lower the per-kit cost by $5 to $10. Some riders also choose synthetic oil kits (which cost $10 to $20 more) because synthetic oil lasts longer — some Harley models allow 10,000-mile intervals with synthetic instead of 5,000 miles with conventional, which can offset the higher upfront cost.

Where to buy and what to watch for

Harley dealers stock kits for current and recent model years. Buying from a dealer guarantees authenticity and gives you access to the parts department staff if you have questions about your specific bike. Online retailers like Amazon, RevZilla, and J&P Cycles usually have lower prices and faster shipping, but you need to verify the kit matches your model year before ordering.

Watch for kits labeled "universal" or "fits most Harleys" — these are not reliable. A universal kit might include the wrong filter or oil viscosity, which can cause problems. Always match the kit to your specific model year and engine size. Check the return policy before buying from a new retailer; if the kit arrives and doesn't fit, you want to be able to send it back without losing money.

Frequently Asked Questions

Can I use a non-Harley oil change kit on my motorcycle?

Yes, as long as the oil viscosity matches your manual's specification and the filter is confirmed to fit your model. Many riders use Mobil 1 or Amsoil kits because they're cheaper and widely available. The key is verifying the filter part number against your owner's manual before you buy, because a wrong filter can leak or not seal properly.

How often should I change my Harley's oil?

Harley recommends every 1,000 miles for new bikes in their first 1,000 miles, then every 5,000 miles for conventional oil. Some newer models and synthetic oil kits allow 10,000-mile intervals. Check your owner's manual for your specific model, because recommendations vary by year and engine type.

What do I do with the old oil after I drain it?

Take it to a recycling center, auto parts store, or quick-lube shop — most accept used motor oil for free. Never pour it down a drain or into the ground; it's an environmental hazard and illegal in most places. Many retailers that sell oil change kits also accept used oil for recycling.

Do I really need to replace the crush washers every time?

Yes. Crush washers deform when you tighten the drain plug, and reusing them risks slow leaks that can drain your oil over weeks. The washers in your kit cost a few dollars and take 30 seconds to install, so it's not worth skipping. A leak that empties your oil can seize your engine and cost thousands to repair.

What if my kit arrives and the filter doesn't fit?

Contact the retailer when ready and request a return or exchange. Verify your model year and engine size against the kit's description before you install anything. If you've already opened the kit, most retailers will still accept a return if the filter is unused and the packaging is intact.