What a rear view camera mod involves for your Element
A rear view camera retrofit on a Honda Element means running a camera unit mounted to the back of the vehicle, a power cable through the interior, and a video line to a display screen—usually in the dashboard or headrest. The Element's body design makes this job moderately straightforward compared to some vehicles, since the rear hatch and cargo area give you room to work, but you will still need to remove interior panels and run cables through the cabin.
Most owners choose between two setups: a wireless system that transmits video to an aftermarket head unit or phone, or a hardwired system that connects directly to a new touchscreen or clips into an existing screen location. The hardwired route is more reliable and cleaner-looking, but requires more labor. Wireless systems are faster to install but depend on a stable signal and may have slight video lag.
Key Takeaways
- A rear view camera retrofit requires mounting a camera to the rear bumper or hatch, running power and video cables through the interior, and connecting to a display screen.
- Hardwired systems offer better video quality and no lag, while wireless systems install faster but depend on signal strength and may show slight delay.
- Most Element owners spend between 4 and 8 hours on installation if doing it themselves, or pay a shop $400 to $800 in labor on top of parts cost.
- You will need to remove interior trim panels, run cables along the headliner and behind the cargo area, and may need to drill a hole in the rear hatch or bumper.
- Aftermarket head units with built-in camera inputs are more common and cheaper than OEM-style integrations that match the Element's original dashboard.
Camera placement and mounting options
The most common location is the center of the rear hatch, either mounted to the hatch itself or to the bumper below it. Hatch mounting is cleaner because the cable runs straight down into the cargo area, but it means the camera angle changes slightly when you open the hatch. Bumper mounting keeps the angle fixed and is less noticeable, but the cable has to run under the vehicle or along the exterior to reach the interior.
Some owners use a license plate frame camera, which mounts directly over the plate and is the least invasive option—no drilling required. The trade-off is a narrower field of view and a camera that sits lower than ideal for seeing obstacles directly behind the vehicle. If you choose bumper or hatch mounting, you will need a 1/2-inch or 3/4-inch hole saw to drill through the body panel, and you should seal the hole with weatherproof grommet and silicone to prevent water intrusion.
Running cables through the Element's interior
The power cable typically runs from the rear camera forward along the driver's side, tucked behind the cargo area panels and under the headliner. You will need to remove the rear quarter panels and the headliner trim to access the routing path. The video cable (RCA or HDMI, depending on your system) runs alongside the power line and terminates at your display screen location, usually the dashboard or center console.
The Element's interior layout is relatively forgiving—the cargo area is open and the headliner trim comes off without major difficulty. Use cable clips or adhesive-backed conduit to keep wires organized and away from moving parts. Pay attention to areas near the rear door hinges and the hatch mechanism, where cables can get pinched. If you are running a hardwired system, you will also need to tap into the vehicle's reverse light circuit so the camera activates automatically when you shift into reverse.
Display screen options and integration
An aftermarket touchscreen head unit with built-in camera input is the most straightforward choice. Units from brands like Alpine, Kenwood, and Sony range from $200 to $600 depending on screen size and features. These replace your factory radio and usually fit the Element's dashboard opening with a standard double-DIN bracket. The camera input is already wired in, so you just connect the camera cable and set the display to show the camera feed when reverse is engaged.
If you want to keep your factory radio, you can use a smaller standalone display mounted to the dashboard or a clip-on screen that attaches to an existing vent or mirror. These are cheaper ($80 to $200) but require more manual switching or rely on wireless transmission. Some newer Elements with factory navigation can integrate an aftermarket camera through the OBD-II port, though this is less common and usually requires a professional installer.
Power supply and wiring to the battery
The camera and display screen both need power, which you will draw from the vehicle's battery through a fused line. Run a power cable from the positive terminal through the engine bay and into the cabin, protecting it with a 10 to 15 amp fuse holder positioned within 18 inches of the battery. This is a critical safety step—without the fuse, a short circuit can damage the camera system or create a fire hazard.
Ground the system to a clean, bare metal point on the chassis, not to a painted surface or plastic trim. The rear camera typically draws 0.5 to 1 amp, and a touchscreen head unit draws 2 to 5 amps depending on brightness and features. A single 15 amp fused line is usually sufficient for both, but check your specific equipment's power requirements before you begin. If you are uncomfortable working with the battery and fusing, this is a good step to have a shop handle.
Labor time and cost breakdown
A DIY installation on an Element typically takes 4 to 8 hours, depending on your comfort level with interior trim removal and cable routing. If you are new to this type of work, budget 8 to 12 hours and plan to work in stages—camera mounting and power wiring one day, cable routing and display integration the next. Having a second person to help feed cables through tight spaces and hold panels in place saves time and frustration.
Professional installation at a car audio shop usually costs $400 to $800 in labor, plus the cost of parts. Some shops bundle installation with the purchase of a head unit and offer discounts. If you are buying a complete system (camera, head unit, cables, and installation), expect a total outlay of $600 to $1,500 depending on the quality of components. Budget-friendly wireless systems with a basic camera and phone-based display can be done for $200 to $400 total.
Common pitfalls and how to avoid them
The most frequent mistake is routing cables too close to the rear door hinges or hatch latch mechanism, where they get pinched or cut when the door opens and closes. Trace the path of any moving part before you find a cable. Another common issue is inadequate weatherproofing around the camera hole—water seeps in and corrodes the connector or shorts the camera. Use a rubber grommet and explore silicone sealant generously around the hole.
Reverse light set up is another area where things go wrong. If you tap into the wrong wire or use the wrong gauge wire, the camera may not turn on when you shift into reverse, or it may stay on all the time. Consult a wiring diagram specific to your Element's model year before you cut into any factory wires. If you are unsure, use a relay module designed for camera set up—it is a $20 part that eliminates guesswork and protects the factory wiring.
Frequently Asked Questions
Can I install a rear view camera without removing interior panels?
Not entirely. You need to route the power and video cables from the rear camera to the front display, and the most reliable path runs through the interior along the headliner and behind the cargo panels. A wireless system minimizes this work by eliminating the video cable, but you still need to run power to the camera and the display screen.
Will a rear view camera drain my battery when the engine is off?
A properly installed system with a fused power line will not drain the battery significantly. The camera draws power only when the reverse light is active, and the display screen draws power only when the head unit is on. If you use a wireless system, the camera may draw a small amount of standby power, but modern cameras use less than 0.1 amp at rest.
What if I drill through the hatch and hit something inside?
The Element's rear hatch is mostly hollow, so the risk is low if you drill in the center area away from the edges and hinges. Mark your drilling spot with tape, start with a small pilot hole, and stop if you feel unexpected resistance. If you do puncture a wire or line inside the hatch, you will likely hear a hiss or see fluid, in which case stop when ready and consult a shop.
Can I use a wireless rear view camera instead of running cables?
Yes, wireless systems are available and install faster. The camera transmits video to a receiver connected to your head unit or phone. The trade-off is potential signal interference, slight video lag, and the need to keep the wireless system charged or powered. They work well in open parking lots but can be unreliable in tight garages or areas with heavy radio interference.
Do I need to reprogram my Element after adding a camera?
No. A rear view camera is a standalone accessory that does not integrate with the Element's factory computer or safety systems. It operates independently through the head unit or wireless receiver. If you tap into the reverse light circuit, you are only drawing a signal, not sending data back to the vehicle's systems.