What a Helicoil is and when you need one
A Helicoil is a small coiled wire insert that restores a stripped bolt hole so you can use the original bolt size again. When you overtighten a bolt or remove and reinstall it too many times, the threads in the hole wear smooth and the bolt spins without gripping. Instead of drilling a larger hole and buying a bigger bolt, a Helicoil lets you keep the same bolt size and hole diameter.
You'll recognize a stripped hole by a bolt that turns freely without tightening, or one that tightens partway then spins loose. Helicoils work in metal — aluminum, cast iron, steel — but not in plastic or composite materials. They're common in engine blocks, cylinder heads, and anywhere bolts take repeated stress.
Key Takeaways
- A Helicoil kit includes the insert, a drill bit sized to the stripped hole, and a special tap tool to cut new threads for the insert itself.
- You drill out the stripped hole to a larger diameter, tap new threads into that larger hole, then screw the Helicoil insert into those new threads.
- The Helicoil's inner threads then accept the original bolt size, restoring the hole to working condition.
- The job takes 15 to 45 minutes per hole depending on access and whether you own the tools or are borrowing them.
Gather the right Helicoil kit and tools
Helicoil kits come in standard sizes matched to common bolt diameters. A kit for M6 bolts (metric) or 1/4-inch bolts (SAE) includes the insert, the drill bit, and the tap — the tool that cuts the larger threads. You can buy kits at auto parts stores, hardware stores, or online retailers. The kit should list which bolt size it restores; buy the one that matches your stripped hole.
Beyond the kit, you need a drill with a chuck that holds the bit securely, and a way to turn the tap — either a tap handle (a T-shaped tool) or a power drill on low speed with a tap adapter. A torque wrench is not required for Helicoil installation, but a regular wrench to hold the bolt while you tighten the insert is helpful. If the hole is in an engine or tight space, you may need a socket wrench or box wrench instead.
Drill out the stripped hole to the larger diameter
The drill bit in your Helicoil kit is sized to create a hole that the tap can then thread. This hole is always larger than the original bolt hole. Mark the center of the stripped hole with a marker or center punch so the drill bit doesn't wander. Clamp or hold the part steady — a vise works well for small pieces, or have a helper hold it if it's part of an engine block.
Insert the kit's drill bit into your drill and bore straight through the stripped hole at moderate speed. Let the bit do the work; don't force it. Drill until the bit goes all the way through and breaks through the back side, or until you reach the depth marked on the bit if this is a blind hole (one that doesn't go all the way through). Remove the bit and clear any metal shavings from the hole with a brush or compressed air.
Tap new threads into the enlarged hole
The tap is the tool that cuts threads into the larger hole. It looks like a bolt with flutes (grooves) running down its length. Insert the tap into the tap handle — a T-shaped tool with a square socket that grips the tap's square end. If you're using a power drill instead, attach the tap adapter to the drill chuck and insert the tap into the adapter.
Position the tap at the center of the hole, perpendicular to the surface. If using the tap handle, turn it clockwise slowly and steadily, backing off a quarter turn every half turn forward to break the metal chips. If using a drill, run it on the lowest speed setting and let the tap do the cutting — do not force it. The tap will feel resistance as it cuts; that's normal. Continue until the tap bottoms out or reaches the depth you need. Back the tap out by turning counterclockwise (or reversing the drill) and remove it. Clear the hole of metal shavings again.
Install the Helicoil insert into the new threads
The Helicoil insert comes coiled on a mandrel — a thin rod that holds it in shape. The insert has an outer thread that matches the threads you just cut, and an inner thread that accepts the original bolt size. Screw the insert onto the mandrel's installation tool (a special wrench that comes in the kit) or use the mandrel itself if it has a wrench end.
Turn the insert clockwise into the tapped hole by hand or with the wrench, going slowly and steadily. The insert should sit flush with the surface of the part, or slightly below it — check your kit's instructions for the exact depth. Once the insert is fully seated, the mandrel will break free or unscrew, leaving the insert in place. Some kits require you to break the mandrel by twisting it; others have a breakaway point you snap off by hand. Remove the mandrel completely.
Install the original bolt into the Helicoil
The bolt now screws into the Helicoil's inner threads, just as it would have screwed into the original hole. Insert the bolt and tighten it by hand first to make sure it catches the threads smoothly. If it spins without gripping, the Helicoil may not be seated correctly — back the bolt out and check that the insert is fully in place.
Once the bolt is hand-tight, use a wrench to tighten it to the torque specification for that bolt size and process. If you don't have a torque wrench, tighten it snugly but not with maximum force — the Helicoil is now doing the work that the original threads did. The bolt should hold firm and not spin loose when you try to turn it by hand.
Common mistakes and how to avoid them
The most common error is not clearing metal shavings from the hole after drilling and tapping. Shavings left inside can prevent the Helicoil from seating fully or can jam the tap. Blow out the hole with compressed air or brush it clean after each step.
Another mistake is forcing the tap or drill bit. If you feel strong resistance, stop and back off rather than pushing harder. A tap that breaks inside the hole is very difficult to remove. Let the tool cut at its own pace, and back off every few turns to break the chips.
Finally, check that you bought the correct kit size for your bolt. A kit for M6 bolts will not work in a hole that originally held M8 bolts. The package should clearly state which bolt size it restores.
Frequently Asked Questions
Can I reuse a Helicoil if I remove the bolt later?
Yes. The Helicoil stays in the hole permanently. You can remove and reinstall the bolt many times without damaging the Helicoil, which is the whole point — the Helicoil's threads are harder than the original material and resist wear much better.
What if the tap breaks inside the hole?
A broken tap is difficult to remove and usually requires drilling it out with a smaller bit or using a tap extractor tool. Prevent this by backing off the tap every few turns and never forcing it. If it does break, you may need to take the part to a machine shop.
Do I need a power drill or can I use a hand drill?
A hand drill works for small holes in soft metals like aluminum, but a power drill is much easier and faster for larger holes or harder metals like cast iron. A power drill also gives you better control over speed and pressure.
Can I install a Helicoil in a hole that goes all the way through the part?
Yes, but you need to know the depth you're tapping to. The Helicoil must be fully seated in the tapped threads, so measure or mark the depth before you start. Some kits include a depth stop on the drill bit to help with this.
What size Helicoil do I need if I don't know the original bolt size?
Measure the bolt hole's diameter with calipers or a ruler, or bring the part to an auto parts store and compare it to bolt samples. The staff can tell you the bolt size, and you can then buy the matching Helicoil kit.